Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Single 16 to 1 RF MUX SMB 75 Ohm
40-835-001
The 40-835-011 is a single 75 Ohm 16-channel RF MUX in a single PXI slot. The module has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40-835 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
PXIe-4154, 2-Channel, 8 V, 3 A PXI Programmable Power Supply
781155-01
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
product
Power Sensors
RTP5006
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 6 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements.This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Millimeter Wave Amplifiers
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
product
Standard CW Amplifiers
The BT-AlphaA-CW series is a range of classAB RF power amplifiers covering the 10kHz to1MHz frequency range.• Rugged, solid-state design - high reliability• Extremely high phase and amplitude stability• High linearity• In-Built Protection• Very fast blanking• Capable of pulsed operation• Competitively pricedSuitable for CW radar, communications, HF/VHF jamming, particle accelerator applications/plasma systems, plasma, RF heating and otherscientific applications.
-
product
Non-RMS Responding Power Detectors
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
product
PXIe High-Speed Source/Measure Unit, 13 V, ± 1 A or 6 V, ± 3 A, 18 W
M9111A
The M9111A is a 1-slot, 2-quadrant PXIe module that provides stable, glitch-free sourcing and sinking, and high accuracy measurements. It offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. With industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading, the M9111A SMU speeds test time. The high-speed M9111A can change its output voltage, stabilize that voltage, and accurately measure current from Amps down to micro-Amps all in less than 1 ms so that you can move on to the next test as quickly as possible.
-
product
Power Amplifier, RF
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
-
product
GaN Power Amplifiers > 5W
Macom Technology Solutions Holdings Inc.
MACOM GaN RF power amplifier solutions are designed with the latest GaN-on-SiC and GaN-on-Si technologies. Our MACOM PURE CARBIDE series of GaN-on-SiC power amplifiers offers high performance and reliability for the most demanding applications. Our expanding GaN portfolio is designed to address the challenging requirements of Aerospace & Defense, Industrial, Scientific and Medical applications and 5G wireless infrastructure. MACOM GaN products deliver output power levels ranging from 2 W to over 7 kW and exhibit best in class RF performance with respect to gain and efficiency. For sensitive Aerospace & Defense applications MACOM can offer a US only supply chain with AS9100D Certification.
-
product
PXIe Measurement Accelerator
M9451A
The M9451A PXIe Measurement Accelerator combined with Option DPD Digital Pre-Distortion & Envelope Tracking Gateware shows what is possible when you combine state of the art FPGA's with Keysight's trusted measurement expertise and PXIe's high speed data handling. As part of Keysight's RF PA/FEM Characterization & Test, Reference Solution, this combination provides unprecedented performance for demanding envelope tracking and digital pre-distortion measurements required for testing modern power amplifiers (PAs) and front-end modules (FEMs). Hardware acceleration provides better than 20x speed improvement over Keysight's previous host-based Reference Solution, with closed/open loop digital pre-distortion (DPD) and envelope tracking (ET) measurements taking just tens of milliseconds and overall measurement times less than 70 ms.
-
product
Microwave Amplifiers For Immunity and Wireless Testing
AR RF/Microwave Instrumentation
AR’s microwave amplifiers are just as tough and dependable as our RF amplifiers, and they are backed by the same comprehensive warranty. Our microwave amplifiers offer the hard-to-find combinations of power and bandwidth in frequency increments and power output you need for today’s test applications.
-
product
Fiber Transmitter With Fiber Amplifier
FTFA 844
- Auto Switch over from Fiber to RF & Vice versa- Works as Transmitter & Fiber Amplifier- AGC / MGC - Automatic & Manual Gain Control- Very High MER / BER- High Quality DFB Lasers with Isolators- RF Input : 78dB ~ 90dB- Optical Input : -8dBm ~ +2dBm- Optical Wavelength : 1310nm- Power : 110VAC ~ 240VAC, 50HzSpecifications:- Bandwidth: 47 ~ 860 MHz- Input RF Level: 75 ~ 85dBuV- Input Optical Level:- -8dBm ~ +3dBm- SMPS Power Supply:- 110V AC ~ 265V AC- Power Consumption: 50Watt- AGC Range: 0 ~ -8dBm
-
product
Optical Node
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Philips CGD914 amplifier module that employs both GaAs and Si dies.* 4 outputs, output level ≥100dBμV when optical input at -1dBm.* Plug-in fixed attenuator, fixed equalizer.* Optical power indication for -7 ~ 0dBm.* FP laser or DFB laser for return path.* RF test point for forward path and return path.* Optional SNMP responser unit supporting JIUZHOU HFC Net Managing software.* AC 60V or AC 220V power supply.* Aluminum die-casting housing.
-
product
Space-Qualified Products
Teledyne RF & Microwave has a rich history with more than 40 years of space heritage without any in-flight failures. We serve the commercial, scientific, military, and government communities with best-of-breed space solutions. As one of the first companies receiving MIL-PRF-38534 Class K certification, Teledyne earned the space community's trust by commercializing and supporting the industry's most comprehensive line of space-qualified products, from components to solid-state power amplifiers to integrated microwave assemblies.Teledyne's quality certifications include MIL-PRF-38534, Classes H & K (TRB Option). Our space-qualified RF and microwave portfolio covers frequencies from 5 MHz to Ka-band. Explore more below for an overview of our product offerings and capabilities.
-
product
Power Limiter, 0.01 to 50 GHz
N9355F
The N9355F power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
product
Amplifiers
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.
-
product
Low Noise Dual Band VCO
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
product
Radio Frequency (RF) And Microwave Products
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
product
Low Noise Pre-Amplifiers
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
product
RF POWER AMPLIFIERS
BLWA Series
A) RF-Sample Ports I) 3x 208 V AC / 60 HzB) External Dual Directional Coupler L) LAN Remote ControlC) IEEE-488.2 GPIB Remote Control S) Internal RF Switching UnitD) Front Panel RF Connectors R) RS-232C Remote ControlE) RF Power Indication (digital) U) USB Remote ControlF) Gain Adjustment W) Liquid CoolingH) DC Supply X) External Control of other Amplifiers
-
product
RF Milliwatt Meters
Type NDB-2 and NDB-3
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
product
Gain Blocks
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
product
PXI Source/Measure Unit
Keysight PXI source/measure unit (SMU) offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. It delivers industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading for faster test time.
-
product
RMS Responding Power Detectors
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
product
RF Training Kit And Lab Sheets
Y1800A
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
product
Power Sensors
RTP5540
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 40 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Microwave System Amplifier, 0.5 to 26.5 GHz
83017A
The Keysight 83017A microwave system amplifier is a compact, off-the-shelf amplifier designed for systems designers and integrators. This amplifier provides power where you need it to recover system losses and to boost available power in RF and microwave ATE systems. The ultrabroad bandwidth from 500 MHz to 26.5 GHz allows the designer to replace several narrow bandwidth amplifiers with a single Keysight amplifier, eliminating the need for crossover networks or multiple bias supplies.
-
product
RFFE Protocol Analyzer and Exerciser
PGY-RFFE-EX-PD
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
product
MXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5182B
Take your designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading ACPR & output powerTest wideband devices with factory-equalized 160 MHz RF bandwidthReduce the time spent on signal creation with Signal Studio software, including LTE, WLAN & GNSSLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
product
High-performance LPDA
ALP690
The ALP690 is a high-performance LPDA (log periodic dipole array) antenna with a bypassable, built-in RF amplifier for use with wireless microphone receivers in location or studio production. The design delivers +4 dBd of passive gain in a directional pattern to extend operating range, and, when DC power is applied, the amplifier applies gain to overcome loss in long coaxial cable runs. By offering both active and passive operation modes, the ALP690 can be used as a receiver antenna (active or passive) and as a transmitter antenna (passive only).
-
product
Wideband GaN Amplifiers
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
