Filter Results By:
Products
Applications
Manufacturers
Steppers
A device that translates electrical pulses into precise mechanical movement. The output shaft may deliver rotary or linear motion. (www.seanet.com)
- TEAM SOLUTIONS, INC.
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
Hematology Analyzer
ABX Micros 60
Process efficiency in Hematology- Impedance technology, photometry- Microsampling: Only 10 µL- Smart card based memory storage (optional)- No compressor (stepper motor technology)
-
product
Load Pull
All Focus tuners use extremely efficient calibration and tuning algorithms and control electronics based on LAN control (iTuner). This is a merger our proven tuner technology with state of the art control electronics to create the latest tuner generation. The on-board micro-processor and tuning firmware form a self-contained and fully calibrated test instrument. The micro-processor inside the tuner accepts ASCII format communication, via an industry standard TCP/IP interface, controls up to nine stepper motors (tuner axes) and executes interpolation and tuning functions for single probe (CCMT) tuners (one probe per frequency range). For tuners with more than one independent probe (MPT) covering the same frequency range to allow for harmonic tuning, external computing power is required, because of the exponentially growing number of combinations of tuner states (slug positions).
-
product
Stepper Motor Controller for PCI
PCI321
The PCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.
-
product
Stepper Motor,Ultra-Thin Linear Stage
TSAXXX-C
Model:TSAXXX-C Stepper Motor,Ultra-Thin Linear Stage Rotation with super grinding ,slide with v-shapped rail ,elastic couplings have adopted import high-quality products,supply quality assurance .The design of the limited switches and zero switch and standard interface are converient for output of sigal ;Equipped with handwheel in the back of motor ,achieve manual adjustment;Standard hole is convenient for combined-dimensional . The height is 30mm,the largest height is only 44mm.Application for little height of space,little travel,high resolution fields.
-
product
Motors
Pittman and Haydon Kerk motor lines span a wide range of sizes in brushed, brushless and stepper motor technologies. We provide rapid turn-around for prototypes and production orders. Custom designs and special engineering requirements such as special shaft diameters, lengths and mounting flanges are welcome.
-
product
Custom Automation Equipment And Assembly Machinery
Automated test equipment, precision positioning robots, stepper motor, and servo motor mechanisms in support of testing and repetitive manufacturing from TetraTek Products, Inc.
-
product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
product
Stepper Motor ,High-Precision Linear Stages,Application for Labs
KSAXXX-11-X
Model:KSAXXX-11/12-X Stepper Motor ,High-Precision Linear Stages,Application for Labs KSA xxx-11/12 series high-precision motorized translation stages has adopted new structure and crafts ;.Application for motion fields which needs high linearity.For example :femetosecond laser experiment, laser processing,three-dimensional scanning measured system and so on.
-
product
Stepper Motors
We carry a wide variety of stepper motors including washdown stepper motors for use in wet or dusty environments, 2-phase bipolar motors, integrated stepper motors, and more.
-
product
Electronic Controllers
CAES designs and manufactures stepper and brushless DC controllers for aerospace applications. A variety of interfaces (1553, RS422), input voltages, and drive schemes are available. Custom requirements are welcomed.
-
product
Analog Panel Meters
Jewell Instruments offers a wide range of moving iron, moving coil, and stepper motor analog panel meters in A&M, Emico, Jewell, and Modutec Series.
-
product
Electromechanical Testing Machines
Stand model in four-pillar design with electronic force transducer, flanged to the movable testing machine crosshead and electronic position transducer for measuring the crosshead path. The machine is driven by a quartz-precise stepper motor with two ball screws. Complete with integrated displacement measuring device 0.01 mm over the entire travel distance as well as additional displacement transducer with connecting cable and holder
-
product
Ultra-High Precision Motorized Vertical Stages
Model: KSAV Ultra-High Precision Motorized Vertical StagesKSAV1010/2030-ZF is new product, wedge vertical stage with.high-resolution, so many advantages: high-stability, high-load and capacity in vertical position,self-locking.applicatin filed: high postion precision,high load capacity,limited space and so onCharacteristic ◆Cross ball screw rail,precion ground ensure resolution, straightness,high load capacity, limited space◆small travel improve resolution◆stepper motor and DB9 interface, choose controller flexibility◆switches ensure safe when operate◆ planning other specification and size
-
product
Business Machines
Innovation in 3D Printing, Automated Lighting, Mobile Communications, Commercial Printing and other industries is driving demand for linear actuators, lead screws and rails as well as DC motors. Haydon Kerk Pittman’s diverse product range and technology often makes it the preferred single source supplier of components or custom sub-systems. Whether you choose stepper, DC brushed or brushless technology as part of your rotary or linear mechanism, Haydon Kerk Pittman can provide the optimum solution.
-
product
Engine Control
StepGenerator4
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
product
Hybrid Stepper Motors
Hybrid stepper motors from IMS are available in rotary sizes NEMA 11 (28 mm) through 34 (85 mm), and linear actuator sizes NEMA 17 (42 mm) and 23 (57 mm). These extremely robust, long-life motors carry out precise step-by-step movements that are controlled by a stepper motor drive, such as MForce, to comprise a stepper motor drive system.
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
Mezzanine System
5093
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
product
Advanced 4-Axis Servo & Stepper Motion Controller with High-Speed Triggering
PCI-8164
ADLINK PCI-8164/PXI-8164 is an advanced 4-axis motion controller. Compared with the PCI-8132/34 series, PCI-8164/PXI-8164 offers better linear and circular interpolated move and continuous contouring performance-ideal for advanced pulse train motion control solutions and complicated motion and pick-and-place applications.
-
product
Econo Motion Controllers
DMC-41x3
The DMC-41x3 motion controller is one of Galil's latest generation, stand-alone motion controller. Compared with the DMC-21x3 controller, the DMC-41x3 offers the following enhancements: 100BASE-T Ethernet, aux RS232 port, USB port, uncommitted analog inputs, up to 15 MHz encoder frequencies, more program memory, and faster sample frequencies. The DMC-41x3 also accommodates the same stepper and servo motor drives used in the DMC-40x0 series and allows two 4-axis 750 W drives to be installed in the 8-axis controller package. The DMC-41x3 is available as a box-level or card-level motion controller. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100BASE-T, or USB. It includes optically isolated I/O in addition to analog inputs and outputs. The DMC-41x3 controller and drive unit accepts power from a single 20-80 VDC source.
-
product
Advanced 2-Axis Servo & Stepper Motion Controller
PCI-8102
PCI-8102 is an advanced stepper/servo motion controller to meet high performance/cost ratio request. Compared with PCI-8132/PCI-8134, PCI-8102 mainly offers three features: Software security check for users' software, card ID setting and circular interpolation control. Besides, PCI-8102 also provides users many additional features with cost-effective way. For details, please refer to the user manual.
-
product
Stepper Motor Controller for VMEbus
VME321
The VME321 Intelligent Stepper Motor Controller with Amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.This VMEbus board has a 6U form and is also available as 3U VMEbus board.
-
product
Rotary Actuators
A line of of products that combine a high rigidity hollow rotary table with a closed loop stepper motor and driver package. It retains the ease of use of a stepper motor, while also allowing for highly accurate positioning of large inertia loads.
-
product
Entry-Level 4-Axis Servo & Stepper Motion Controller
PCI-8134A
The PCI-8134A is a 4-axis entry-level motion controller. A PCI interface provides plug-and-play capability for easy maintenance, and supports up to 12 cards in one system, to control 48 motors. The PCI-8134A provides pulse train command output up to 2.4MHz and encoder input up to 2.4MHz in 4xAB phase mode. Programmable acceleration and deceleration allows flexible programming of in-house applications, and dedicated motion I/Os shorten system installation. The PCI-8134A also supports 2~4 axis linear interpolation for simplified synchronous motion. The PCI-8134A is a cost-effective motion controller enabling implementation and control of most of point-to-point, conveyer, and load-and-unloader applications.
-
product
Motor Control
A product portfolio that offers motor drivers (brushed, brushless, stepper, load & relay) and integrated motor control systems for all your motor control solutions.
-
product
Drives
Haydon Kerk and Pittman offer a range of advanced Stepper and Brushless motor drivers to complement its linear and rotary motors. Our Haydon Kerk and Pittman drives are available in many configurations from simple analog controlled single quadrant drives to fully programmable servo motion controllers.
-
product
High-Precision XY Stage
V-731
Physik Instrumente GmbH & Co. KG
Reference-class XY stage. Travel range 205 mm × 205 mm (8"). Unidirectional repeatability to 0.1 μm. Velocity to 200 mm/s. Incremental encoder with 10 nm resolution.Optionally with stepper motor.
-
product
Closed-Loop Motorized Linear Actuators with Built-in Encoders
LAR-E Series
Zaber's LAR-E Series products are computer controlled, precision lead screw driven, motorized linear actuators (electric cylinders) with integrated feedback encoders. A built-in encoder allows closed-loop operation and slip/stall recovery features. Each electric cylinder is wired for use with Zaber's A-Series stepper motor controllers, or they can be used with any 2-phase stepper motor controller through the panel mount DB15 connector. When connected to our A-Series controllers, the actuators are designed to be "plug and play" just like all of Zaber's other products.
-
product
4-axis Stepper Motion Controller
PCI-8144
The ADLINK PCI-8144 is a pulse train motion controller ideal for stepper motor control. This controller provides T/S curve control, on-the-fly speed change, non-symmetric acceleration and deceleration profile control, and simultaneous start/stop functions. This controller also offers card index settings for multiple cards in one IPC system and a hardware security function to prevent unauthorized use of in-house developed applications.
-
product
High Precision Motorized Rotation Stages
RAK
Model: RAK High Precision Motorized Rotation Stages New construction ,new technology;the key index has up to the international level of the similar products by strictly inspection .This series products are used to laser precision processing,three dimensional scanning measurment system and so on . ◆Stepper motor drive ,finish angle adjustment automatically; ◆Worm and worm wheel has adopted durable to friction material ,high reliable accuracy of rotation . ◆High precision ,ultra steel axises of importing ,achieve high precision, high load stable motion ◆Outer circle has scale, interface , convenience for signal’s output ◆Circle grating and encoder combine with MC series controller ,achieve closed-loop control Standard stepper motor and DB9 interface, choose to controller flexibility ◆three phase stepper motor and servo-motor is planning
