Filter Results By:
Products
Applications
Manufacturers
Prototyping
Construction of first working designs.
- Pickering Interfaces Inc.
product
PXI Prototyping Module, 2-Slot no Connector
40-225A-002
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785168-01
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
Prototyping
Is an early sample, model, or release of a product built to test a concept or process or to act as a thing to be replicated or learned from.[1] It is a term used in a variety of contexts, including semantics, design, electronics, and software programming. A prototype is generally used to evaluate a new design to enhance precision by system analysts and users.
-
product
PCI-8511, 1‑Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-01
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785163-01
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
Universal 3D Metrology Software Platform
PolyWorks
Defining the cutting edge of 3D metrology, the PolyWorks software suite maximizes productivity, quality, and profitability when integrating 3D measurement technologies into an industrial manufacturing process. From part and tool design and prototyping down to final inspection of assembled products, PolyWorks offers advanced solutions to cover the complete product development cycle. Interfacing directly with major brands and technologies of single-point and point cloud 3D measurement devices through plug-in extension modules, this universal platform also supports a wide array of native point cloud and polygonal model file formats.
-
product
Electrical Development & Redesign
Your product description goes hereARC’s electrical engineering team has the leg up when it comes to developing or redesigning to your specific requirements.All the way from prototyping to cable design to integration, our talented team of clever engineers can deveop a prototype quickly and get your project off on the right foot. Whether it is a new solution or if you are redesigning an obsolescent FPGA system, our team can provide quickly and effectively while still keeping your budget in mind.
-
product
Hybrid Verification Platform
HES-DVM
HES-DVM™ is a fully automated and scalable hybrid verification environment for SoC and ASIC designs. Utilizing the latest co-emulation standards like SCE-MI or TLM and newest FPGA technology, hardware and software design teams obtain early access to the hardware prototype of the design. Working concurrently with one another they develop and verify high-level code with RTL accuracy and speed-effective SoC emulation or prototyping models reducing test time and a risk of silicon re-spins.
-
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-01
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
PXI DeviceNet Interface Module
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
product
uSD Logger Shield
IFB-11001
This micro SD logger shield enables time-stamped logging of any signals measured by your Arduino project! Whether sensor shields, breakout boards or datalink connections, this shield will get your logger project up and running quickly. We've included an MCP79410 Real-Time-Clock module for flexible supply voltage timekeeping, which includes an on-board battery holder for a CR1220 battery (included, and is installed). In addition, the micro SD card is interfaced through a high-speed translator IC and supplied with a high-current LDO to meet the demands of the SD standard. Each pin of the Arduino has an offset pin attached for easy wiring to the massive 13x9 pin prototyping area, including the pins connected to the ICSP header! Whether you're using a Mega, Due or Uno, this board has your interfacing needs covered! Finally, the micro SD holder is a push to lock, push to unlock type, which makes it really easy to both install and uninstall your card.
-
product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
Flying Probe Tester
Pilot 4D V8
The Pilot 4D V8 represents the latest frontier in flying probe test technology; it is the complete solution for those who want maximum performance: the highest test speed, low to medium volume, test coverage and flexibility, for prototyping, manufacturing, or repairing any type of board. Its vertical architecture is the optimum solution for probing both sides of the UUT simultaneously.
-
product
Data And Telecommunication
Imec is an ideal partner to help you remain on top. We are developing solutions taking into account long-term industry roadmaps. You will profit from our collaborations with the largest players in the ecosystem. Moreover, as the emerging technologies involve new materials and components, we also offer capacity for integration, prototyping, small-to-medium volume production and – through our partners – even large volume manufacturing.
-
product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
product
Analog Simulator
MPLAB® Mindi™
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
product
VXI Prototyping Kits For RF Modules, Analog And Logic Circuits
• VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.
-
product
Real-Time Target Machines
Speedgoat offers a range of high performance multi-core, multi CPU target computers (target machines) with i3 and i7 CPUs up to 4.2 GHz, and up to 20 cores. Each is optimized for a different application area, from mobile controller prototyping (RCP) to multi-target rack systems for Hardware-in-the-Loop (HIL).
-
product
SparkFun Sensor Kit
Do you have a good understanding of various sensors or need a variety of them for a project? The SparkFun Sensor Kit includes a sensor for just about every job. With everything included in this kit, you'll be able to sense gesture, humidity, temperature, motion, touch, sound, altitude, acceleration and more! These are some of our favorite sensors from each category. But wait, there's more! The SparkFun Sensor Kit now includes several of our sensor boards that feature the Qwiic Connect System for rapid prototyping!
-
product
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device
783924-01
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2942 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786165-01
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
Software Platforms
Discover complete solutions for Hardware-in-the-Loop (HIL) and Rapid Control Prototyping (RCP) testing. OPAL-RT offers the most advanced real-time simulation software platforms for power systems, power electronics, aerospace and automotive sectors: RT-LAB (Multi-domain, MATLAB/Simulink® based), HYPERSIM (Power Systems), and NI VeriStand (Automotive).
-
product
Optical Engineering Software
FRED
FRED Optical Engineering Software simulates the propagation of light through any optomechanical system by raytracing. Whether your design is imported from CAD, a lens design program, or constructed from within the software, FRED provides engineers with the essential tools for virtual prototyping of optical systems.
-
product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785171-01
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
Silver Button Sockets
For BGA, QFN, or LGA applications, GTP contact technology provides >94 GHz signal speed and can additionally be used in high cycle life applications such as ATE. These sockets support pitches from 0.2 mm to 1.27 mm. Ironwood's GT sockets are ideal for prototyping and testing almost any BGA device application. These IC sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss (1dB at 94GHz) and supports BGA packages with pitches down to 0.2mm was utilized in these sockets. GT BGA sockets are mechanically mounted over a target system's BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry's smallest footprint).
-
product
HES Prototyping Boards
HES™ is a feature-rich family of SoC/ASIC pre-silicon physical prototyping and hardware emulation boards. The family features boards with high-performance devices from either Xilinx (including Virtex-7, Virtex UltraScale, Virtex UltraScale+ and Zynq UltraScale+) or Microchip (PolarFire and SmartFusion2).
-
product
Sensors
Electronic Product Test & Design
Development kit has ideal support for software development, prototyping and depth-sensing evaluation.
-
product
Infrared Array Sensor
Grid-EYE Evaluation Kit
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic Automotive & Industrial Systems has launched this evaluation kit for its Grid-Eye infrared array sensor, which integrates a ”nanopower” Bluetooth Smart module and a microcontroller. The kit is intended for prototyping the Grid-EYE sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS sensor, lens and I2C interface. The integrated Bluetooth module in the evaluation kit, the PAN1740, draws 4.9mA in transmit or receive operating modes, which means it can be powered by coin cell batteries. The IR sensor has 64 thermopile elements in an 8×8 grid format that detect absolute surface temperature without any contact.
-
product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
GHz Elastomer Sockets
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
product
Rapid Prototype Development
Have time to market pressure and need to get a system or assembly or production line up and running quickly? Need to rapidly build out a solution, but don’t want to spend months on building up an architecture? Allow our rapid prototyping team to assist you – whether it is crafting 3D printed mechanical assemblies or a building up a high speed IO interface, you are in very capable hands with the ARC engineering team. Our DSX product, can help support your IP, implement your process or and be the core processing engine for your design, or if a larger system, DSX could be an integral part of your system. PVS, another tool that can help error-proof your assembly process, is ready to go in a flexible, software-centric solution that you can be reconfigured as needed to meet your changing demands.
