Filter Results By:
Products
Applications
Manufacturers
- Applied Instruments, Inc.
product
Return Band Alignment System
6103/6106
Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106).
-
product
Precision Programmable Attenuator
RCDAT-30G-30
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
product
Rackmount or compact airborne state of the art Solid State Power Amplifiers
SSPAs
Broadband off the shelf or custom designed RF/Microwave SSPAs as airborne baseplate miniature modules or as 19" 3U compact rackmount AC units, CW or Pulsed operation from 100W to 1KW up to Ku frequency band.
-
product
Ku Band Gain Control Amplifier
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
product
MICROWAVE TUBES
High reliability dispenser cathode technology (up to 90,000 hrs operation achieved for S band Watchman ATC radar)European “Centre of Excellence” for cathode and electron gun designIn-house cathode technology minimising reliance on ITAR controlled partsFast warm (under 3 seconds) versions available in Ku bandEmission testing and surface analysis facilities in-houseAir, land and sea platforms supported
-
product
Waveguide Electromechanical Relay Switches
Pasternack's waveguide electromechanical relay switches offer full waveguide performance covering C, X, Ku, K and Ka frequency bands. Waveguide electromechanical relay switch components from Pasternack cover various frequency ranges from 5.85 GHz to 40 GHz depending on the model. These waveguide switches are ideal for applications that include electronic warfare, electronic countermeasures, microwave radio, VSAT, SATCOM, radar, research and development, space systems and test instrumentation.
-
product
Signal Level Meter
XR-3W+
From satellite dish alignment, to UHF off-air antenna pointing, to cable TV MER measurements, the XR-3 is the meter for you! The XR-3 is the most capable meter offered by Applied Instruments. It's more durable than the popular Super Buddy meter, and has added features and performance. The XR-3's modular design with field swappable modules provides wide versatility to fit different measurement applications, including DBS satellite (i.e. Dish Network, DIRECTV, Bell TV, Shaw Direct), VSAT satellite (i.e. iDirect, Hughes Ku band, and more), VHF/UHF off-air (analog and ATSC digital), and CATV (QAM and analog). The XR-3 is great for installing and troubleshooting DISH SmartBox, Blonder Tongue, and other SMATV headend systems often used in hotels, multi-dwelling units, and institutional facilities. Modular Test Instrument. Satellite Finder. Installer Signal Meters. CATV Analyzer. Modules.
-
product
Waveguide Electromechanical Relay Switches C, X, Ku, K & Ka Bands up to 40 GHz
Waveguide Electromechanical Switch models cover C, X, Ku, K, Ka frequency bands up to 40 GHz. SPDT and Optional DPDT* Configurations with Latching Self Cut-Off Actuators, TTL Logic, and Position Indictors with manual override. Patented Motor Drive with Arc Suppression. Designs support WR-137, WR-112, WR-90, WR-75, WR-62, WR-42, and WR-28 waveguide sizes with O Rings for pressurized operation. Power handling capability up to 12 kW CW and 320 kW Peak. These waveguide electromechanical relay switches deliver desirable performance that includes high isolation levels up to 105 dB, and extremely low insertion loss down to 0.01 dB.
-
product
Fixed GEO Earth Stations
Kratos Defense & Security Solutions, Inc.
Kratos provides a broad range of fixed earth stations ranging from 3.5m to 18m and configured in receive-transmit or receive-only mode. These antennas offer outstanding electrical performance and exceptional versatility to support low PIM at certain Ku bands and all X-band systems.
-
product
Satellite Trunk Interception System
Satellite trunks in the X, C, Ka, Ku bands carry enormous information, the interception of which can assist LEAs with real-time analysis of data transmitted over these links. Our solutions are customizable and scalable (Bands and protocols) based on the customer's needs.
-
product
Universal Band Decoder
Bandmaster III
The Bandmaster III universal band decoder is a highly integrated unit that not only decodes band information using YAESU “band data” (note 1), but can sense band information for all bands from160M through 6M, including 160M, separate 80M and 75M, 60M, WARC bands and 6M by monitoring CAT (note 2) data going to and from the radio. The Bandmaster III also contains all circuitry for level conversion thus eliminating the need for a separate CAT radio interface (note 3).
-
product
Dual Band Radiometer
UVS-AB-T
The UVS-AB-T measures UV-A irradiance and UV-B irradiance.The dual band UVS-AB-T measures the irradiance in two spectral bands with a single sensor providing separate outputs for each band
-
product
Band Pass Filters
High-Pass (HPF series), Low Pass (LPF series) and Band Pass (BPF series) Filters are available, providing desired skirt selectivity and rejection levels with minimum insertion loss in the pass band. The filters are offered in all standard waveguide bands covering 18 to 400 GHz depending on our possibility to fulfil the customers' requirements. Dimensions of filters depends on required specifications. .
-
product
Narrow Band Filters (Single Octave)
IMF™ Series
The Integrated Microwave Filter or IMF™ Series introduces accelerated tuning speeds packed in a very small, lightweight filter, providing maximum sensetivity and improved system performance for cleansing your ESM environment. Designed for the military radar market, specifically Active Electronically Steered Arrays (AESA) Radars and Phased Array Radars but compliment a broad range of applications such as; Commercial, Tactical & Military Communications, RF Front Ends (RFFE’s), SATCOM-on-the-move (SOTM), along with Electronic Warfare & Radar applications.
-
product
Antenna, Octave Band Horn
EM-7020 | 1 GHz – 2.5 GHz
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
product
Low Noise Dual Band VCO
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
product
L-Band Red/Blue-Band Pass MWDM
WD1616/R, WD1616/B
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1616/R, WD1616/B is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to the combination and separation of L-Band, Red-Band (1589~1603nm) and Blue-Band (1570~1584nm).
-
product
Wide Band Transcorders
WBT Series
A fully self-contained RF recording and playback system. A single unit can record up to 40 MHz of RF spectrum between 50 MHz and 6 GHz. The recorded data is streamed to a high-speed, internal 1TB solid state drive. The data files are an industry standard open format VRT and can be played back anywhere within the same tuning range at the same recorded power level without additional equipment.
-
product
C+L Band Broadband Light Source
S-103
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
-
product
Full Band Phase Shifters
STP-18-10-M2
Full band phase shifters are micrometer-driven, waveguide-based phase shifters. The configuration of the micrometer-driven phase shifters is similar to that of level setting attenuators, where the phase shifting is caused by an E-plane dielectric insert in the rectangular waveguide. The amount of phase shifting is directly dependent on the volume of the insert. The VSWR and the insertion loss of these phase shifters are dependent on the frequency. The below standard offering covers the frequency range of 18 to 110 GHz and a phase shifting range of 180 degrees. These micrometer-driven phase shifters are typically used to introduce a certain amount of phase shifting when the absolute number is not a focus.
-
product
O Band Tunable Laser Source
CA9812
The CA9812 O Band tunable laser integrates a widely tunable laser with a semiconductor optical amplifier (SOA). The tunable laser is electronically tuned and can address any wavelength from 1265.00 nm to 1365.00nm. The integrated SOA facilitates flexible control of the output power and acts as a shutter when reverse biased, enabling dark tuning between channels. The device is packaged into a standard module box package, with an ternal optical isolator and a polarization maintaining fiber output.
-
product
Octave Band Analyzer
Octave Band Analysis and AnalyzerOctave band analysis is an indispensable tool for sound measurement because it gives a close approximation of how the human ear responds. Dewesoft octave band analyzer meets all of the IEC and ANSI specifications for octave filters.
-
product
Dual Band Image Intensified & Thermal Weapon Sight
MilSight® S140-D
Designed to mount on any MIL-STD-1913 rail interface forward of an existing scope, the MilSight® S140-D ADUNS (advanced dual-band universal night sight) offers ultimate mission flexibility. Use as a thermal weapon sight, on a spotting scope for long-range reconnaissance, or as a handheld observation device. The ADUNS system offers high-resolution blended thermal and image intensified night vision that provides crisp imagery through total darkness, fog, smoke, dust, and many other obscurants.
-
product
Wide Band Filters (multi-octave)
HF-ERF™ Series
The HF-ERF™ is an internally switched 3‑band, low cost, miniature, high performance tunable filter. The HF-ERF™ was designed to have the best insertion loss and Q in the smallest package possible, 2.0” x 2.78” x 0.6”. All HF-ERF™ filters are fully tested and aligned by Pole/Zero for convenience and ease of use. Both SPI and Parallel control interfaces are available in one filter. Modified variants are available upon request.
-
product
Full Band Down-Converters
STC-20-10-S1
Full band down-converters are designed to convert high frequency millimeterwave signals down to the baseband at 10 MHz to 1.6 GHz. These down-converters deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade components, such as multipliers, amplifiers, filters, isolators, and more. The below standard offering covers the frequency range of 26.5 to 170 GHz and delivers a typical LO power of 3 dBm and conversion gain of 20 dB. The down-converters provide low harmonic levels and excellent gain flatness, making them ideal for test instrumentation applications. Specifications other than those listed below are available upon request.
-
product
L Band Splitter, DC Block All Ports
PD5132
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
L Band Splitter, DC Block All Ports
PD5032
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
product
2 Vertical Multi Band Phase System
W9AD
The system will produce a broadside pattern and an end fire pattern figure 8 as well as other lobes and nulls in the various directions as you change the combinations. One should model this antenna using EZNEC or some other antenna modeling program to determine the patterns which are available to the user on all bands of use.
-
product
Antenna, Octave Band Horn
EM-7022 | 4 GHz – 10 GHz
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
product
Narrow Band Filters (Single Octave)
MINI-SMT® Series
The new MINI-SMT™ tunable filter advances our popular MINI-POLE® Series by providing Surface Mount (SMT) capability along with the field proven RF power handling, low distortion and exceptional selectivity performance of our MINI-POLE® filters. MINI-SMT™ bandpass options are available from 700 MHz to 3 GHz.
-
product
Wide Band Filters (multi-octave)
MINI-ERF® Series
The MINI-POLE® Extended Range Series of tunable filters was developed to address applications needing a small, surface mount package with wide tunability. This tunability is accomplished by the use of multiple internal tunable filters along with high performance PIN diode RF band select switches all contained in one housing. The tunable filters are designed to minimize size and power consumption while maintaining high RF power handling and linearity characteristics. Parallel or serial digital interface can be selected by a mode pin for ease of integration into your design.
