Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 1-Pole
42-321-101-HI
The 40-321-101-HI (PXI) and 42-321-101-HI (PXIe) are quad 5-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Voltage Sag Generator
SKS-1132GTB
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
product
High Power Programmable AC Source with Transients
61510
Chroma Systems Solutions, Inc.
Power Rating:61511: 12KVA61512: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
product
PFR96
2WE06
The digital controller PFR96 can manage up to 12 independent batteries, a communications port, and two current inputs in size from 96×96 framework. Particularly easy to program thanks to a basic configuration with two parameters and advanced that allows the advanced user the most complete of the power factor correction control.The onboard logic allows corregegre setup via an erroneous wiring of the picture as to or stage of TA.10ms sampling of the voltage allows the calculation of the RMS voltage continuously, identifying network holes and temporary interruptions and detach the active steps immediately to the protection of the contactors and benches.The PFR96 can handle numerous alarms associated to available relays.The means of intervention in the PFR96 adjustment are all customizable for a better quality of the intervention as well as the use of different banks can be equalized for less wear of the contactors.Sampling at variable frequency and RS485 communication for remote control (PFR96 Plus) complete a range of services offering maximum control and quality of the measurement
-
product
Voltage Dips and Interruptions Generator
CSS61000-11
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
product
Transformer Analyzer
505
The UTEC 505 Transformer Analyzer is designed for testing current transformers (CT) and potential transformers (PT) without interruption of the customer’s service. This instrument measures CT admittance, CT ratio, CT primary-to-secondary phase angle and the voltage, current and phase angle of the service. With the ‘Burden CT/PT Option’, it determines the CT secondary burden capability, the regulation of the PT and its secondary burden capability and provides for CT core demagnetization.
-
product
Regenerative Grid Simulator
61800
Chroma Systems Solutions, Inc.
Power rating: Up to 300kVA, single or three phase outputOutput Voltage: 0~330V L-N / 0~570V L-L0~400V L-N / 0~692V L-L opt. without using a transformerOutput Frequency: DC, 30Hz~100HzMaximum power delivered down to 200VAC L-NFull 4 quadrant, fully regenerative up to 100% of output current ratingSpecifically designed for PV inverter, Smart Grid and EV related test applicationsProgrammable slew rate settings for voltage and frequencyProgrammable voltage and current limitsTurn on, turn off phase angle controlLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetParallel output for higher power applications (three phase only)
-
product
Static Inverters
Our static inverters are designed as uninterruptible power supplies (inverter in conjunction with rectifier and battery) to bridge short-term interruptions, power failures, voltage fluctuations, frequency fluctuations or generally to compensate for power disturbances in the data processing sector and in automation and control systems. They are used to supply AC consumers, primarily in the rail and industrial sectors.
-
product
Voltage Dip, Interruption& Variation Simulators
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
product
72.5-Watt DC Power Line Conditioner w/Holdup
44KS3-02
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.
-
product
Power Conditioning
Having a solid power conditioning solution in place before you experience a sag or interruption in power will help you maximize your overall system reliability. Measurlogic provides an array of voltage sag and interruption support solutions for proactive power quality issue prevention. Our DPI and VDC solutions help facilities mitigate future losses due to power quality issues, including lost production time, damaged products, and maintenance after a voltage disruption.
-
product
Switch
TOE 9261
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
product
Voltage Testers
The non-contact voltage tester detects live conductors on cable connections, cable drums, sockets, switches, junction boxes etc. Due to capacitive measurement procedures, no current flow is required and interruptions can be indicated quickly and accurately.
-
product
Cable Locators & Testers
PeakTech Prüf- und Messtechnik GmbH
This new cable detector consisting of a transmitter and a receiver is suitable for the search of voltage-free and voltage - carrying lines, as well as line interruptions and line tracking of surface and flush-mounted lines, pipe systems and even lines in the ground.
-
product
Voltage Sag Generator
SKS-1120GTB
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
product
Power Gail Generators
Voltage dips, short interruptions or voltage fluctuations in the public supply networks can affect electronic and electrical equipment to a large extent. The AC-tests for this are defined in IEC / EN 61000-4-11 and the DC test in the IEC / EN 61000-4-29.
-
product
Voltage Sag Generator
SKS-1120GTA
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
product
IEC61000-4-11 Voltage Dips And Interruptions Simulator Generator
VDS-1120DX
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
product
DC-Powered, AC Voltage Monitor
VAD/VQD
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
product
AC-Powered, AC Voltage Monitor
VAA/VQA
NAI’s VAA and VQA are AC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
product
Voltage Testers
Shenzhen Everbest Machinery Industry Co.,Ltd.
Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g
-
product
Voltage Testers
Non-Contact Voltage (NCV) tester quickly checks for the presence of voltage in AC powered systems. It can be safely used up to 1000 V AC. When AC voltage is detected, the testo 745 gives indication by flashing of its RED LED tip and buzzing of its internal audible buzzer. You can easily determine the hot and neutral legs of an outlet without time consuming and risky removal of the outlet from the outlet box.
-
product
Voltage Meter
MN6I
The mezzanine is designed to measure instantaneous voltage values through six isolated channels with differential inputs.
-
product
Voltage Transformer
PT2
Shanghai Powoo Industry Develop Group Limited
- completely enclosed, good mechanical behavior, suitable for various environments, strong voltage isolation ability, delicate appearance; - the lead wire has a pin format, which makes it easy to be fixed on a PCB; - the mechanical dimensions for this series of PTs are relatively small, hence can be used an electronic component; - good linearity, high precision, wide operating range; - ABS anti-combustion plastic casing; - encapsulated with epoxy resin to ensure strong insulation ability.
-
product
Voltage Probe
Shortsniffer
The ShortSniffer Voltage probe evolved as an effective troubleshooting tool for a small set of problems, but has been quite useful in a variety of non-obvious circuit design, development, troubleshooting, and optimization efforts. Let me tell you about the characteristics of the system and of a few of the successes with the non-traditional uses, and maybe you will find this tool useful in your design or troubleshooting efforts.
-
product
Voltage Indicators
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
-
product
Voltage Detector
KEW 5711
Kyoritsu Electrical Instruments Works, Ltd.
• Senses AC voltage through insulation • Buzzer sounds and tip glows upon ac voltage detection • Powerful flashlight • Dual range (Hi/ Lo) sensitivity • Ready to use without power-on • Designed to meet IEC61010-1.
-
product
Voltage Indicator
Small installation devices for measuring both alternating and direct voltages.
-
product
Voltage Detectors
JSC-88AW
The JSC-88AW is a very reliable way to know for sure whether or not there is voltage downstream from the switches or breakers during power-offs. It dramatically increases the safety of personnel assigned to maintenance work on electrical equipment powered by three-phase voltage. As long as voltage is present downstream of the breakers, one or more (LEDs) of the JSC-88AW will stay lit. A simple visual inspection tells you whether the electrical system is in “Zero Energy” mode. In addition, this new device has been improved to enable resistance to voltage spikes (transients).
