Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
product
Printed Circuit Board
RISER-PCM-1
WINSYSTEMS’ RISER-PCM-1 boards are designed to provide extra space in a PC/104 stack. They are printed circuit boards (PCBs) with PC/104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
Wireless In-Circuit Test Fixtures
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
product
Clamshell Type Mechanical Fixtures
Series 31
The GR Series 31 dual well mechanical kits provide a solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility and the advantage of testing two devices on the same test fixture. These can be similar devices, or devices that are used together in a functional test.
-
product
Electrical Tester Grid Field
TCI can furnish grid spring probes for most Bare Board Electrical Testers in production at most Printed Circuit Board Manufactures. Look for your model of Bare Board Tester in the following list and call TCI for current price quotation.
-
product
SMA Connectors
Pasternack SMA connector category contains a large selection of part numbers, the majority are RoHS and REACH compliant. SMA connector products in this category will terminate to coax, PCB (printed circuit board) or terminal and are built to precise RF and microwave industry specifications. Our SMA connectors are constructed in male or female gender in standard polarity, reverse polarity (RPSMA / RP-SMA) or reverse thread threads, with 50 Ohm impedance. Connector SMA series from Pasternack are available in straight, radius right angle or right angle versions, as well as, press in, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMA designs include clamp/solder, compression, crimp/solder, crimp/solder (captive contact), field replaceable, solder, solder (without contact), solder/solder or solder/solder (captive contact) attachment methods. We offer connectors in SMA series with standard or high performance levels manufactured with brass or stainless steel bodies. Other SMA connector options include quick disconnect (QD) or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMA connector series is in-stock. But not just in stock, also they will ship the same-day as they are ordered.
-
product
Pine Electronics
Specializing in low-mid volume electronic manufacturing services, Pine Electronics, Inc. offers a wide range of printed circuit board assembly (PCB assembly), cable and box build assembly solutions. Our equipment, engineering and technical talent serves both multi-national and regional customers throughout the United States. Known for full-service PCB assembly work, Pine Electronics, Inc. is highly integrated and responsive. Each customer has a designated representative for all commercial and technical questions. This personalized service model enhances communication, expedites project development, and represents Pine’s commitment to customer service.
-
product
Test Fixture Kits
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
product
Software
D2B
The unique capabilities of Teradyne's D2B software enable EMS and OEM manufacturers and partners to interconnect their global enterprises to optimize printed circuit board assembly test and inspection efficiencies early in the manufacturing / build cycle. D2B is a powerful suite of solutions that provides a standards-based architecture that supports GenCAM and ODB++ file formats enabling electronic manufacturers to outperform their competition, maximize profitability, and get to market first.
-
product
Solid State Voltage Injector
J2110A
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
product
Test Fixture Kits
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
product
LC-4.5 Voltmeter
5203
Model LC-4.5 is the first hand-held voltmeter to include a number of special features which facilitate corrosion and cathodic protection testing on underground structures. It is designed for field testing under almost any environmental conditions. Sealed Mil Spec. switches, sealed windows, a gasketed case and a printed circuit board with baked-on moisture and fungus resistant coating on both sides make this possible.
-
product
High Capacitance MLCC Tester
Allegro
Electro Scientific Industries, Inc.
Allegro performs high-throughput production-oriented testing of multi-layer ceramic capacitors (MLCC) and is designed to meet the challenges faced by MLCC manufacturers. Allegro allows customers to verify quality and ensure accurate specifications for the MLCCs used in a variety of applications related to the manufacturing of high-quality printed circuit boards used in nearly every type of electronic device.
-
product
Printed Circuit Board Bending Test Jig
Evaluation of Bending Strength of Electronic Components and Substrates
-
product
ASA101A
The ASA101A Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA101A you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board.With the ASA101A we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at a super-affordable price.
-
product
Single-Inline Package (SIP) Relays
Series LS
Series LS single-inline package (SIP) relays are designed for mounting on printed circuit boards. LS relays facilitate heat sinking by providing an metallic interface surface. The relays use a direct-bonded copper substrate for thermal efficiency, thermal stress performance and long-life expectancy. Optional heat sinks are available.Available options include:LS24D16C 50A, 90-280Vac, 600Vpeak Load; 4-20mA ControlSHP24N50R 50A, 100-280Vac, 600Vpeak Load; 8-30Vdc Control
-
product
1149.1 Boundary Scan Feature, GTE 10.00p
K8212B
Boundary scan is a method for testing interconnections on printed circuit boards. Keysight’s Interconnect Plus Boundary Scan feature enables all the tools required to develop and execute this foundational test method on the board under test.
-
product
Embedded Transceivers
Embedded transceivers are chip-sized components based on 850 nm VCSELs and offer bandwidth up to 300 Gbps for short reach applications (<300 m). These transceivers can be soldered or socketed to a printed circuit board and are well suited for small, compact systems requiring high I/O density, low power, and small space. Many of these transceivers have been qualified to operate in harsh environments, such as the ones found in space, and aerospace and defense applications.
-
product
Extender
3690-2
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
In-Circuit ESR & DCR capacitor Tester
236
This In-circuit ESR & DCR capacitor tester is designed to measure ESR (equivalent Series Resistance) on capacitors range from 0.47uF to 2200uF, in or out of circuit. The ability to trouble shoot in-circuit saves time and makes the 236 a must for anyone that tests or trouble shoots PCB (printed circuit boards).
-
product
Thermal Cycling Test Equipment
Wewon Environmental Chambers Co, Ltd.
IC welding to PCB, IC is integrated in the chip general purpose circuit, it is a whole. Once the inside is damaged, the chip will be damaged. The goal of printed circuit boards (pcbs) is to connect IC and discrete components to form a larger working circuit. Thermal cycling equipment can detect the defects and hidden dangers of welding components in the production process, decreasing failure rate. When it fails, components can be replaced in timehttps://www.wewontech.com/thermal-cycling-test-equipment/
-
product
Filters / Splitters / Detectors
DiCon’s 100 GHz WDM is designed to multiplex and demultiplex signals in multi-wavelength systems based on the ITU 100 GHz grid. The component uses a thin film filter mounted between a pair of GRIN lens collimators. The 100 GHz WDM is housed in a compact, environmentally stable package that offers superior resistance to humidity and temperature and is suitable for mounting on a printed circuit board or within a module.
-
product
LED Lighting Panel Tester
igentic® 821t
Growing demand for light emitting diode (LED) products combined with increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. Sterner Automation, a leader in LED test technology, provides solutions that address these specialized requirements, including the versatile igentic® 821t panel testing system. The igentic® 821t automated process combines advanced vision technology with flexible positioning and power-up capabilities to detect inconsistencies in individual LEDs at the panel production level. The resulting detection capabilities ensure that the highest standards are met while maintaining the capacity associated with today's high speed automated lines.
-
product
PCIe Gen3 4K at 500 Fps High Speed Compact Camera for Testing
CB160MG-LX-X8G3
4K at 500 Fps High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
product
PCIe Gen3 High Speed, Compact Camera for Testing
CB013CG-LX-X8G3
High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
product
PCI Express
PCI Express (PCIe) is a highly successful SerDes interface that is used in computing devices spanning a wide range of applications. Currently in its fourth generation with on-going roadmap development for a fifth generation, the PCIe interface is undergoing major technical advancements that require state-of-the-art development and validation tools. For example, Gen4 PCIe devices operate at 16 Gbps per lane and are expected to deliver very low bit error rate (BER) levels even over constrained and lossy transmission channels (e.g. printed circuit boards).
-
product
PCIe Gen3 4K Compact, High Speed Camera for Testing
CB120MG-CM-X8G3
4K, compact, high speed camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
product
Automated Optical Inspection (AOI)
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
product
PXI-2536, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-36
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
1149.1 Boundary Scan Feature, GTE 10.00p
K8212A
Boundary scan is a method for testing interconnections on printed circuit boards. Keysight’s Interconnect Plus Boundary Scan feature enables all the tools required to develop and execute this foundational test method on the board under test.
-
product
Solid-State Inline (SIP) Four-Pin Relays
Series AS4
Series AS4 solid-state single inline (SIP) four-pin relays are designed for mounting on a printed circuit board. The relays offer built-in voltage protection and can withstand very high current overloads. The relays have a low zero-cross window. The compact size and triac output make the AS relay the perfect retrofit for electromechanical relays. All Series AS relays are Zero-Cross switching.Available options include:AS24D4E/R 4Arms, 12-275Vrms, 600Vpeak Load; 4-30Vdc ControlAS24D4E-X1 4Arms, 12-275Vrms, 600Vpeak Load; 6-30Vdc Control; DIN-rail clip+LEDAS24D4E-X2 4Arms, 12-275Vrms, 600Vpeak Load; 6-30Vdc Control; DIN-rail clipAS46D4E/R 5Arms, 12-460Vrms, 800Vpeak Load; 4-30Vdc Control
