Filter Results By:
Products
Applications
Manufacturers
-
product
.13u ESD diode
Impulse TSMC
The Impulse TSMC .13u ESD diode was made to provide ESD discharge paths when integrating third party IP in an integrated circuit design for total ESD protection. The Impulse ESD diode has been successfully used with Dolphin Technologies, Artisan/ARM, TriCN/Synopsis I/O libraries, as well as popular IP blocks from RAMBUS, Chip Idea and other quality IP vendors. A 5.5 volt reverse bias anode to cathode operational specification enables the Impulse TSMC .13u ESD diode to be the device of choice for 5 volt tolerant designs.
-
product
Dual Surge Current Generator
MIG0624T-K12
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
product
Multiple Impulse Generator
MIG0624LP1
MIG0624LP1 is a multiple impulse generator with four independent outputs each of 6kA and 1 Ohm source impedance. These are combined to deliver impulses up to 24kA. The impulses generated by this equipment are the 8/20µs and 10/1000µs current impulses. Typical applications would be testing of varistors, gas arresters and other surge protection devices.
-
product
AC Insulation Testing
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
product
4-Channel, Sigma-Delta ADC Function Card
ProDAQ 3430
The ProDAQ 3430 is a 4-channel, sigma-delta ADC function card. Every channel contains front-end conditioning circuitry followed by a sigma-delta ADC. The bit stream from every ADC is then directed to finite impulse response (FIR) decimation filters. Users can activate up to 10 stages of the FIR filters. The filtered data from the selected stages is then stored in the FIFO. The data from the FIFO easily can be moved on-the-fly to the motherboard or to the host.
-
product
Smaart SPL
Smaart SPL offers the same complete SPL measurement toolset from Smaart v8 in a purpose-built standalone package, with an interface designed for simplicity and speed. Smaart SPL provides a powerful and full-featured solution for monitoring, metering, and logging SPL but with a format and price point more accessible to users who don’t require the real-time frequency and impulse response mode analysis capabilities of our flagship Smaart v8 software.
-
product
Impulse Current Generator
Weshine Electric Manufacturing Co., Ltd
Impulse current generator is mainly used to test the ability of electrical equipment to withstand strong impulse current, widely used in lightning arresters and electrical and electronic equipment in operation conditions of oscillation wave immunity test, can also be used for other research tests.
-
product
Audio Test Tone Generator
ToneGenerator
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
product
Impulse Hammers
Impulse hammers are designed for frequency measurement of mechanical structures, such as mechanical mobility, mechanical damping and impedance.
-
product
Impulse Withstand Voltage Tester
SUG255
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
product
Control Devices
National Meter Industries Inc.
4-input impulse centralising equipment. Inputsare optoisolated to read impulses and it has a 32-bit memory to store the valuesmetered.
-
product
Impulse Test Equipment
mpulse test equipment for testing of low-voltage rotator windings.The equipment is composed of a surge impulse generator circuit, phase selector unit (selection between U, V and W), and waveform recorder circuit to provide a differential method type of impulse testing instrument.
-
product
Non-Programmable Signal Conditioning
7525
The Dynamics 7525 Differential Amplifier was designed for use in high-speed data systems. It is completely compatible with all tape recorders for direct recording and is also useful for isolating digital or high-speed impulse signals when you cannot afford to reconstruct the signal or change pulse characteristics.
-
product
Qualification and Quality Control Tests
Techsquare
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
product
Turn-Key Short Circuit Laboratories
For low and medium voltage switchgear including :*Circuit breakers*Contactors*Disconnect switches*Fuses*Miniature circuit breakersApplied tests for low and medium voltage switchgear :*Dielectric withstand test*Impulse withstand test*Breaking capacity test*Mechanical life testElectrical life test*Over load performance test*Short circuit breaking capacity test**Short time short circuit impulse current test*Temperature rise test*Operation performance testTests for low & medium voltage panels :*Short time short circuit impulse current test*Dielectric test*Impulse withstand voltage test*Temperature rise test
-
product
Primary Cable Fault Locating
Directional Impulse Detector
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
product
Magnetizing Power Supply
This is a magnetizing power supply which can be used even in areas (countries) with an unstable electricity supply.The accuracy of the repeating magnetizing voltage enhances our reputation for top-class quality in the industry.We confirm the peak value, the time of electrification, and the electrical current area by using an impulse meter (a highly accurate magnetizing ammeter) before we ship out the products.
-
product
Impulse Response Measurements
Dirac
Dirac is a sophisticated tool to calculate a very wide range of acoustical parameters from impulse response measurements of an enclosure. Through many years of development and customer feedback, Dirac has grown to support many different applications. Due to its user friendly interface it is suitable for field measurements, but it also contains many advanced features that make it useful in a laboratory or research setting.
-
product
Discharge Tester
It is a new impulse winding tester that incorporates high precision, a wide range of functions, various expandability, improved operability, and a full range of external communication interfaces.
-
product
Universal Scanning Head
CF106
Calmet Smart Calibration Devices
Universal miniature scanning head for detecting (counting) impulses from inductive, LED and LCD energy meters. Additionally it enables counting of manually triggered impulses (Start/Stop push button function). Sometimes (when access is difficult) it is the only way to count pulses from inductive, LED and LCD meters.
-
product
Solutions for Nondestructive Characterization of Elastic
Sonelastic
Sonelastic® is a line of solutions for nondestructive characterization of elastic modulus and damping of materials by the natural frequencies obtained by impulse excitation technique.
-
product
Current Tester
MIG0624
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
product
Munitions Testing
E-Labs has an extensive background in the development and testing of Less Than Lethal (LTL) devices. We were the first to develop a measuring system to capture blunt force or impulse of a round in real time. The Ballistic Impulse Measuring System (BIMS) developed by E-Labs was used on USMC programs to evaluate LTL rounds and compare impulses on a one to one basis.
-
product
Digital Impulse Voltage Measuring System
TR-AS
The well-established Impulse Voltage Measuring Systems TR-AS, including the digital recorders from our own development and manufacturing, where further developed consequently and now feature improved sampling rates up to 200 MS/s in real-time with 14 Bit resolution simultaneouly in up to 16 measuring channels.
-
product
Iris
Marshall Day Acoustics Pty Ltd
3D acoustic impulse response - measurement and visualisation. IRIS is a powerful and user friendly measurement system for capturing and analysing room impulse responses in 3D.
-
product
Power Transducer
Beijing GFUVE Electronics Co.,Ltd.
Devices capable of transforming or converting a certain type of input energy into another different from the output, they serve to obtain information from physical and chemical environments to obtain electrical signals or impulses and vice versa.
-
product
Resistance Tester
KT-2000RD
This equipment represents the wanted resistance value in digital figures and at the same time, is an ohmmeter which decides products to be bad in case of being out of the previously set range of H,L and to be good in case of being within the range. Moreover, because it is designed and manufactured on the basis of KAST's business experiences and know-hows accumulated through on-the-spot works for a long time, it is highly trustable, especially strong to noise and impulse that occur on the bad electric condition of on-the-spot or on the connection with any other equipments, and also is convenient for use.
-
product
Current Tester
MIG1248
The MIG1248 is a current generator with wave shape 8/20. Maximum impulse current is up to 48kA supported by a 12kV impulse voltage making the MIg1248 ideal for testing large varistors. An intergrated test cabinet can accomodate test components up to 5cm cube.
-
product
High Voltage Impulse Test Set Up
We are renowned as the foremost manufacturer and exporter of High Voltage Impulse Test Set Up. This testing equipment is demanded in electrical, power generation and engineering sector. It is incorporated with fiber optic isolated digitizers to test various types of transformers. We utilize excellent grade raw materials to engineer and develop this High Voltage Impulse Test Set Up in accordance with industry standards. Our clients can get this equipment from us at competitive price.
-
product
Metrology System
IMPULSE V
With tighter wafer-to-wafer and within-wafer uniformity tolerances, integrated metrology systems are in use across various semiconductor processing steps. Based on demonstrated high-resolution optical technology, the IMPULSE V system provides higher sensitivity to thin film residue measurements during the CMP process. The IMPULSE platform boasts the industry’s most reliable hardware with best-in-class reliability and productivity metrics.
