Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Simulation Modules For Sensor Simulation
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
PXI Multifunction Reconfigurable I/O Module
PXI Multifunction Reconfigurable I/O Modules feature a dedicated analog-to-digital converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. You can customize these models with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop (HIL) testing, custom protocol communication, sensor simulation, and high-speed control. PXI Express models also include peer-to-peer streaming for direct data transfer to other PXI Express models.
-
product
6U Single VME Slot Intelligent Interface Card
IIB-3910-VME-2C
The IIB-3910-VME-2C is a 6U single VME slot intelligent interface card providing complete STANAG 3838 andSTANAG 3910 test, simulation and bus analysis capability, for two 3838 dual redundant and two 3910 buses, which support optical dual redundant and electrical single redundant 3910 protocols.
-
product
Protocols
Excalibur Systems provides a large selection of board level products for test & simulation, as well as, the embedded environment. Choose from a number of avionic protocols under platforms such as, USB/Ethernet, PC/104, PMC, PCI, Compact PCI, VME and VXI.
-
product
PCI / PMC / CompactPCI Test System
PCITS
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
SAE J1939 API
The J1939 API is a programming interface that allows quick and easy development of J1939 applications on a PC with Windows operating system.The programming interface of the API is based on the IXXAT VCI driver and is therefore available for all IXXAT PC CAN interfaces. Based on the J1939 protocol software from IXXAT, the SAE J1939 API allows complete simulation of J1939 applications on a PC.
-
product
PXIe-7846, Kintex-7 160T FPGA, 500 kS/s PXI Multifunction Reconfigurable I/O Module
784143-01
Kintex-7 160T FPGA, 500 kS/s PXI Multifunction Reconfigurable I/O Module—The PXIe‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7846 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7846 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PXIe-7867, Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
785570-01
Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module—The PXIe-7867 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 18 analog output channels connected directly to the FPGA, you can quickly design for applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7867 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7867 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PXI-7841, Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module
780337-01
Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7841 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
Test Set
ASE2000
The ASE2000 Test Set is a full-featured protocol test unit. It provides the user with a powerful and flexible tool for diagnosing communication problems and testing and maintaining RTU and IED equipment. The test set has three modes of operation, Master Simulation, RTU Simulation, and Line Monitor.
-
product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Multi-Protocol Test & Simulation Adapter for USB or Ethernet
EXC-UNET2/xx
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
Residual Quality Control
Hill Engineering's expertise in residual stress and material performance provides us with a unique opportunity to effectively design and manage production quality programs. For example, a quality system for residual stress in aluminum forgings would provide the means to control, monitor, and certify the residual stress. In general, the quality system seeks to identify key metrics in the manufacturing process, establish a testing protocol for these metrics to qualify the manufacturing process, and then perform either lot-release and/or surveillance testing to demonstrate process stability over time. Process simulation may be used to identify locations for quality control measurements and portable measurement technology like hole drilling may be used to perform quality control measurements inside of a manufacturing facility.
-
product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
PCIe-7820, Kintex 7 160T FPGA Digital Reconfigurable I/O Device
785361-01
The PCIe‑7820 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7820 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-02
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7846 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
PCIe-7841, Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device
781100-01
Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7841 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
Fiber Channel Simulyzer
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
product
Carrier - Virtex 7 W/FMC Site
VPF: 3U VPX
The VPF is a VPX form factor (VITA 46), FPGA processor board designed to meet the needs of challenging, embedded high‐performance digital signal processing applications at a competitive price point. AMD Virtex 7: VX330 and VX690 population options are available. The Virtex 7 FPGA provides impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed‐point and repetitive processing tasks. The VPF FPGA node processes input from the FMC HPC (Vita 57.1) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 4.0GSPS). The VPF is fully compliant with the OpenVPX standard and accommodates the PCIExpress Gen 3.0 communication protocol. Delphi also offers a VPF FPGA Design kit which allows customers to leverage and modify DEG source code, develop within an open architecture, and rapidly integrate FPGA HDL. The DEG FPGA Design kit includes: Source code, simulation test bench and utilities to support custom algorithm development. Embedded Linux, VX Works and Windows software drivers are available. HPC FMC Site, Fully Compatible with all Delphi ADC and DAC FMC Modules.
-
product
PXIe-7865, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
787355-01
PXIe, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7865 features flexibility of timing and synchronization with a user-programmable FPGA for onboard processing and direct control over I/O signals. The PXIe-7865 provides 24 analog output, 2 analog input, and 32, 5V input-tolerant digital I/O channels connected to a Kintex-7 160T FPGA to help you design applications for hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. You can use the dedicated A/D converter (ADC) for independent timing, individual channel triggering, and multirate sampling. Additionally, the PXIe-7865 includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PXI-7953, Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780340-01
Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7852 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7852 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
Interface
RMAC-VME
Designed for laboratory simulation and production test applications, the Modular Avionics Controller (RMAC) is an intelligent, high performance 6U VME product supporting ARINC protocols and other serial communications. As an evolutionary follow-on product to the successful VME-AIC product line, the RMAC-VME provides a single integrated interface to multiple avionics protocols on VMEbus platforms.
-
product
Wireless Protocol Emulation
MAPS
Message Automation & Protocol Simulation (MAPS™) is a protocol simulation and conformance test tool that supports a variety of protocols such as SIP, MEGACO, MGCP, SS7, ISDN, GSM, MAP, CAS, LTE, UMTS, SS7 SIGTRAN, ISDN SIGTRAN, SIP I, GSM AoIP, Diameter and others. This message automation tool covers solutions for both protocol simulation and protocol analysis. Along with automation capability, the application gives users the unlimited ability to edit messages and control scenarios.
-
product
BusTools/1553 BusTools Software Analyzer
Abaco Systems' BusTools-1553 is an integrated, Microsoft Windows-based, application solution for MIL-STD-1553 test, analysis and simulation. BT-1553 software harnesses the power of Abaco Systems' hardware interfaces on PCI, PCI Express, CompactPCI, PMC, ExpressCard, PCMCIA, USB, XMC, PC/104-Plus, VME and VXI platforms for simplified control over simulation, display, data logging, playback, and protocol analysis of MIL-STD-1553/1760 A and B networks.
-
product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
product
ARINC BusTools Software Analyzer
BusTools-ARINC is the only solution for Bus Analysis, Simulation, Maintenance and Data Logging of ARINC 429, 575, 561/6-wire, 717 and CSDB databus protocols. Simultaneously control, log and display data from a single Windows-based program on USB, PCI, CompactPCI, PCI Express, ExpressCard, PC/AT, PC/104 and PCMCIA platforms. BusTools-ARINC provides comprehensive monitoring, data logging and simulation for 100% bus loading activity.
-
product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
