Filter Results By:
Products
Applications
Manufacturers
Thermal Test
Designed to produce a temperature change in a device. The magnitude and rate of this change should induce a sufficient thermal stress fatigue to identify sources of potential failure without causing catastrophic failure of all components. (sigmasystems.com)
See Also: Thermal, Thermal Shock
- Pickering Interfaces Inc.
product
PXI 32 Channel I/O, High Side Driver
40-413-001
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
product
Aircraft Escape Systems
The Emergency Interseat Sequencing System (EISS) was designed an qualified for the F-15K Fighter and has since been installed in the F-15SG and F-15SA configurations of the F-15. The system consists of Thermal Batteries with Initiators, a Digital Interseat Sequencer, Mode Selector, and customer provided cabling Electro-Explosive Devices (EEDs). The system is operated from either thermal battery and aircraft 28Vdc for redundancy. A separate field Test Set (EESSTS) performs both complete system continuity tests and an operational test of the total system installed in the aircraft. The sequencer is programmable and could be used in any escape system.Based on the initiation point, Forward or Aft Seat Handle, Internal or External Canopy Jettison Handles, and the Mode Selector setting, the Sequencer provides firing pulses to the EEDs to support canopy removal, ejection seat inertial reel activation(s) and ejection seat catapult firing(s). Sensing capabilities are provided to determine system state, canopy gone, seat gone, so as to provide the optimum escape timing.
-
product
Thermal imagers
Thermal imagers sensitive in MWIR and LWIR spectral bands are one of crucial surveillance technologies for defense/security sector. These imagers have also found mass applications outside defense sector. Testing thermal imagers is needed for both manufacturers, maintenance workshops and final users for a set of different and important reasons. Hi-tech test equipment can help significantly in manufacturing, maintenance, training, purchase optimization, and optimal use of these expensive imagers.
-
product
Combined Environmental Reliability Test System
VTC SERIES
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
product
Rubber Testing Equipment
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fatigue resistance, peel strength, vertical & horizontal combustion, smoke density, limiting oxygen index, the flame spread rate, the surface resistance, surface resistivity, volume resistivity, the breakdown voltage, dielectric strength, dielectric loss, antistatic properties, Aging test (UV, Xenon lamp, carbon arc lamp, ozone) etc.
-
product
Explosion Proof UV Inspection Light
he Labino MB Hercules Ex is an extremely durable product specifically developed for use in areas where the risk of an explosion is high. Offshore Oil Rigs, Refineries, Aerospace, and Defense often require explosion proof products to ensure safety for their inspection teams. The Midbeam Hercules Ex has successfully completed extremely tough tests, including tests for thermal conditioning, Impact Tests, Drop Tests and IP tests that led to the ATEX certification (Certificate: ITS17ATEX402144X). This unique product is suitable for use in extreme weather conditions varying from 104° Fahrenheit (+ 40° Celsius) to minus 4° Fahrenheit (- 20° Celsius).
-
product
Liquid Thermal Conductivity Instruments
THW-L1
The Transient Hot Wire (THW-L1) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity, thermal diffusivity, and specific heat instrument for measurement of liquids and pastes in accordance with ASTM D7896-19. The THW-L1 was designed with speed and operational simplicity in mind. With a single measurement of 1 second in duration, small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity, thermal diffusivity, and specific heat. The THW-L1 utilizes a non-stationary measurement approach and rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a thin heating wire 40 mm in length and is completely inserted into the sample to be tested.
-
product
Shoe Cold Insulation Tester
UI-FT09
Shoe Cold Insulation Tester is used to test shoe cold insulation ability / thermal insulation against cold performance..
-
product
Walk-In Climatic Test Chamber
WEIBER climatic test chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. The climatic chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperaThe walk in option provides facility to test large sized, heavy weight specimen as well as the facility to test the specimen in bulk. Capacities ranging from 2000 to 10,000 Lt are available. Standard as well as customizable sizes and facilities are provided.
-
product
Thermal Shock Chamber
ATS Series
Thermotron thermal shock chambers meet a variety of testing needs and come in three configurations: vertical, horizontal, and double duty. A product transfer mechanism automatically transfers products under test from hot to cold zones and back when programmed in the controller.
-
product
Thermal Runaway Test Machine
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Thermal runaway test machine test the whole vehicle or the complete vehicle-borne ion battery system or the subsystem of vehicle-borne lithium-ion battery system, including a lithium ion battery and an electrically connected lithium ion battery. The applicable standard is UL 2580, IEC 62619.
-
product
Reliability Testing Services
Innovative Circuits Engineering, inc
Our Reliability Testing Services make it possible for us to work with many different customers who manufacture devices that need tests such as pressure pot, temp cycle and more.The focus of our reliability testing lab is to provide our customers with an array of services and tests that fulfill all of their reliability testing needs. Whether you need preconditioning, thermal shock, pressure pot, or many other reliability testing needs, we are happy to be of service.
-
product
Environmental Test Chamber
High and Low Temperature Test Chambers, ESS Environment Stress Screening, 2 Zone Thermal Shock Test Chamber, 3 Zone Thermal Shock Chambers, Walk-In Chambers, Burn-in Room and Aging Test Chambers, Altitude Chambers, Industrial Drying Oven, Salt Spray Test Chambers, Temperature Humidity Vibration Comprehensive Test Chamber, Test Machine Series, Custom Made Environmental Test Equipment, Double-Layer High and Low Temperature Chamber, Explosion Proof Temperature Chamber For Power Battery, etc.
-
product
Instruments
Advanced Thermal Solutions, Inc.
ATS designs and fabricates the most extensive line of thermal test instruments specifically designed for the electronics industry. These research-quality, state-of-the-art instruments include Pressure, Temperature and Velocity Measurement Systems, Airflow and Heat Flux Controllers, Micron-level Thermography Systems and Cold-Plate Thermal Characterization Systems.
-
product
Customized Thermal Management Test Bench Solutions
Our IPEtec test bench engineering business unit plans and provides customized test bench solutions for the development and validation of automotive AC components. We offer a full range of test benches and media-supply modules for the automotive developer’s thermal management needs. Moreover, we support the development of new cooling systems for hybrid power trains, for battery and engine cooling. New hybrid power trains are opening up additional fields of heat-pump technology development aimed at optimizing the energy balance of automotive air conditioning.
-
product
In-chip Monitoring Solutions
Range of in-chip monitoring and embedded sensing fabrics allows for meaningful data to be captured at each stage of a chip’s lifecycle. Manufacture | Wafer Sort | Package Test | In-field | End-of-lifeDeep in-chip sensing, telemetry & analytics enablement. Highly distributed, real-time thermal analysis. Supply voltage sensing for power optimisation. Chip assessment for chip to product appropriation.
-
product
Thermal Division Overview
MPI Thermal is a division of MPI Corporation. With over 60 years of combined thermal control system experience with our international engineering teams, this has brought about a comprehensive product portfolio of thermal air stream systems for today's manufacturer's environmental test chamber needs.
-
product
Protective Bonding Testers
RMO-E Series
The RMO-E instruments are designed and ideal for testing protective bonding (grounding) of equipment following the standard IEC 61010-1. Also, they can measure the resistance of high, middle and low voltage circuit breakers, high-current bus bar joints, cable splices, and welding joints. The instruments accurately measure not only in factory environments but also in high-induction fields and substations.Both models generate a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the protective bonding testers automatically generate increasing current before measuring and decreasing current after the measurement. Consequently, this significantly decreases magnetic transients and ensures great accuracy.These instruments can store up to 500 measurements in the internal memory and have a built-in thermal printer available as an option.DV Win software communicates with the RMO-E earth resistance meter via USB or RS232 interface. It allows a user to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.The RMO-E series contains two models, RMO60E and RMO100E. The main difference between these two models is in the maximal test current:60 A DC for RMO60E100 A DC for RMO100E
-
product
Gem Testers
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
A diamond tester is a portable device used to check the authenticity of diamonds and test materials for their thermal and electrical conductivity. It can accurately indicate if the stone is a real diamond based on the gem's physical properties.
-
product
Automatic Dielectric Constant Tan Delta And Resistivity
No Balancing and Calculation required to calculate Volume / Surface Resistivityand Dielectric Constant.Complies IEC 60250, IS 4487, Test jig Conform to ASTMD 257Built in Thermal PrinterSerial port RS232 for data downloading.Can be used to check liquid sample with Three Terminal oil cell.Storage 100 Test reports
-
product
Thermal Shock Test Chamber (Three Zone)
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
product
PXI/PXIe 16-Channel Digital Output Module
40-412A-024
16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
product
TIM Characterization Tools
Thermal Engineering Associates, Inc.
Combining Thermal Test Vehicles (TTVs) with Thermal Test Boards (TTBs) results in a set of tools that perform the basis for TIM thermal characterization under application-oriented measurement conditions. Availability of these tools creates a de facto standard that enable both TIM manufacturers and TIM users to compare measurement results under the same conditions.
-
product
Software
BatteryPro
Chroma Systems Solutions, Inc.
The software is item driven with built-in tests – meaning no programming is required at all. Users are able to read data from the BMS controller and also includes thermal chamber control. Battery Pro Software supports Chroma’s regenerative battery cyclers and provides a safe and stable testing environment.
-
product
Fully Automatic Transformer Oil Test Set
1. Test as per International standards NMC insulating oil testers are fully automatic micro controller based system,completely self-contained,compact and portable giving smooth variable test voltage from 0 to 60, 80, or 100 kV for testing the dielectric strength of insulating oil in accordance with all international standards like IEC156/IS6792/ASTM D 1816/ASTM D877/ UNE 21 specifications.2. Auto mode NMC insulating oil testers are fully automatic type.1) IEC-156, IS6792, ASTM D 877, ASTM D 1816, UNE 21.2) Withstand Test A3) Withstand Test B4) 5 Minute Test5) User defined3. 100 Test results storage capacity NMC insulating oil testers has a storage capacity of 100 test results which can be recalled and printed.4. LCD display NMC insulating oil testers use LCD for easy readability of the BDV test results.5. Built in printer The printer used is a thermal paper print outs.The paper rolls can be easily installed by any person.6. User Friendly RS 232 Interface RS 232 interface is very easy to use to communicate stored data which can be saved in text format.7. Safety protection Safety interlocks are provided on the test chamber.Zero interlock protection to ensure operator safety.8. Accurate Performance The kit not only has all basic functions of an insulating oil tester but also has unique features that are seldom seen in similar products. For e.g. PROOF test A, PROOF test B, 5 Minntes test, LCD to display all test data.It ensures high work efficiency and reliability in any tough environment.
-
product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
product
Thermal Profiler
SPS Smart Profiler
The SPS Smart Profiler stands out as the best and “smartest” temperature profiling data collection system available. The hardware is the best in temperature tolerance design using an LCP (Liquid Crystal Polymer) enclosure for better protection and faster cool down between profiles. The design of the SPS thermal shields allows for easy and secure opening and closing, durability that meets the most stringent of drop tests, and temperature tolerance capabilities that exceed all previous KIC profiler and shield models.
-
product
Automated Thermal Stress System
ATSS Series
Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:
-
product
Automated Test Equipment
Smart, swappable fixtures and flexible test bedsMulti-site setups, including multi-threadingLong-wire, short wire, and wirelessBed-of-nails for in-circuit testing (ICT)RF, high-speed digital, and thermal designsSolidWorks design expertise and global manufacturing (e.g., US, Mexico, China)Multiple options for mass interconnects (VPC, MAC Panel) and harnessesBuilt-in self-test (BIST) fixtures and calibration tools
-
product
Instruments
Organizations working on new thermosets or new thermoset formulations need an intimate understanding of how these materials cure before they can proceed to the next step in the research, quality control, or production process. What happens when the material is heated? When is the best time to apply pressure to squeeze out voids? How fast does the material react at 120C? 150C? 180C? Most organizations today address this need by curing a sample for an arbitrary amount of time before using inexact, error-prone manual methods, or complex thermal analytical instruments to test cure state. Maybe the sample has reached the end of cure, but maybe not. With traditional methods, it’s difficult to tell for sure. How can organizations determine whether they’re processing materials longer than necessary? Dielectric cure monitoring lets them know for sure.
