Filter Results By:
Products
Applications
Manufacturers
Thermocouples
Thermocouples are junctions of two dissimilar metals that produce a very small voltage proportional to the temperature of the junction.
- Pickering Interfaces Inc.
product
PXI 23 Channel Low Thermal MUX
40-620-022
Pickering 40-620 Multiplexer modules are similar to other Pickering Multiplexer cards except thermal EMF is substantially reduced to <1.5V with 250nV thermal stability. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC microvolt measurements.
-
product
Gauge Type T Thermocouple Wire
W-TW-24
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-KDP
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
product
Smart Analog to Digital
618/619
Supports thermocouples, RTD's, strain gauges, voltage in, 4-20mA, thermistors, and resistorsUp to 16 differential input channels plus sensor excitationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateAuto-calibration eliminates trimpotsLow power consumption
-
product
Thermocouple, Contact, ITA, Chromel, Type K (°C)
610113133
Primary mating contact 610131131.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Thermocouple Thermometers
These industrial instruments’ claim to fame is their accuracy. General offers a wide variety of thermocouple thermometers distinguished by features such as the number of independent channels supported (from one to twelve) –such as the DT4208SD 12 Channel ThermoCouple Thermometer, ruggedness (the ability to survive a fall) – such as the Rugged DT62 Two Channel Thermocouple Thermometer, compatibility with one or more thermocouple types – such as the DT80-2 Two Channel “K” & “J” Thermocouple Thermometer, and data logging capability – such as the DT4947SD 4 Channel Thermocouple Thermometer with Excel Formatted Data Logging SD Card. Our portfolio of thermocouple probes is just as extensive.
-
product
THERMO MODULE OF THE COMPACT DEVICE FAMILY
ES620
This module measures temperatures using 16 electrically insulated measuring channels for temperature sensors. The adjustable acquisition rate per module is 10 samples/s to 0.1 samples/s. Signal smoothing occurs through a parameterized software filter, and high measuring accuracy is possible through 21 Bit resolution. The automotive measuring range is -210 C to 1372 C (-346 F to 2502 F); J, K, and N type thermocouples are used. Data transfer to PC occurs via Ethernet.
-
product
8 Inputs Temperature Data Logger – Thermocouples
HD32.8.8
Rugged data logger with 8 inputs for K, J, T, N, R, S, B and E type thermocouple with miniature connector temperature probes.
-
product
16-Channel VME Analog/Thermocouple Input Module
V450
The V450 is a 16-channel 24-bit VME isolated analog-to-digital converter module which can acquire a wide range of DC voltages, including thermocouple readings with automatic cold junction compensation. Each channel is independently isolated with it's own A/D converter, signal conditioning, input protection circuits, and test relay.
-
product
Signal Calibrators
Nagman Instruments & Electronics Pvt. Ltd
If you are looking for Signal calibrators that are best in industry, head over to Nagman website immediately. We have a range of signal calibrators, loop calibrators, milliamp calibrators, process meter and more. Depending on the requirement at hand, you can find a signal calibrator that is best suited for your industry. Signal calibrators can be used for calibrating thermocouples, RTD, transmitters, etc. while loop calibrators are used for calibrating controllers, indicators, etc. Nagman’s range of signal calibrators are handy, light weight, portable and durable.
-
product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K47
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
Alumel, Type K (°C) Contacts
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
K Thermocouple Surface Probe
TP755
Surface thermocouple Type “K” probe. Tolerance according to IEC 60584-2 standard.
-
product
Suitable for Thermocouple Sensors Approved to ATEX and IECEx standards
TTC200X
Approved to ATEX and IECEx standards allowing for use in hazardous area applications.
-
product
Cable Assembly, Receiver, Thermocouple, 20", TB-4353
540291010162
Cable Assembly, Receiver, Thermocouple, 20", TB-4353
-
product
Thermocouple Power Sensors
N8482A
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
product
Gauge Type T Thermocouple Wire
W-TW-44P2
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T01
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
31-Channel Thermocouple Input Signal Conditioner
U2802A
The Keysight U2802A 31-Channel Thermocouple Input module is a thermocouple input signal conditioner device that functions to convert low input voltage signal from a thermocouple into an output voltage range suitable for the data acquisition device. The U2802A thermocouple signal conditioner is to be used together with the U2355A and U2356A model data acquisition to enable thermocouple inputs.
-
product
FD-11613, 8-Channel Temperature Input Device for FieldDAQ
785640-01
8-Channel Temperature Input Device for FieldDAQ - The FD-11613 measures up to eight thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11613 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11613 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11613 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
product
Complete Systems
Universal Testing Device
The universal testing device is intended for a diverse range of measurement and automation tasks in laboratories and in test engineering. Thermocouples, RTDs and other sensors can be directly connected. Electrical AC/DC values can also be acquired with the universal testing device.
-
product
5 ½ Digits Dual-Display Digital Multimeters
SDM3055
The SIGLENT SDM3055-SC includes a multiplexer that provides multi-point measurement capabilities. The scanner features 12 multi-purpose + 4 current channels and supports the following measurement functions: DCV, ACV, DCI, ACI, 2WR, 4WR, CAP, FREQ, DIODE, CONT and TEMP (RTD and Thermocouple ). It provides a convenient and versatile solution for test applications that require multiple measurement points or signals and is an ideal tool for R&D burn-in and production testing.
-
product
RTD and Thermocouple Calibrator
PTC-8010
This RTD and Thermocouple Calibrator is an ideal device to handle all of your temperature calibration needs in a truly rugged, low-cost package. It combines virtually all widely used thermocouples and RTDs in one device - you'll never have to worry about finding a temperature device you can't calibrate. This is especially true when calibrating "smart" or pulsed RTD transmitters, where many other rtd calibrators fail to work or operate at reduced accuracy specs.
-
product
Calibration Equipment
Tempsens offers a complete range of temperature calibration types of equipment for calibration of Contact Type Sensors (Thermocouple, RTD) and Non-Contact Type Sensors (Pyrometer). Our Calibration range is from -196°C to 3200°C
-
product
NI-9210, 4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module
784788-01
4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module - The NI‑9210 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9210 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
product
Thermocouple, ITA, 36", 24 AWG Thermocouple Wire K Type, Single Ended (3 Amps)
7-409803000-036
Thermocouple, ITA, 24 AWG Thermocouple Wire K Type (3 Amps), Twisted Pair, Single Ended
-
product
Data Acquisition Recorders & Loggers
DAS1800
The DAS1800 can be configured for a wide variety of applications with slots for 10 input modules each supporting 4 or 8 measurement channels. Acquire data from any sensor with a voltage or current output (with shunt), or directly measure voltage, resistance, or temperature using thermocouples or resistance temperature detectors (RTDs).
-
product
Digital Telemetry Solutions
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
product
Smart Probes
A wide selection of rugged smart probes for your sensing needs. From non-contact IR sensors to a full range of sensor types including Temperature, Humidity, Process, RTD, Thermocouple, pulse, and mor...
-
-
product
Copper, Type T (°C) Contact
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
