Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 1-Pole
40-321-103-HI
The 40-321-103-HI (PXI) and 42-321-103-HI (PXIe) are hex 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Differential Voltage Probes
DP150/DP200pro
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
product
ScopeCorder
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
product
ScopeCorder
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
product
Data recorder
Cobra
The Cobra High Speed Recorder is a unique solution for high speed data recording and playback at a rate of up to 20 GB/s (160 Gbps). The system utilizes the PXI Express architecture to provide a modular, flexible solution that can be customized to nearly any requirement. The main recording engine, Cobra, is a PXIe board with high speed RAM and a high performance Xilinx FPGA. This board manages the data movement to and from storage devices and also provides optical fiber channels for high speed data input or output. The Cobra board can be used alone or in concert with additional Cobra boards.
-
product
16 or 32 channel Digital to Analog Converter
LS-71-P
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
product
Data Acquisition Recorders & Loggers
B&K Precision offers a full range of data acquisition recorders & loggers for measuring parameters such as voltage, temperature, current, resistance, frequency, and pulse. From high speed recording with deep memory, to long battery life for portability.
-
product
High Temperature Clip-On Gages (700 C)
Model 7641
Jinan Testing Equipment IE Corporation
These COD gages use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7641 is ideal for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. All units can be displaced slightly in compression for ease of installation. The COD gage is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the COD gage. This system provides a number of functional enhancements, including: high speed digital output, built in calibration and tare functions, analog and digital filters, and more. The 7641 is readily interfaced with most existing test controllers, and may be directly connected to a data acquisition system or chart recorder, or directly to a PC. The 7641 may be used for strain controlled tests such as JIC.
-
product
Cable Diagnosis System
Baseline 9400 TDR/ICE
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
product
Airborne Network Flight Test Recorder
TTC nREC-7000
Curtiss-Wright Defense Solutions
The nREC-7000 is a high speed network recorder for use with Flight Test Data Acquisition and Multiplexing units. The nREC-7000 accepts data for recording on two 10GBASE-SR ports and two 1000BASE-T ports that can store data at sustained speeds of up to 1,000 MBps per 10GbE port. The recorder is also capable of acquiring, formatting (using PCAP, DARv3 or IRIG-106 Chapter 10/11), and recording 10GBASE-SR Ethernet at line rate.
-
product
SHC68-C68-RDIO2, 68-Pin VHDCI Male to 68-Pin VHDCI Male, 80 MHz, Shielded Digital Cable, 1m
156166-01
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 1m
-
product
HDD-8261, 4 TB, 6-Drive, PXI Data Storage Module
784191-01
4 TB, 6-Drive, PXI Data Storage Module - The HDD‑8261 in-chassis PXI Express high-speed data storage module features an onboard PCI Express SATA controller. The module fits into a PXI Express chassis, and it occupies only three PXI slots. With the HDD‑8261, you can choose between hard-disk drives (HDDs) or solid-state drives (SSDs) for increased ruggedness. It is ideal for field testing or signal recording applications. You can use this module to not only stream high-speed data, but also to easily move data between multiple test setups or supplement the PXI system controller’s storage capacity.
-
product
Standard 3.27 (93.00) - 8.13 (231.00) High Frequency Probe
K-50L-QG
Bandwidth @ -1dB (GHz): 4.00Return Loss @ -20dB (GHz): 0.80Nominal Impedance (Ohms): 50Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 225Recommended Travel (mm): 5.72Overall Length (mil): 1,830Overall Length (mm): 46.48
-
product
Standard 3.74 (106.00) - 14.35 (407.00) High Frequency Probe
K-50L-QG-75
Nominal Impedance (Ohms): 50Bandwidth @ -1dB (GHz): 12.00Return Loss @ -20dB (GHz): 3.00Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 1,575Overall Length (mm): 40.00
-
product
Standard 3.74 (106.00) - 14.35 (407.00) High Frequency Probe
K-50L-QG-75R
Nominal Impedance (Ohms): 50Bandwidth @ -1dB (GHz): 12.00Return Loss @ -20dB (GHz): 3.00Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 1,637Overall Length (mm): 41.58
-
product
Standard 0.79 (23.40) - 1.75 (49.60) High Frequency Probe
CSP-40G-021
Your product description goes here.
-
product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
product
Standard 3.74 (106.00) - 14.35 (407.00) High Frequency Probe
K-50B-QG-75R
Nominal Impedance (Ohms): 50Bandwidth @ -1dB (GHz): 12.00Return Loss @ -20dB (GHz): 3.00Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 1,637Overall Length (mm): 41.58
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Windows Driver & SDK for ADLINK PCI/PCI Express/cPCI Series Data Acquisition Cards
PCIS-DASK
ADLINK PCIS-DASK is an advanced 32-/64-bit kernel driver and 32-bit/64-bitDLL Library for custom data acquisition application development. PCIS-DASK provides a common set of Application Programming Interface (API) for ADLINK"s extensive family of PCI/PCI Express(R)/cPCI Series Data Acquisition Cards, and is ideal for custom applications development under 32-bit/64-bit Windows 7/8. With PCIS-DASK, you can easily access all functionality of ADLINK DAQ PCI/cPCI general series data acquisition cards.
-
product
8-CH Thermocouple Input Module
ND-6018
- Channels: 6 Differential & 2 Single-ended- Input Type: Thermocouple, mV, V and mA- Thermocouple Type: J, K, T, E, R, S, B, N,C- Voltage Range: ± 15 mV, ± 50 mV, ± 100 mV, ± 500 mV, ± 1 V, ± 2.5 V- Current Range: ± 20 mA- Isolation Voltage: 2500 VRMS
-
product
16-CH 16-Bit 250 kS/s Low-Cost Multi-Function DAQ PCI Express Cards
DAQe-2213/2214
ADLINK DAQe-2213/2214 can sample up to 16 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 8 AI channels in order to achieve maximum noise elimination.
-
product
16/32 -CH 16-Bit 250/500 KS/s Multi-Function DAQ Cards with Encoder Input
PCI-9222/9223
The ADLINK PCI-9222/PCI-9223 is a 16-bit, 16/32-CH, 250/500 KS/s high performance DAQ card with 8 different input ranges. It also features 2-CH 16-bit analog outputs capable of a 1 MS/s update rate, 2-CH encoder inputs, and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, high-speed DIO, general-purpose timer/counter, pulse generation, and PWM output. Analog input, analog output, and function I/O at full speed simultaneously, and multiple cards can be synchronized through the SSI (System Synchronization Interface) bus if users need more channels than a single board can provide. Ideal for mixed-signal tests, laboratory research, and factory automation, PCI-9222/PCI-9223 is the best single-board solution on the market providing the best integration capability of multiple tasks with high performance and an affordable price.
-
product
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
PCI-9111 Series
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
product
Data Acquisition DSP Based 16 Channel
CPCI-AD8-opt8
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
product
8DI/8DO Modbus RTU Remote I/O
ND-6150
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
USB to RS-422/RS-485 Converter
ND-6530
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
15-CH Isolated Digital Output Module
ND-6056
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Standard 4.47 (127.00) - 12.00 (340.00) High Frequency Probe
K-50B-S
Current Rating (Amps): 6Bandwidth @ -1dB (GHz): 4.00Return Loss @ -20dB (GHz): 2.50Nominal Impedance (Ohms): 50Test Center (mil): 600Test Center (mm): 15.24Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 90Recommended Travel (mm): 2.29Overall Length (mil): 1,205Overall Length (mm): 30.61
-
product
High Speed Data Acquisition Module
ADQ214
The ADQ 214 data acquisition card features dual channels, 14-bit resolution, 400 MSPS capture rate with 1.4 GHz analog input bandwidth, and a memory buff er of 64 MSample per channel. The combination of high speed, high resolution and wide bandwidth makes it ideal for broadband applications such as IF sampling of RF signals and high-speed data recording. PXI Express, USB interfaces.
-
product
Industrial Data Acquisition Module for embedded systems with PCIe/104 OneBank expansion
PX1-I440-ADC
The PX1-I440-ADC is an industrial data acquisition module for embedded systems with PCIe/104 OneBank expansion. This module features eight differential ADC (analog-to-digital converter) inputs based on the Analog Devices LTC2335-16 ADC. Analog to digital inputs terminate to a single 20-pin box header connector.
