Filter Results By:
Products
Applications
Manufacturers
Wafer
thin crystalline material sliced from ingot.
See Also: Wafer Thickness, Wafer Failure Analysis, Wafer Edge, Wafer Resistivity, Wafer Mapping, Wafer Probes, Wafer Probers, Wafer Inspection, Probe Cards
- Scientific Test, Inc.
product
Automated Discrete Semiconductor Tester (ATE)
5000E
Same Proven Technology as all 5000 Series Testers. High Speed Single Test Measure. Capable of Testing Multiple and Mixed Devices. 1KV Standard, 2KV Optional. 1NA to 50A Standard, 100A Optional. 0.1NA Resolution. Complete Self Test. Auto-Calibration. RDSON to 0.1MOHM Resolution. Windows Application Software. Optional Scanner. Optional Wafer Mapping. Optional Curve Trace. MOSFET, IGBT, J-FETTriac, SCR, Sidac, Diac, Quadrac, STS, SBS Transistor, Diode, Opto, Zener Regulator, MOV, Relay. UNDER $23,000.00
-
product
Wafer Level Test
Double sided wafer inspection system is an automatic inspection system for afterdicing wafer chip. It can do double side inspection simultaneously. The appearance defects of wafer chip are clearly conspicuous by using advanced illumination technology. Illumination and camera acquisition mode can be adjusted for various wafer process, like vertical chip or flip chip.
-
product
High Voltage 50 Ω Pulse Generator
TLP-4010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
200mm Wafer Sorter
SortMax200™
Achieve exceptional performance with Genmark's SortMax200™ wafer sorter, designed for handling wafers up to 200mm. The SortMax200™ can be configured to accommodate a maximum number of eight open cassette stations.
-
product
ResMap or DualMap Manual Load
Creative Design Engineering, Inc.
*Type: Table Top*Wafer load: Manual *Wafer size: 2" to 8", 152mm x 152mm*Mini Environment: N/A*Probe Changer: N/A*Aligner: N/A*Size: 12" x 19" x 10"*Range: 1m/ to 10M/*Accuracy: 0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic
-
product
WAFERMAP
WAFERMAP is an award winning software package used to collect, edit, analyze and visualize measured physical parameters on semiconductor wafers. WAFERMAP can import data files from various metrology tools such as ellipsometers, thickness gauges and four point probes. The imported data can then be visualized or printed as line scans, contour plots, 2D or 3D plots or as a histogram.
-
product
Wafer Tester
Tokyo Electronics Trading Co., Ltd.
A vital step in the Semiconductor Value Stream, focusing on electrical screening and consumption of Known Good Die (KGD).
-
product
Defect Inspection Module
EB40
The Class 1 certified E40 and B40 modules (available separately or combined in one module) can automatically detect defects on the entire edge, from zone 1 to 5, and the entire backside. The ability to inspect the entire backside allows for faster root-cause analysis of zone 5 defects since such defects can migrate from the wafer interior.
-
product
Wafer Internal Inspection System
INSPECTRA® IR Series
An infrared internal defect inspection system has been added to the INSPECTRA® series.It is now possible to inspection with both infrared and visual light in one system.
-
product
Wafer Probers
Full Automatic Wafer Prober. Semi Automatic Wafer Prober. High Current Probe Block. 6-inch Manual Prober. 8-inch Manual Prober. 12-inch Manual Prober.
-
product
Quick Silicon Discriminator
HS-QSD
HS-QSD Quick Silicon Discriminator is specially designed for silicon sorting，it can quickly test the silicon type, heavy-dopedt, and can be widely used in all kinds of silicon sorting, like granular polysilicon material, break semiconduct silicon wafer, chunk material, top and tail material and so on. With the three probes, it could show type and heavy type simultaneously, strongly improved the sorting efficiency.
-
product
CMP Tester
CP-6
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
product
Wafer Thickness Measuring System
WT-425
Contact type can measure any materials within 0.2 µm (2 σ at 20℃ ±1℃). The wafer floats positions while measurement points change and it does not damage even thin wafers. Best for the process control of compound wafers and oxide wafers. (SiC, GaN, LT, Sapphire and Bonded Wafers)
-
product
Silicon heavy-doped Tweezer Tester
HS-MRTT
Mini resistivity tweezer tester is used to check heavy-dope silicon. adaptable for little granular material, little broken IC Wafer and other little silicon material. When the resistivity is lower than the set value, it will make alarm.
-
product
Camera Endpoint Monitor based on Real Time Laser Interferometry
LEM Series
Our Real Time Interferometric Process Monitor provides high precision detection of film thickness and trench depth during the etching/deposition process.Depending on applications, LEM camera includes a 670 or 905 or 980 nm laser and when mounted on any dry etch/deposition process chamber with a direct top view of the wafer this generates a small laser spot on the sample surface.Interference occurs when monochromatic light hits the sample surface, resulting in different optical path lengths due to film thickness and height variations in the film.This allows the etch/deposition rate and thus thickness to be monitored in real time, also fringes counting or more complex analysis, providing enhanced process control Endpoint for a wide variety of processes. Additionally interfaces can be detected by their change in reflectivity.
-
product
Probecard testers
MANAGER
Today more complex probe cards are being used. More pins,higher density and larger array requires a new approach inprobe card analysis. With the soaring cost of new generationprobe cards, repair of defective cards becomes an necessity.BE Precision Technology offers all capabilities with the newMANAGER V. Future proof, up to 450 mm full wafer contactprobe cards can be analyzed with up to 88.000 test channels.High-end materials are used to stand extra tough requirements—such as 500 mm diameter diamante viewing window,ultra stiff carbon flip-table, high power Z–stage to generate 600Kg of contact force
-
product
MultiSite Test sockets and Wafer Level
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
product
Non-contact Conductivity Type (P/N) Checker For Quick Check
PN-50α
*Principle: Photovoltaic effect by light pulse irradiation*No damage and no stain by Non-contact method*Possible to check even oxidized film on wafer surface*Instantly discrimination by optical pulse illuminate
-
product
SOI Bonding Systems
An accurate wafer bonding process is the key factor in obtaining high quality single crystalline silicon films on insulating substrates. The EVG850 SOI/Direct Wafer Bonding systems are designed to fulfill a wide range of fusion/molecular wafer bonding applications, with main focus on SOI substrates manufacturing. Ultra clean handling of wafers throughout the bonding process assures high-yield and void-free bonds. All essential steps, from cleaning and alignment to pre-bonding and IR-inspection are combined in one high volume production system. EVG850 is the only production bonding system built to operate in high throughput, high-yield environments and guarantees void-free SOI wafers up to 300 mm.The EVG300 series single wafer cleaning systems are designed for efficient removal of particles. In semiconductor processing, efficient cleaning and particles removal prior to critical process steps enables maximum yield. Wafer Bonding is a process which is strongly affected by particles: each particle on the wafer surface produces a void orders of magnitude larger than its diameter, contributing to a dramatic yield loss.
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
Wafer Defect observing instrument
HS-WDI
Application■Semiconductor wafer■Solar wafer■Solar Cell■Thin-film Cell
-
product
MANIFULATOR
As one of the most important module in Probe_Station, manipulator is an accurate system that probe micro distance() and contact on the electrode of semiconductor wafer, device. ECOPIA's Manipulator is very easy to use and probe arm's elastic plate is good to protect sample's surface, from being damaged by Z direction movement.
-
product
Test Head Manipulators
Cobal 250
The Cobal 250 offers the best-in-class range of motion for universal manipulators with seven degrees of motion. Separate linear movements make it easier for the operator to dock, undock, and redock the test head in seconds. In combination with inTEST EMS docking, the Cobal 250 is compatible with testers for both Wafer Sort and Final Test, minimizing the time and cost when moving a tester between Sort and Final Test.
-
product
WAFER MVM-SEM
E3300 Family
The E3310 is a WAFER MVM-SEM* for next generation wafers, supporting 1Xnm node process development and volume production at the 22nm node and beyond. With its high-speed carrier system employing a dual arm vacuum robot, and low-vibration platform to improve measurement accuracy, the E3310 delivers high throughput and performance for wafer measurements. Its multi detector configuration and unique 3D measurement algorithm also enable stable, high-accuracy measurement of 3D transistor technologies such as FinFET. The E3310 makes a significant contribution to reducing process development turnaround time and improves productivity for next-generation devices.
-
product
Full Wafer Test System
FOX-1P
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
product
Wide Measurement Range Model Of Semi-automatic 4 Point Probe Sheet Resistance/resistivity Measurement
RT-3000/RG-2000 (RG-3000)
*User programable measurement pattern & programmable measuring pattern*Tester self-test function, wide measuring range*Thickness, edge, temperature correction for silicon wafer*Film thickness conversion function from sheet resistance*2 types measuring tester (S version: Standard type, H version: High range resistivity measurement type)
-
product
Flash Memory Test System
T5830
T5830 memory tester, the latest member of its T5800 product family, optimized for testing a wide range of flash memory devices used in mobile electronic devices. The highly flexible T5830 tester has all of the capabilities needed to perform wafer sorting and final testing of price-sensitive flash memories.
-
product
Microwave Plasma Subsystems
AX2600 And AX2700
The AX2600 and AX2700 Microwave Plasma Delivery Subsystems are complete and highly reliable solutions for the cost-effective generation and safe delivery of atomic species to the wafer. Available in 3 kW, these highly reliable, field-proven plasma delivery subsystems deliver highly concentrated atomic species. Suitable for multiple chemistries, the high speed and precision of this plasma system’s automatic tuning guarantees immediate ignition and fast transition from plasma conditions for high productivity. Robust closed-loop control ensures high accuracy, precision, and optimal repeatability of the process from wafer to wafer and system to system.
-
product
IR Inspection System
EVG®20
The EVG 20 offers a fast inspection method, especially for fusion bonded wafers. A live imageof the entire wafer via IR transmission supports void detection down to a radius of 0.5 mm. The infrared inspection system is a perfect match for fusion bonding processes either as the stand-alone EVG 20 tool or as a station in EVG''s integrated bonding systems.
-
product
Wafer Lifetime Measurement with Photoluminescence Detector
WCT-120PL
Measure the calibrated carrier-recombination lifetime of a silicon wafer using both the standard method and the photoluminescence meth
-
product
Low Concentration Type HF/HCl/NH3 Concentration Monitor
HF-960M
The HF-960M uses sensors that offer outstanding corrosion resistance for high-precision, high-speed measurement of low concentrations of hydrofluoric acid, hydrochloric acid and ammonia, and is thus perfect for single-bath and wafer cleaning. The HF-960M is also an environmentally-friendly product that uses lead-free solder for mounting chips on the PCB.
