Filter Results By:
Products
Applications
Manufacturers
- Halls Instrumentation.
product
Light Testers
Hall’s have designed and manufactured products for oil, industrial, farming, commercial, and transportation markets. Products such as truck and trailer light testers, bop savers, early engine warning systems, oil spinners, engine control panels, dashes for service rigs, drillers panels, and sandline controls. Halls have been involved with over the rebuilding from scratch of over twenty service rigs.
-
product
Live-dead_Live Meter Verifier
LDL-1100
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 50 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL 1100 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
product
Dual High Voltage Power Supply Tester
MS 1110
DHVPS Tester is used to test and service the dual high voltage power supply units. High Voltages of range from 4KV to 11KV can be tested.
-
product
Test Systems
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
product
FPD Tester Power Module
67393-120-480
The 67393-120-480 FPD Tester Power Module is a new generation of small, stable, high reliability AC to DC power supply. It adopts compact mechanical design and uses Chroma FPD Tester for signal input/output that can provide a total solution for testing the signal, control and power of diversified panels.
-
product
Bi-Polar low voltage power supply board
LVPS
This is our standard power supply board used in many of our testers but also available separately. This board is capable of +/-15v, +10 and +5v outputs. Also contained on board is our standard meter drive circuitry for testing instrument meters, a two-pole relay and an option for a sine/cosine oscillator circuit.
-
product
Cable Tracers
162 CB
Standard Electric Works Co., Ltd
Filter Probe● Works with any Tone Generator to identify wires.● Volume control for increasing sensitivity and adjustable to suit work environment.● 2 operation modes: Filter on / Filter off.● The auto-off function (5 minutes) prevents battery consumption.● Power supply is available in any 9V battery with a life of approximately 50 hours.● A phone jack is designed for headset or handset.● Flashlight function.Tone Generator● Tone Generator is a great tool for locating and identifying cable pairs or individual conductors.● 162 CB-G doesn't only provide the function of a tone generator, but also serves as a continuity and polarity tester.● A tone selector switch located inside the unit for selection of the fast tone or the slow tone.● Two bi-colored LEDs for Line1 and Line 2 indication of the polarities of the telephone lines.● The unit has alligator type terminals, a modular cable of 4 conductors with a strong connector.● The tone and continuity functions are only applied to Line1. (Modular connector)
-
product
Power Functional Test with Energy Saving Solutions
Power System
The Power System is a test platform conceived to verify and certify the operation of power modules.The complete structure, combining two Multi standard cabinets, is sized to contain all of the resources required for testing: drive/sense modules, power modules and load simulators.In this tester, in addition to strictly perform the requested measurement as per technical specifications, the issues of consumptions and dissipations were taken into account, integrating an Energy Recovery circuit which enables reuse of output energy to supply the system.
-
product
Digital Electrical Network Analyzer
2726 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Built-in earth tester.● Built-in loop/psc tester. 0.03-2000Ω (software ctrl).● Built-in voltmeter.● Built-in wiring checker.● One push button smart control.● Display L-N and L-E voltages. 50 to 280Vac (sine).● Display line path impedance. 0.01-2000Ω (software ctrl).● Display earth path impedance. 0.01-2000Ω (software ctrl).● Display neutral path impedance. 0.01-2000Ω (software ctrl).● Display psc line to neutral. 6kA@230Vac supply.● Display psc line to earth. 6kA@230Vac supply.● Re-scroll through previous results.● Bat. ok/low battery indicator.● Auto-off function.● Color coded test leads.● Rugged Case.● Ultra low power consumption.
-
product
CCTV testers
1.IPC Tester ,Support H.264/H.265 4K HD IP Camera.2.POE 48V Power Output,Max 24W;3.Support ONVIF, dahua, Hikivision, ACTi,samsung IPC.4. 4.3 inch 800*400 capacitive screen, image display more clearly;5.Built-in WIFI function,can test the Wi-Fi IP Camera;6.Support IP PTZ control functions (ONVIF).7.Support DC12V1A power supply output.8.Support Audio input test.9.Support 4K HD video files and Screen projection function.
-
product
Battery on-line Monitoring Tester
HD Power Test Equipment Co.ltd
Battery on-line monitoring system tester is a on-line battery monitoring and auto maintain system for USP,EPS, DC power supply, communication power supply . The tester has the function of monitoring and alerting for a series of parameters such as battery pack voltage, battery pack current, cell battery voltage, cell battery internal resistance, battery environment temperature, Cell Battery negative temperature and battery voltage balance, residual capacity and discharge. It can automatically maintain balance voltage, which used for on-line monitoring 2V and 12V battery.
-
product
Electrical Insulation Tester Kit with Dual Display
420001
When undertaking power installations, the 420001-insulation tester can provide special help to test wiring. This unit can provide 125V,250V, 500V and 1000V source for the test, and under each range it can supply 1mA current to feed the capacitance load. With the auto-range function, it can measure up to 4,000 Megaohm with the resolution of 1Kohm.
-
product
EOL/Functional Testing
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
product
Automatic Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
product
Fully Automatic Transformer Winding Resistance Tester
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.Principle: The constant current generated is fed to the resistance under test through the current terminals and the voltage drop across the resistance under test is measured and displayed in ohms. A true four terminal measurement is used to eliminate the need for lead resistance compensation.
-
product
HDCD Battery Charge Tester
HD Power Test Equipment Co.ltd
HDCD Battery Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It keeps the constant communication maintain between the battery charge ensuring a perfect charge.Battery charge tester is designed using intelligent three-stage charging mode to achieve the function of automatic conservation between charging and floating charge. It also can on-line detect the voltage of the whole battery, real-time display and record the voltage of whole battery. The tester can automatically accomplish charging after setting the parameter of voltage, current, time and capacity.
-
product
Franklin Tester Model
Model FT2
Franklin Tester Model FT-2 is designed as per IS:649 & ASTM:717 Standard to measure insulation resistivity of electrical steel sheet. It requires precision & noise free DC regulated power supply and equally distributed pressure on electrode. Franklin Tester FT-2 regulated power supply provides 0.5000V with 0.1% accuracy over load and no load. Most of national and international standard has specified only 0.5%, means FT-2 is equipped with five time better accuracy than required.
-
product
PST-3 Digital Power Supply Tester 20/24pin
Rexus PST-3
ATX PSU each output connectors checkTests 20-pin and 24-pin power suppliesTests SATA powerTests Pentium 4 power connectorTests PCI-Express power connectorsTests Xeon power connectorsTests Floppy drive connectorsTests standard 4-pin power supply connectorsAccurate voltage indicator +/-V(+12V1/+5V/+3.3V/5VSB/+12V2/-12V)ATX P.G value display.Lower or higher P.G values alarmLower voltage detected alarm.Over voltage alarm.No voltage detected alarm.Dimension : H * L *D : 64mm * 150mm * 18mm
-
product
Medical Leakage Current Tester
2675Y
Shenzhen Chuangxin Instruments Co., Ltd.
The 2675Y Medical Leakage Current Tester Series Is The Test Equipment Used For Measuring Continuous Leakage Current And Patient Auxiliary Current Of Medical Electrical Equipment.It Designs And Products According To The GB9706.1_2020 (IEC60601-1:2012) .And The Test Circuit (MD)Input Impedance To Simulate The Body Impedance,It Accord With The Requirements Of GB9706.1-2020 (IEC60601-1:2012),The Test Current Can Run Up To 5A,And Provide Users With An Isolation Power Supply Which Adjustable Output Voltage For 0~250V Continuously Of The Basic Capacity Configuration For The 500VA And Provide Another 110% Voltage Source Of The Maximum Rated Voltage.It Can Satisfy The I,II, Various Types Of Equipment Test The Earth Leakage Current,Shell Leakage Current,Patient Leakage Current,Patient Auxiliary Leakage Current Under Normal Condition And The Single Fault.
-
product
Multi-Channel Power Module
67394
The 67394 Multi-Channel Power Module is a new generation of compact, stable and high reliability AC to DC power supply that can test the small size panels. It has multiple power sources with voltage/timing adjustable functions, protection functions and measurement circuits. Its modular design can work with FPD tester and PG card to provide standard power source for testing the panels.
-
product
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KG
FM-204M50KG
Guangzhou Landtek Instruments Co. Ltd.
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KGApplications:Making job task analysis and ergonomic analysis simple and accurate, it is ideal for workplace design, strength assessment and ergonomic research.Details:Force Rang:±50kgf,±490N,±110LbfResolution:0.01kgf,0.1N,0.1LbfAccuracy:±0.5%FS ± 1DigitUnit:kgf, gf, N, LbfMeasurement State:Peak Value Measurement, Real Time MeasurementDisplay:2 Reversed 4 Digit LCDPower Off:10 Minutes Auto Power Off, Manual Power OffBacklight:BacklightSafe Load:150%FS (Buzzer Alarm Over 110%FS)Power Supply:2x1.5 AA(UM-3) Battery or 5VDC Power SupplyOperating:0°C~40°CConditions:< 80%Surrounding:No Vibration Source or Corrosive Medium AroundWeight:705 gSize:host machine:170mm*72mm*35mmhandspike:315mm*Φ30mm Instrument stents：155mm*95mm*35mmAccessories:Standard Accessories:ManualCarrying CaseInstrument stents4 M3*18 screwsE-1005Optional Accessories:External USB power supply cableE-1004For quotation please feel free to contact Lisa Li. Thank you.
-
product
Battery Discharge and Charge Tester
HD Power Test Equipment Co.ltd
Battery Discharge Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It can proceed the discharge and charge for the batteries to extend the lift-time.
-
product
Phase Sequence Meters
Phase sequence meter is used for detecting the sequence of the supply in three-phase electric circuits. Since the direction of rotation of three phase electric motors can be changed by changing the phase sequence of supply. And also the correct operation of measuring instruments like 3 phase energy meter and automatic control of devices also depend on the phase sequence. Different types of phase sequence testers are available in today’s market like contact or non contact, static or rotating, etc., in a wide range of voltage or power ratings.
-
product
Rail Pressure Tester
RPT-5
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
product
Portable Power System
portable power system is a portable emergency power supply system specially developed by our company using high-capacity lithium-ion battery system for power operation and maintenance. It can provide emergency and standby power supply for automation devices such as protection devices and commissioning tools such as relay protection tester.
-
product
Handheld Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The hand-held Circuit resistance tester is an innovative product. The product is compact, hand-held operation, battery power supply, easy to carry. The product is mainly used in the measurement of contact resistance and other micro-Euclidean resistance of switch contacts. The test speed is fast and the accuracy is high.
-
product
Ground Leads Continuity Tester
Weshine Electric Manufacturing Co., Ltd
1. The new power supply technology is adopted in the grounding down lead conduction tester.2. It has the characteristics of small size, light weight, large output current, good repeatability, strong anti-interference ability and protection function. 3. The whole machine is controlled by single chip microcomputer, which has a high degree of automation. 4. The instrument has high precision and easy operation. The maximum current is 10A.
-
product
Live-Dead-Live Meter Verifier
LDL-1200
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
product
Test System
LB301
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
product
Vibration Unit Tester
BK2020B
We developed the BK2020B as an upgrade to our BK2020 to test the electrical specifications (RPM, current, drop pulse, start up voltage) of your cylindrical or coin type vibration units. You can also test vibration level, noise, isolation resistance, and the DC resistance. The DUT power supply and all measurement components are self contained, so external devices aren't needed and the tester uses DSP, making it capable of fast, highly accurate and reliable measurements. The BK2020B is very versatile. It can be set up as a stand alone machine, or used with a PC and software for access to more information, and to save the data for analysis. Either version is great on the product line but you may also use it for QA, QC and development.
-
product
Power Supply Tester
UTS-625
The UTS-625 provides the ultimate in ATE flexibility. Its open-ended architecture allows users to custom configure the Autotest system to meet the needs for one or multiple applications. Housed in standard full size racks, the UTS-625 system may be expanded from a single bay to multiple bays as required.
