Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
ITA, G10x, 15 Module, Removable Backshell, Keying Feature
410104773
The adaptable G10x ITA integrates a wide variety of I/O options in various module configurations that allow engagement of up to 3,200 signal contacts. The G10x ITA has a removable backshell that also reduces electromagnetic interference.
-
product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
product
Vantage PRO2 Davis
6152 & 6152C
*Refresh Rate – A packet of data is sent from the outdoor transmitter to the receiver every 2 1/2 seconds! This means when you look out the window and see the wind blowing, the weather station will reflect it almost immediately.*Transmission Distance (wireless models) – The first in its consumer price range to use frequency hopping spread spectrum radio technology, the Vantage Pro2 can transmit and receive data up to 1000′ (300 m) line of sight. This is a much greater distance than most other weather stations. This technology also provides improved reception through multiple walls and greater immunity from RF interference.
-
product
Material Compatibility Test System (MCTS)
Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:
-
-
product
ITA, ICon, EMI-Shielded, With Threaded Coupling Adapter And Protective Cover
410123102
The iCon EMI has many of the standard features of the iCon, in addition to Electro-Magnetic Interference protection. The EMI shielding effect on the iConEMI ITA is provided by the stainless steel fibers in the removable plastic cover and threaded metal coupling adapter. The opening of the threaded coupling adapter provides clearance for a maximum cable bundle with an oblong bushing effective diameter of 1.37 in. Protective cover included.
-
product
Impedance Stabilization Network
Beijing KeHuan Century EMC Technology Co,.LTD
KH8158 is a device for measuring the common mode interference voltage of unshielded twisted pair cables. Cable testing according to CISPR 16-1-2. The equipment under test (EuT) and auxiliary equipment (AE) are directly connected to the corresponding ports. The port adopts RJ-45 socket (the distribution conforms to T568A/B.) This equipment is divided into three specifications: CAT3, CAT5, and CAT6, and the corresponding equipment is selected according to the cable model.
-
product
EMI Shielding
Parker Chomerics electromagnetic interference (EMI) shielding product family spans a wide variety of uses and applications, including an extensive selection of EMI gaskets, shielded windows, shielded honeycomb air vents, cable shielding products, grounding solutions, shielding laminates, and metal foil tapes. It also includes conductive adhesives, coatings, sealants, greases and inks, as well as conductive plastics.
-
product
Digital Broadcast Analyzer
Spectrum Analyzer: 9 kHz 4 GHzInterference Analyzer with Interference MappingHigh Accuracy Power Meter, 2-port Transmission MeasurementsCoverage Mapping, Channel Scanner, GPS, AM/FM/PM Analyzer3GPP, 3GPP2, WiMAX, signal analyzersTracking Generator: 500 kHz 4 GHzDigital TV ISDB-T, DVB-T/H analyzersCPRI RF MeasurementsField-proven design: Three-hour battery life, rugged, compact, lightweight, daylight viewable displayIntuitive menu-driven touchscreen user interfacePIM Alert (a downloadable easyTest script)Standard three-year warranty (battery one-year warranty)
-
product
PXI Vector Signal Analyzer
PXI Vector Signal Analyzers feature a wide frequency range, real-time signal analysis, and advanced signal processing. PXI Vector Signal Analyzers can perform measurements for a broad range of wireless technologies such as GSM, EDGE, WCDMA, LTE-Advance Pro, 5G, Wireless LAN, and Bluetooth. Select models also feature a LabVIEW-programmable FPGA that you can customize for advanced measurement applications. PXI Vector Signal Analyzers are ideal for microwave test, wireless test, RADAR test, spectral monitoring, software-defined radio (SDR), radio monitoring, interference detection, signal intelligence, and other applications.
-
product
Optical Wavelength Meter
Optoplex Optical wavelength meter (OWM) uses proprietary thin-film interference filter in conjunction with Fabry-Perot cavity technology combined with a micro-actuator and high-speed electronics. Its working principle is schematically shown below. By comparison with Optical channel monitor / Optical performance monitor, the proprietary wavelength reference unit is introduced to ensure high precision wavelength measurements. Optoplex Optical wavelength meter is the only DWDM wavelength meter capable of measuring wavelengths of multi-lasers in DWDM networks over C-band and L-band wavelength range with a high accuracy better than that the wavelength locker can provide. For example, the device can simultaneously report 80 wavelength values of 80 channels at 50 GHz channel spacing with the wavelength accuracy ± 2 GHz. DPRAM, RS-232, or USB interfaces are available and OWM can be customized to meet specific requirements.
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Quantum Accelerometer
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
product
EMI/EMC Testing
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
product
Electromagnetic Interference Analysis Program
EMI Analyst™
EMI Analyst (U.S. Patent # 7,222,033) is the premier tool for ascertaining compliance with EMI requirements imposed by regulatory agencies.EMI Analyst is an electromagnetic interference analysis program that combines all four facets of EMI analysis into a single design package.
-
product
Artificial Power Network
KH3765
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3765 artificial power supply network is equipped with the receiver produced by our company to conduct large current conduction interference test. The frequency range of this product is 150KHz-30MHz , the current is 50A , and the AC frequency can reach 0-400Hz . It is widely used and convenient to switch. Compared with similar products on the market, it greatly reduces the operation steps and buys valuable time for your rectification work. This product also provides a standard10AThe interface makes your test more convenient. Meet the requirements of GB-6113 for power supply network.
-
product
Audio Line Drivers and Receivers
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
product
Filtered DC Interface Module
DC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of DC power.
-
product
HDMI Interface Module
HDMI modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the HDMI link untouched.
-
product
USB 3.1 Interface Module
Super speed “USB 3.1 type C modules” for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for USB 3.1 link untouched.
-
product
IR Carbon and Sulphur Analyzer
LD-LCSA-A12
IR Carbon and Sulphur Analyzer LCSA–A12 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and 10 to 30 °C, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 32-bit sampling improves sensitivity and accuracy.
-
product
Two Way Monitoring and Control
The Drexelbrook 560 DRX Series wireless products feature 900KHz frequency hopping, spread spectrum technology to provide a reliable, license free, wireless link between the field instrument and the control room.These wireless interface products provide a cost effective alternative to expensive hard wired connections.Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference.
-
product
Active Dual Loop Antenna
KH30936
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
product
8-Ch SPST 12A-250VAC 24VDC Multiplexer with CAN
H620047C2
This module is ideal for switching up to 12A. Composed by eight relays organized in two trees of four with two relays with NC contact available. The module is shielded in order to reduce the radiated interference in high current switchings.
-
product
Interferometers
An instrument in which the interference of two beams of light is employed to make precise measurements.
-
product
Temperature Data Logger
The temperature recording in a process is the most common and widely required application in any process. The commonly used temperature sensors are RTD Pt100 / Pt1000/ Cu53 / Thermistors and different kinds of Thermocouple. In order to avoid electromagnetic interference, the temperature signal is converted to 4-20mA and is carried to the logger. Our range of Temperature Data Logger includes Temperature Humidity Logger, RTD Data Logger, Thermocouple Data Logger and Flameproof Data Loggers.
-
product
Optical Oxygen Sensors
The analyzer is suitable for direct field installation (NEMA 4X) in hazardous area (Class I, Division 2). The optical fiber sensor platform allows small inline sensors to be installed into sample tubing lines (1/4”), flow cells using NPT fittings, or directly into tanks or process lines using our retractable “hot tap” sensor design. BOS optical oxygen sensors are impervious to typical O2 poisons (H2S) and interferences (combustibles, magnetic, CO2 and H2) with high accuracy and long-term stability measurements without the need for complex or advanced sample conditioning systems. The threaded version of the optical sensor has optional Dual Seal (ANSI/ISA 12.27.01) classification for high pressure applications up to 1200 PSIG (82.7 BAR).
-
product
FieldFox Handheld Microwave Signal Analyzer, 44 GHz
N9961B
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
product
Interference Locating System
SeeWave®
Interference impacts wireless network coverage and quality of service, but hunting interference in the field can be expensive and time-consuming. PCTEL’s SeeWave® interference locating system enables a single user to accurately detect the interfering frequency and locate its exact source.
-
product
High Voltage Ammeter
Ampstik®+
Use the Ampstik+ to safely take accurate current measurements when performing high voltage live-line load checks for balancing, switching, or breaking load. This high voltage ammeter measures in every electric utility setting with a linear current sensor to accurately measure .5A to 5000A, while in voltage environments up to 500kV. The opening of the amp sensor is electronically closed, while external currents are electronically rejected. This design enables the user to measure an individual conductor within close proximity to adjacent conductors without interference errors.
-
product
PXI Waveform Digitizer
PXD731x/70xx
Digitize high-resolution waveforms with the fully isolated PXD Series digitizers. Minimize interference and measure "in-circuit" within circuits. Measurement errors are reduced by a high input impedance.
