Filter Results By:
Products
Applications
Manufacturers
HIL
a system's simulation test of embedded controls by the electrical emulation of it's motors, sensors and actuators.
See Also: Loop, Current Loops, Loop Testers, Hardware in the Loop Simulation, Hardware-in-the-Loop
- Pickering Interfaces Inc.
product
PXI Fault Insertion (Fault Injection) Modules
PXI Fault Insertion Units (FIU), also known as Fault Injection switch products, are designed specifically for safety-critical applications where the response of a control system is required to be evaluated when sensor connections behave in unexpected ways. These modules are scalable solutions that can be used to switch signals between simulations and real-life devices in a multitude of hardware-in-the-loop (HIL) simulation and test systems. The fault insertion unit can significantly simplify and accelerate the testing, diagnosis and integration work in HIL applications.
-
product
Stackable And Configurable Signal Generator For CAN Applications.
K- Volt
The K-Volt can be used to generate fast configurable analog and digital signals from CAN messages. Designed for high speed and accurate simulation of sensors (For example HIL and Replay systems). The K-Volt can be connected directly to a PC via a USB connection.
-
product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
PXI-2722,16-Bit, 5-Channel PXI Programmable Resistor Module
781985-22
16-Bit, 5-Channel PXI Programmable Resistor Module—The PXI‑2722 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2722 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
product
Custom Testing Solutions
Test and MeasurementEnable increases the robustness of your test and measurement solutions, thereby reducing errors and associated costs. Data Acquisition (DAQ)Enable defines and builds custom DAQ systems for automated measurements of any process or manufactured part. Control and AutomationEngineeringEnable ensures that your processes are programmed to be safe, effective and optimized for both speed and quality. Real-Time and Mission CriticalSystemsEnable develops dependable real-time systems and Hardware in the Loop (HIL) simulations for high-speed applications. Motion ControlEnable creates software for synchronized multi-axis robotic control of velocity, position, force and action. Machine VisionEnable implements software and hardware-based solutions for precise image analysis, data extraction and vision-guided machine control. R&D Systems/Product DevelopmentEnable’s team of engineers and scientists works with you to address and solve problems containing technical challenges and uncertainties. Electronic Test SystemsEnable programs and builds software and hardware-based solutions for accurate measurements, from DC to RF. Mobile App DevelopmentEnable enhances your systems by integrating custom iOS and Android apps. Web DevelopmentEnable enhances your systems by integrating desktop and mobile web frameworks using PHP, CSS and HTML5. Database DevelopmentEnable decentralizes your data storage to be online, secure and accessible from anywhere.
-
product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
Real-Time Target Machines
Speedgoat offers a range of high performance multi-core, multi CPU target computers (target machines) with i3 and i7 CPUs up to 4.2 GHz, and up to 20 cores. Each is optimized for a different application area, from mobile controller prototyping (RCP) to multi-target rack systems for Hardware-in-the-Loop (HIL).
-
product
Software Platforms
Discover complete solutions for Hardware-in-the-Loop (HIL) and Rapid Control Prototyping (RCP) testing. OPAL-RT offers the most advanced real-time simulation software platforms for power systems, power electronics, aerospace and automotive sectors: RT-LAB (Multi-domain, MATLAB/Simulink® based), HYPERSIM (Power Systems), and NI VeriStand (Automotive).
-
product
PCIe-7822, Kintex 7 325T FPGA, Digital Reconfigurable I/O Device
785360-01
The PCIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
FlexRay Interface Device
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
FADEC/EEC Test Platform
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
PXI Signal Insertion Switch Module
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
product
PXIe-7821, Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module
783485-01
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7821 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
Multifunction Reconfigurable I/O Device
Multifunction Reconfigurable I/O Devices feature a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop (HIL) testing, custom protocol communication, sensor simulation, and high-speed control.
-
product
HIL Breakout Board
Onboard 192 pin snap-in terminal dramatically simplifies the wiring between your control hardware and your HIL system. As soon as the system is up and running there are 192 test terminals for easy access to all the interface signals: firing pulses, control feedback signals and other analog/digital I/O signals.
-
product
Simulation Systems
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
product
PXI Multifunction Reconfigurable I/O Module
PXI Multifunction Reconfigurable I/O Modules feature a dedicated analog-to-digital converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. You can customize these models with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop (HIL) testing, custom protocol communication, sensor simulation, and high-speed control. PXI Express models also include peer-to-peer streaming for direct data transfer to other PXI Express models.
-
product
NI HIL and Real-Time Test Software Suite
Suites combine LabVIEW Professional Development System with NI's most popular application softwareIncludes LabVIEW Professional, VeriStand, and the LabVIEW Real-Time and LabVIEW FPGA modulesEach new suite includes a one-year NI Training and Certification membershipSoftware is shipped on USB 3.0 media with NI device drivers included to speed up your installationConfigure real-time test applications quickly and easily; add custom functionality
-
product
Routing Card
SET-2010
With 64 single-ended or 32 differential channels, the SET-2010 provides exceptional signal routing capabilities in a small form factor. Unlike traditional routing matrix cards, the SET-2010 is designed specifically for the challenges of signal routing in HIL systems.
-
product
Vehicle Multiprotocol Interface Device
The Vehicle Multiprotocol Interface Device excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
PXI Programmable Resistor Module
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
-
product
Panel-mounted HIL Power Amplifier
PAC60Ci
PAC60Ci is the six-phase real time simulation amplifier, with maximum RMS phase current of 30A and maximum output power of 450VA. This current amplifier is possessed of high accuracy and fast liner response.
-
product
PXI Vehicle Multiprotocol Interface Module
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
*C Series CAN Interface Module
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Bloomy Simulation Reference System
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
