Filter Results By:
Products
Applications
Manufacturers
UHF
Ultra High Frequency operating from 300 MHz to 3.0 GHz.
-
product
Digital Belt-Pack Transmitter
DBu
The DBu transmitter is a 4th generation design with specially developed, high-efficiency digital circuitry for extended operating time on two AA batteries. The transmitter can tune in coarse or fine steps across the UHF television band from 470 to 608 MHz (470-614 MHz for export versions), with a selectable output power of 25 or 50 mW. The pure digital architecture enables AES 256-CTR encryption for high-level security applications.
-
product
Precision Programmable Attenuator
RCDAT-30G-30
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
product
Data Link Transponder
Model 290
Kratos Defense & Security Solutions, Inc.
The Model 290 UHF data link transponder is a command receiver, digital command decoder, digital telemetry encoder, telemetry transmitter, and target interface enclosed in a single lightweight package. The transponder receives commands transmitted by the ground control station and interfaces with the vehicle management computer or autopilot.
-
product
Ruggedized Encryption Device for Voice & Data Communications
MMC3000
The R&S®MMC3000 is a fully ruggedized tactical crypto device for encrypting and decrypting voice and data communications at the highest security levels. It is based on the ELCRODAT 4-2 but has no NATO crypto algorithms. Since it is TEMPEST-proof, it can work with HF/VHF/UHF radio, satellite communications and line transmission equipment. It is ideal for deployment on stationary and mobile platforms in rugged terrain and in naval and airborne environments.
-
product
Amplifiers
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.
-
product
Adapters
These coaxial adapter products provide a convenient solution for most interconnection needs. A specially threaded adapter along with a selection of male and female BNC, TNC, N, SMA, RCA, F, UHF and Mini-UHF coaxial connector ends allows one to construct almost any adapter required, both in-series and between-series.
-
product
UHF- SATCOM Antenna System
AT-6000
This antenna includes UHF-SATCOM and VHF/ GPS/ GSM/ IFF functionality. It is especially designed to increase the communications capability on vessels and submarines which are limited in number of mast or space. The AT-6000 antenna finds its utilization also in re-fit programs.
-
product
Wireless
UHF In Ear Monitoring System -900
The 425-900 UHF In Ear Monitoring System sets new standards in terms of unmatched audio clarity, robust RF performance coupled with advanced configuration features to meet the most demanding professional applications.
-
product
DVB-T Amplifier Module
The COMM-connect DVB-T Amplifier Module is a very versatile module, for use in multiple applications, including driving High Power amplifiers or stand alone Gap-filler. The amplifier covers both VHF & UHF bands, and can be combined with several COMM-connect filter options.
-
product
UHF Multi-Frequency Belt-Pack IFB Receiver
IFBR1B
Wireless IFB (interruptible fold back) systems are used for talent cueing and crew communications in broadcast and motion picture production. In other cases, the IFB system is used by directors and other management to monitor program audio during a production. The IFBR1B receiver provides simplicity and flexibility in a package that is intuitive for untrained users to operate. Despite its tiny size, the new IFBR1B receiver offers excellent performance on par with all of Lectrosonics’ IFB products.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
product
Low Noise Amplifiers
WA Series
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
product
ICE 3000 Series
ICE3006
The ICE3006 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in the cosite environment. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the three-port design (LOS and SATCOM). The ICE3006 incorporates extensive Built-in-Test capability and is qualified for airborne applications. A mounting tray is available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3006. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
GPS Transponder
M7-GX
The Raveon model M7 GX transponder is a rugged high-speed UHF (450-480MHz) GPS transponder with a built-in 12-channel GPS receiver. It has up to 5 watts of RF power output, and operates as both a GPS transponder for tracking, and a radio modem for sending and receiving data.
-
product
Portable PD Monitoring of Medium and High Voltage Power Equipment with UHF, AE, and HFCT
PDiagnosticM
Power Monitoring and Diagnostic Technology Ltd.
The PDiagnosticM is a portable system that utilizes UHF, AE, and HFCT sensor modules to monitor PD signals from Medium and High Voltage power equipment.The system is ideal for monitoring critical power assets to find and monitor intermittent PD signals and to analyze the developing PD trends. The PD type is determined by automatic pattern recognition and internal defects can be found at an early stage.The system provides advanced protection with alarm functions and our Deep Learning data analysis capabilities utilizing our proprietary Intelligent Cloud Diagnostic Technology.
-
product
Frequency-Agile Compact IFB Transmitter
IFBT4
The Lectrosonics IFBT4 UHF transmitter was designed for use in broadcast, motion picture, theater, and stage applications where extended operating range and high-quality audio are essential. The IFBT4 can be used as a stand-alone device or patched directly into popular intercom systems.
-
product
Diversity Receiver
R400a
The R400a is a high performance, triple-conversion, frequency synthesized, UHF receiver fully compatible with all Lectrosonics 400 series transmitters, and a number of analog models. The proprietary audio processing includes a DSP (digital signal processor) for very low distortion and a superior signal to noise ratio. The DSP eliminates a compandor and its artifacts to provide exceptional audio quality when operating in its native hybrid mode. Special DSP algorithms also provide compatibility modes for use with Lectrosonics 100 and 200 Series analog transmitters.
-
product
Wireless
Radio Talkback
The 430-00-XX is a rugged, full duplex UHF base station ideally suited to any application within TV studio, OB/SNG and theatre environments where clear and dependable wireless communication is critical. Both single and dual antenna versions are available covering the 440-470MHz band, each with 32 channels and programmable RF power level from 10 to 50 Watt.
-
product
VHF & UHF Couplers for the PowerMaster and PowerMaster II
VHF-1.5K (2m), VHF-1.5K-2 (1.35m), UHF1.5K (440-450 MHz), UHF-1.5K-2 (420-440 MHz)
-
product
RF Power Monitors
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
product
Mini UHF Connectors
Pasternack Mini UHF connector category has many part numbers, most of which are RoHS and REACH compliant. Mini UHF connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These Mini-UHF connectors are built to precise RF and microwave industry specifications. Mini-UHF connector products are manufactured in male or female gender with 50 Ohm impedance. UHF mini connector products are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These connector series in mini UHF designs include crimp/solder or solder attachment methods. Other mini-UHF connector options include Push-On or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this mini UHF connector series is in-stock. Not only are these in stock, they will ship the same day as well.
-
product
Bluetooth® Testing
Bluetooth® technology is a global wireless standard which allows convenient and secure connectivity over short distances for many devices, such as computers, laptops, cell phones, cameras, networks and medical equipment.The technology uses short-wavelength UHF radio waves to exchange data between two devices and is based on the IEEE 802.15.1 Wireless Networking Standard.In order to ensure reliability, quality and safety, TÜV Rheinland provides high-quality Bluetooth® testing services to qualify and list Bluetooth® hardware and software components and products. Our experts have the knowledge to assist you in all of your Bluetooth® testing and certification requirements, guaranteeing you reliable and secure Bluetooth® devices.
-
-
product
Partial Discharge Monitor
doblePRIME PD-Guard
The doblePRIME PD-Guard continuously monitors partial discharge (PD) in equipment such as transformers, rotating machines, cables and switchgear.The doblePRIME PD-Guard provides local alarms and will communicate data and notifications across standard interface channels and through to networked supervisory systems. It analyzes RF emissions in the HF, VHF and lower UHF ranges.
-
product
Spiral Antenna
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.
-
product
UHF Connectors
Pasternack UHF connector category contains many part numbers, the majority are RoHS and REACH compliant. UHF connector series in this category will terminate to coax or terminal. Pasternack UHF connectors are built to precise microwave and RF industry specifications. Connectors in UHF series are constructed in male, female or sexless gender with 50 Ohm impedance. UHF connector items are available in 4 hole flange, bulkhead, 4 hole panel or mountless options. These connector designs include clamp/solder, crimp/solder, field replaceable or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this UHF connector series is in-stock. But not just in stock, these connector will also ship the same day as they are purchased.
-
product
Advanced Handheld Partial Discharge Detector for Electric Power Equipment with Multi-Sensor and Cloud Diagnostic Technologies, Data Management Software, and Test Management App
PDetector
Power Monitoring and Diagnostic Technology Ltd.
The PDetector is an ideal device for On-Line Partial Discharge (OLPD) testing of MV and HV equipment which employs all 5 types of OLPD sensor technology: Ultra-High Frequency (UHF), Acoustic Emissions (AE), Ultrasonic, High Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV). The information from multiple sensors gives the PDetector the versatility to detect all types of PD in all types of substation apparatus. The exact type of PD activity can be determined effectively using multiple on-screen data spectrum analysis. The PDetector greatly simplifies and standardizes the routine OLPD testing procedure by using the Intelligent Patrol function, the PDetector App, and the PMDTCloud. It is a very powerful and helpful tool for substation operators to conduct routine testing in a substation quickly, to determine what the issue is, and where it is located.
-
product
T/R（Transceiver Module）
Chengdu KeyLink Microwave Technology Co., Ltd.
RF Amplifiers up to 500MHz LDMOS and GaN are applied for this frequency range of Narrow and Broad band including VHF, UHF bands amplifier modules and offers low risk on heat radiation and long term sustainable operation. Also, controlling and protection circuits are designed.
-
product
Ancillary Infrastructure
TideStation – Permanent
All data can be recorded locally and broadcast to a central command and control point as required. Within the TideStation enclosure is all the ancillary infrastructure required to maintain power to the Tide and Met equipment interfaced and the chosen communications systems. There are two standard TideStation variants: Option 1 – Single Port ipBuffer, TideStation Junction Box, optional Satel UHF radio. Configuration Example: TideMaster, VRS-20 and Pressure Sensor. Option 2 – 4 port ipBuffer, TideStation Junction Box, optional Satel UHF radio. Configuration Example: TideMaster, VRS-20, Pressure Sensor, miniCT, METPak II, plus other instruments.
-
product
Plug-On Transmitter
DPR
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. The DPR can tune in 100 kHz or 25 kHz steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 25 or 50 mW. The purely digital architecture utilizes AES 256-CTR encryption for high level security applications.
