Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Receiver, 9025TR, 25 Module, With 20" Platform, For Tabletop
310104436
The 9025TR receiver includes a platform with runners that provide a smooth-sliding action, ideal when using large fixtures. It can be adapted to accommodate vacuum or mechanical fixturing. VPC modules can be intermixed to establish flexible custom interfaces which are ideal for functional and system testing applications. The 9025TR uses all standard modules and contacts, and includes a microswitch. Includes rear cover to protect wiring.
-
product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
Test Engineering
TestEdge engineers have an average of 17 years of engineering experience in test, packaging, and fixturing. This experience is across a wide spectrum of products, customers, and ATE platforms. We have experience in all of the following:Digital, analog, mixed-signal, RF Test programming servicesRemote test capability Semi-automatic test generation Automatic data collection and reduction High performance test fixturing Format independant vector translation High power testing with liquid cooling
-
product
F9 Systems CalBlade
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
product
Combinational Base Test Platform
6TL24
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid-volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
product
Benchtop Test System
300 Series Benchtop ATE
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
HASS / HALT Chamber
Typhoon 4.0 PLUS
This system is designed specifically for the task of performing Highly Accelerated Stress Screening (HASS) and HALT on large products. With the Lowest Total Cost of Ownership within the AST industry, the 48" x 48" vibration table is capable of supporting hundreds of pounds of products and fixturing, and delivers more energy in the lower frequency ranges necessary to stimulate failures in these large products.
-
product
In-Line Functional Test Fixtures
Add an advantage to in-line production with fast change over interchangeable fixturing. Circuit Check’s in-line board handlers and in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading handlers.
-
product
Test Fixturing Solutions
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
-
product
Tripod
10753B
The Keysight 10753B Tripod provides a mounting for the Keysight 5519A/B laser head. The tripod allows Keysight 5530Laser Calibrationsystem optics to be located remotely from the laser head, yielding greater accuracy and simplifying fixturing. The remote setup also eliminates heat-caused distortions. The Keysight 10753B adjusts for height, rotation, tilt, and lateral offset. The tripod is collapsible, covers a height range of 900 mm (35.5 in) to 1630 mm (64.0 in), and has a net weight of 14 kg (31 lb). The Keysight 10753B tripod complements a family of measurement optics and lasers that comprise Keysight laser interferometer calibration systems.
-
product
Laser Calibration System, Superior Accuracy, Portability and Reliability
5530
The configurable system offers all the components you need to perform a variety of measurements using the USB on your PC as the host controller and power source. For basic linear measurements you will need the USB Axis Module, USB Sensor Hub, Air and Material Sensors, Sensor Cables, Software, Laser, Laser Cable, Remote Control (optional)and the Linear Optics Set. Other available options include the Laser Tripod (with laser mounting plate), optics and fixturing kits for making additional types of measurements, and wheeled transit cases.
-
product
In-Circuit Testing
If you are looking for in-circuit test applications, equipment or advice, our experienced engineers can help you. Whatever your fixturing requirements or special software features, our long history of work in this field means that we have probably seen and done it before.
-
product
Fixturing Kit
10744A
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
product
Life Cyclic Durability Testing
Environment Associates can provide everything you need for cyclic durability testing and performance fixturing. Services include mechanical cycling to a position or load, fatigue cycling to a fixed load, rotational torque cycling, and simple push/pull cycling. EA can design your fixture with electro-dynamic, air, or hydraulic assistance to mechanically move your part. All of our fixtures can be manufactured to withstand a wide range of temperature, humidity and vibration inputs. If required, forces can be monitored electronically, using a wide variety of inputs (i.e. strain gages, load cells, rotational transducers, thermocouples, shunts, and more). EA can create holding and check fixtures to perform “pre” and “post” evaluation for dimensional issues that may occur during testing. EA can provide fixtures for single tests run internally for EA test labs and can manufacture fixtures to be purchased directly by the customer for their internal use.
-
product
9075 - 75 Module Solution
VPC rack mountable receivers like the 9075 meet the standards essential to support advanced mass interconnect requirements. The 9075 receiver is designed to accept the 9025, 9050, 9050 VXI, and 9075 ITA and can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed to create custom interfaces which are ideal for functional and system testing applications.
-
product
DC Current Bias Supply
DC1000A
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
product
In-Line / Board Handler
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
product
Flying Probe Systems
Smaller production series and fast prototyping requirements combined with zero fixturing costs are factors driving the development of Flying Probe testers. Today, Flying Probe Technology has matured and Columbia can supply single- or double-sided flying probe testers to be used on both loaded and bare PCBs.
-
product
Standalone with Drop-In Test Systems
800 Series ATE
The Circuit Check 800 Series ATE provides the versatility of utilizing the economical drop-in fixturing present in the 600 Series or an integrated dedicated fixture, while simultaneously providing the increased test equipment capacity of the 1000 Series. This combination produces a cost effective full turnkey test solution.
-
product
Femto / Picoammeter, 0.01fA, Battery
B2983B
The B2983B Femto/Picoammeter is the world’s only graphical picoammeter that allows you to confidently measure small currents with 0.01 fA (0.01 x 10-15 A) resolution. In addition, battery operation eliminates AC line noise from your critical measurements. It possesses a 4.3” color LCD with a graphical user interface that provides trend chart and histogram data in addition to numeric information. These front-panel capabilities enable you to capture transient behavior and to perform quick statistical analyses without a PC. The available Setup Integrity Checker software option allows you to compare the noise levels of different cabling and fixturing arrangements to help isolate external noise sources.
-
product
Fixturing
Terotest specialises in providing test solutions specific to customers' test applications. We understand that the interfacing and fixturing of a particular test setup can determine whether the application is a success or a failure, and therefore we strive to deliver solutions that are cost effective and suitable to user requirements.
-
product
Lab-Type Environmental Stress Screening Chambers
ESS5/11 SERIES
The ESS5/11 Series provides the unique capability of stress screening products in a small, lab-type chamber. Pre-qualification for ESS, troubleshooting, and small scale ESS programs would all benefit from high air flow, high change rate testing in this compact design. This series can accommodate up to six product drawers from our standard ESS systems. Other features include non-CFC/HCFC design, and wide variety of control systems, refrigeration system sizes, and product fixturing options.
-
product
Fixture Building Software
FixGenius
Tests show that FixGenius’ rule-based probe-mapping algorithms reduce pin deflection by up to 25% compared with traditional fixturing packages. FixGenius comes with a powerful Fixture Editor that allows the user to change the probe mapping. If a solution is mathematically possible, FixGenius’ algorithms will find it, and pick the one with least deflection. If the job simply cannot be done with one single fixture, FixGenius will fully automatically split the test into multiple fixtures or into fixture and flying probe test sets, with guaranteed test integrity.
-
product
9050TR - 50 Module, 2-Tier Solution with Platform
The rack mountable 9050TR receiver is designed to accept 9025 and 9050 ITAs and is essential to support advanced mass interconnect requirements. This 50-module solution can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can also be intermixed to establish custom interfaces which are ideal for functional and system testing applications.
-
product
Flying Probe Testers
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
product
High Voltage Tester
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988EL
The i3070 Series 5i Inline ICT retains the popular and proprietary Keysight short-wire fixturing technology used in our stalwart Keysight 3070 and i3070 systems.
-
product
XCITE 1100-5 Inertial Mass Excitation System
The 1100-5 Inertial Mass Modal Excitation system allows the testing of structures where backup fixturing is not available or possible. Accelerating an internal mass with the closed loop hydraulic excitation system generates the inertial forces. The compression control of the Xcite Master Controller maintains a constant force over a frequency sweep by continuously altering the drive signal to maintain the required dynamic force level.
-
product
Receiver, 9025TR, 25 Module, with 20" Platform
310104435
Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR can be adapted to accommodate vacuum or mechanical fixturing. VPC modules can be intermixed to establish flexible custom interfaces which are ideal for functional and system testing applications. The 9025TR uses all standard VPC 90 series modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit. Slide kit required, but not included.
-
product
Bare Board Electrical Testing
ProbeMaster
ProbeMaster is the complete software solution to your shops needs in bare board electrical testing. ProbeMaster is PentaLogixs top-of-the-line software package that combines all of the power of the PentaLogix CAM and Fixturing packages with support for moving probe, Netlist Comparison and other robust features.
