Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A
40-667C-012
The 40-667C-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Multi Function Automobile Tester
6521
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance and power providing testing.
-
product
High Speed Response, High Accuracy DC Leakage Current Sensor
DCZCT-20CDHL
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Low DC current measurements.*DC1mA～200mA*High accuracy.*±1%F.S ±10mV*Least influence of magnetization.*Less than DC1mA in current level*Convenient +5V single polarity power supply.*Reference voltage (Vref) terminal is equipped.
-
product
High Voltage Probe
HVP-40M
*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010
-
product
20kV 4 Collector Test Set
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process.
-
product
Digital Panel Meter
ST-312V (ST-312mV)
Standard Electric Works Co., Ltd
● 3 1/2 digit liquid crystal display.● 200mV and 2V full scale input sensitivity.● Single Battery operated 9V supply or ±5V DC power supply (Dual supply).● Built-in low battery indication and automatic polarity indication.● Decimal point selectable.● Low power dissipation Typically less than 20mV.● High input impedance (> 1M ohm).● Guaranteed zero reading for 0 volts input on all scales.● True differential input or single-ended input.● Self mountable with optional mounting bezel.● Low cost high performance.● EN 50081-1 EN 50082-1 EN 55022 EN 61000-4-2 IEC 801-3
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
Power Analyzers
At PCE Instruments you will find a power quality analyzer to measure the power in W, kWh or to analyze and measure harmonics. This power analyzer is a multi-function power analyzer device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power. The reading of AC power is considered the real value and has a maximum range of 6000 Watts. While a reading is being taken, the polarity changes automatically, if negative values are taken then a minus sign will appear on the device display.Nowadays, power quality analyzers have many features such as, insulated current input, measurement of harmonics, AC and DC current measurement, AC and DC voltage measurement, frequency measurement, phase rotation measurement and idle, apparent and effective power measurement. All this data can also be logged and analyzed with the delivered PC-Software. Power analyzers of the type PCE PA 6000 can determine the energy in single-phase systems.Power quality analyzers of type PCE-GPA 62 allow the energy measurement in symmetrically loaded three-phase systems. Power analyzers of type PCE-PA 8000, PCE-360 and PCE-830 support professional power and energy measurements in single and three-phase systems.Apart from being used as energy-measuring devices, power analyzers like the PCE-830 can also be used for network analysis and the determination of harmonics and phase rotation. On our website you will find other power analyzers used in the field of electronics.
-
product
High Frequency Current Transformer
HFCT Ø 140mm
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
product
Passive Component ATS
Test and packing speeds from 80ppm to1,800ppmStandard functions - Inductance/quality factor test - Winding resistance test - Polarity testOptional functions - Layer short test - Insulation resistance test - Bias current testCircular vibrating plate design feeds inductors steadily and rapidlyIndex disc design eliminates dropped inductorsFour-wire measurement test socket designAutomatic discharge mechanism when feeding errors occurEach test station has an independent NG (No Good) product collection boxTest without packaging function provided, good products gathered in bulk collection boxExclusive data collection software designed for monitoring product quality in real timeReserved stations for number spraying and automatic optical inspectionSwitchable Chinese/English/Japanese operating interfaceEquipment is fast, stable and safe
-
product
SMA Connectors
Pasternack SMA connector category contains a large selection of part numbers, the majority are RoHS and REACH compliant. SMA connector products in this category will terminate to coax, PCB (printed circuit board) or terminal and are built to precise RF and microwave industry specifications. Our SMA connectors are constructed in male or female gender in standard polarity, reverse polarity (RPSMA / RP-SMA) or reverse thread threads, with 50 Ohm impedance. Connector SMA series from Pasternack are available in straight, radius right angle or right angle versions, as well as, press in, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMA designs include clamp/solder, compression, crimp/solder, crimp/solder (captive contact), field replaceable, solder, solder (without contact), solder/solder or solder/solder (captive contact) attachment methods. We offer connectors in SMA series with standard or high performance levels manufactured with brass or stainless steel bodies. Other SMA connector options include quick disconnect (QD) or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMA connector series is in-stock. But not just in stock, also they will ship the same-day as they are ordered.
-
product
Voltage/Continuity Tester
VOT-50
Standard Electric Works Co., Ltd
● Voltage test: 12V to 690V AC/DC (7 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 127V, 230V, 400V, 690V.● Polarity test: LED +/-● Audible continuity test● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP54● Phase / Neutral identification● Integrated storage clips for test probe.● Rubberized injection molding.
-
product
Long-range Surveillance Thermal Imaging Camera
IRT303
Wuhan JOHO Technology Co., Ltd
Long-range Surveillance Thermal Imaging Camera IRT303IRT303 is extremely compact, durable uncooled day/night system, operating in 8-14 um waveband, with DDE image processing technology and high sensitivity, it is ideal for quick and accurate situational awareness in a variety of defense and security applications. It specially equipped with Dual-FOV, the wide FOV for find object in wide scope and then fast switch to narrow FOV looking at the target for details. IRT303 is the optimal device for super long observation purpose and target acquisition.ApplicationsLong distance surveillance or patrolLand border and coast surveillanceMarine navigation or rescueTechnical DataDetector Detector material Uncooled FPA Spectral range 8~14 m Pixels 320x240 Pitch 38 mx38 m NETD 50mK@25 C (f/0.7) Optics Lens 135mm/45mm FOV 5.2 3.9 /15.4 11.6 Focusing Motorized Optional lens 100mm/25mm, 120mm/40mm, 150mm/50mm, 180mm/60mm Image Presentation Video output 25Hz PAL/30Hz NTSC Electronic Zoom x2 Polarity BH/WH inverse Brightness & Contrast Auto/ Manual Gain Composition Auto/ Manual Power system Power supply 110~240VAC 9~14VDC (typical: 12VDC) Interfaces Command interface RS232 /RS485/ RS422 alternative Digital video interface(Optional ) Ethernet/LVDS/CameraLink Environmental Ambient temperature -40 C~+60 C Storage temperature -45 C~+60 C Range Performance Detection Range (2.3mx2.3m vehicle) 5500m Recognition Range (2.3mx2.3m vehiclet) 1800m Detection Range (1.8mx0.5m human) 2200m Recognition Range (1.8x0.5m human) 580m
-
product
SNAPSHOT
PH-200
The Snapshot cable checker gives professionals and layman the ability to check cables instantly upon plug-in, with no buttons pressed or displays read. With its built-in memory, the Snapshot simply checks each cable plugged in against a correctly-configured cable pre-set by the user, and indicates the cable’s status with a sound. For pin-by-pin cable checking, the 〝standard check〞mode offers a plain LED-displayed check of the cable’s pins, checked automatically or manually. The Snapshot also generates a tone along the length of cables, making finding and following the cable with a tone probe a snap. A remote unit allows testing of already-installed cables, and a built-in line tester verifies phone line polarity and detects voltage before it threatens the safety of the test unit. A shield-test feature automatically tests cable shielding and a battery-low indicator prevents misreading results.
-
product
Network Cable Tester
PHCT45
This Pyle network cable tester checks RJ45 and BNC network cables for continuity and correct polarity. LEDs show the status of each pin. , perfect for the IT guy on the go.
-
product
Resistivity Meter with Multi Electrode
POLARES
Till this moment the use of Electrical Resistivity Tomography (ERT) for geology has always been basically the same since its debut, based on the original vertical Electrical Soundings (VES) principles: applying a continuous current to two stakes inserted into the ground and measuring the corresponding voltage between other two. The applied current and thus the relative tension have always been continuous, with an inversion in polarity for each measure. The new tool POLARES uses an alternate current, instead, sinusoidal type, with an adjustable frequency.
-
product
Socket Testers & Adaptors
Our range of socket testers & adaptors allow users to quickly and simple check the wiring of a socket, clearly identifying polarity faults with and audible buzzer continuously sounding if correct.
-
product
Multi-Purpose Digital H. V. Phasing Meter
MDP-50K
Standard Electric Works Co., Ltd
● AC 50kV and DC 50kV measurement with direct reading.● 4000-count LCD.● Input impedance : 400 Mohm● Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV DC : 4.000kV / 40.00kV / 50.0kV● MDP-50K must be connected with an approved hot stick, such as HS-175, HS-120.● Polarity indication : Positive / Negative● Backlight function.● Auto power off.● Power source : 1.5V(AA) alkaline battery × 2.● Low battery indication(Multi-level). ● Protection class : IP66
-
product
DC Gaussmeter
GM1-ST
The Model 1-ST measures strength and polarity of magnetic fields up to 19,999.9 gauss. The sensor can easily fit in a .060 inch (1.5 mm) gap and is at the end of a 100 cm flexible cable. The sensor end can be bent if required for a variety of situations. Place the sensor on a magnet face to measure the field. With a resolution of 0.1 gauss, it can measure any tiny variation from magnet to magnet or it can detect if a given magnet has lost even a little strength. Bend the sensor in to a "L" to measure inside a DC solenoid tube. The 5 digit display requires neither auto nor manual range change, making it easier to use than older style 3 or 4 digit meters. Turn on the meter and immediately begin reading fields (updates 4 times per second). There is no setup required, making this the fastest, easiest gaussmeter available.
-
product
High-Voltage Test Device
PGK 70 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
product
Digital I / O modules
The 34950A module has 64-bit bi-directional lines and can be configured with 8 8-bit digital I / O channels with handshaking capability. Each 8-bit channel has programmable polarity and a threshold of up to 5V. The memory can be used to generate or capture digital patterns up to 10 MHz. It provides seven configurable handshaking protocols for a wide range of applications. In addition, two counter / totalizer channels can be used to compute events, frequency, period, duty cycle, accumulation, and pulse width.
-
product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
-
product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Voltage Touch Monitor
The AlphaLab Voltage Touch Monitor enables personnel to identify voltage problems that usually remain hidden. The monitor reads the voltage on a finger (which is identical to the voltage at every other point on the body). It can detect as little as 1/10 volt in two modes: DC and AC/Spikes (ESD transients). In the DC mode, the displayed voltage is either positive or negative, and is usually very low if grounding is being worn and is functioning properly. Higher DC voltages (even while grounded) occur if a DC ionizer is blowing too close or if the person rubs against a high-static material or comes in contact with metal at a DC potential. If personal grounding is not being used, any DC signal can build up over time, and the DC mode continues to show the instantaneous body voltage as it changes. In the AC/Spikes mode, any transient voltage spike at least 1/2 millisecond long is temporarily displayed. If there are several consecutive spikes, only the highest is displayed, regardless of polarity. If the signal is a repetitive (AC) wave, the peak voltage is displayed, but always as a positive number. Even when proper grounding is worn, several tens of volts often occur with transients and AC. Maximum error for DC and AC is only 2% of the reading +/- 0.1 volt.
-
product
Minirator
MR-PRO / MR2
The Minirator MR-PRO provides a full set of analog audio signals including sine wave, pink noise, white noise, delay test signal, polarity test signal, stepped sweep and continuous sine sweep. Further, a set of wav-files, useful for system optimization, is stored in the internal flash memory. Add your own personal favorites to this set.
-
product
Digital Display Auto Circuit Tester
1676
Peaceful Thriving Enterprise Co Ltd
This is a DC voltage tester with smart over-voltage protection and warning for vehicle repair. As electrical system for vehicle becomes more complex, the tester is able to test voltage value, identify DC polarity from different background light color, positive / negative sign, and over-voltage level indication. Moreover, the special designed probe is able to help user to hook, piercing, and probing the wires.
-
product
Digital ELCB (RCD) Tester
1812 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2Lines × 16 Characters LCD.● Very low consumption.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Zero Crossing Circuitry permit testing at 0° or 180°.● Disconnection Phase Polarity shown on LCD display.● Auto-off and off override.● Polarity Trip indicator (Positive of Negative Phase).● Wiring polarity indicator.● Measure voltage and frequency between Line and Earth before testing.
-
product
PXI Solid State Multiplexer, 30 Amp, Dual 3-Channel
40-667A-011
The 40-667A-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Digital Multimeter
DT-1000
4 1/2 digits LCD with max. reading of 1999. Auto polarity indication. Low battery indication. Data hold function. Diode & Transistor test. Size: 172¡Á88¡Á39mm
-
product
System Control Modules for 34980A
The 34980A System and Control modules provide additional measurement and control capabilities that are typically used in test applications. Choose from modules that include digital I/O with programmable polarity, D/A converter with onboard memory to create waveforms, and frequency counter/totalizers.
-
product
Substation Tester
JYH
JYH C CT PT Analyzer,full-featured, can not only satisfy the test requirements of various CTs (include TP class), such as the excitation characteristics (i.e., volt-ampere characteristics), ratio, polarity, secondary winding resistance, secondary burden, ratio error and phase displacement, but can also be used for the tests of various PTs, including excitation characteristics of the electromagnetic unit, ratio, polarity, secondary winding resistance, ratio error and phase displacement.
