Filter Results By:
Products
Applications
Manufacturers
Fiber
cylindrical dielectric waveguide, which transmits light through total internal refraction. AKA: Fibre
See Also: Fiber Optic, Fibre
- Virginia Panel Corporation
product
Mini Fiber Optic, Contact, Receiver, Polymer Optic Fiber
610113170
This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113171. (May mate with other ITA contacts, as well.)
-
product
100G Multimode Fiber Testing and Latency
Fiber Lab MPO
With data centers and other high-speed networks using multimode optical fibers for short distance 100G applications, Fiber Lab MPO is the first solution to provide an efficient approach for
-
product
Field Fiber Cleaver
HW-09C
Shanghai Fibretool Technology Co.,Ltd.
The Fibretool HW-09C is a single fiber cleaver designed to accommodate either 900µm buffered or 250µm coated fiber. The HW-09C cleaver's quick and easy three-step operation is well suited for mechanical splice and quick termination field connector applications. The leaf spring base is ruled to allow for cleave lengths of 2 to 20mm. The standard carbide blade will perform up to 6000 cleaves before replacement.
-
product
Optical Fiber Analysis System
2200
The 2200 Optical Fiber Analysis System provide high-speed characterization of the spectral loss of single-mode and multimode fibers. Configurations include the 2200 for single-mode fibers, the 2210 for both single-mode and multimode fibers, and the 2220 designed for single-mode fiber ribbons. All three systems employ unique fiber preparation and signal processing techniques, which deliver both the measurement performance and the testing throughput required by high volume fiber, cable and component manufacturers. Options are available for mode field diameter and multimode numerical aperture measurements.
-
product
Matrix Fiber Optical Switch at Single Mode Type A 1550nm with LC/PC Connector
GLSUN-MEMS-8x8
Guilin GLsun Science and Tech Group Co., LTD
Fiber Configurations 8x8 ports Fiber Type SM, 9/125 umTest Wavelength 1530/1570 nm Operating Voltage 4.8~5.5VSwitch Type Non-latching Fiber Length 0.5m±5cmConnector LC/PC Tube Type 900 umOperating Temperature -10°C~ +70°C Storge Temperature -40°C ~ +85°C
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-018-M50
The 40/42-852A-018-M50 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Compact Fiber Seeders
LightWire FFS Series
LightWire FFS series fiber lasers are dedicated for seeding solid state femtosecond Yb:YAG based CPA systems. Ekspla offers FFS lasers either with femtosecond pulse duration directly from fiber, or with chirped pulses.
-
product
Temperature sensors
TC-03
The Temperature Chain TC-03 is a spliceless chain of several fibre optic temperature sensors in series. The sensors are all contained in a 1mm stainless steel tube which is directly connectorised on one end.
-
product
Instrument Systems General Accessories
Konica Minolta Sensing Americas, Inc
Instrument Systems General Accessories current range of optical probes and measurement adapters using fiber optics as a means to transport light in the spectrometer was a primary goal sought by Instrument Systems from the beginning of their product development.
-
product
Optical Fiber Sensing
Nanning Xionghua Photonics Technology
Optical Fiber Sensing by Xionghua Photonics
-
product
FT-NIR for Process Analytics
QuasIR™ 2000E
Galaxy Scientific’s QuasIR™ 2000E is designed for continuous measurement of the chemical composition of material transported on a conveyor belt, through a pipe, or in a chute. Our unique external projection optics use high powered tungsten lamps to illuminate the sample from as far as 24 inches away and collect the scattered reflection off the sample through a fiber optic cable. The analysis spot size can be set as small as 0.5″ or as large as 8″ in diameter and can be custom tailored to applications needs.
-
product
Fiber TAPs
Profitap fiber TAPs provide secure in-line network access for the monitoring of 1–400 Gbps fiber networks. By splitting the light flowing on the network link, fiber TAPs deliver an exact copy of the data for real-time monitoring and analysis, without disrupting the network. Passive fiber optic TAPs require no power, and therefore introduce no point of failure when deployed in a network.
-
product
High-Tc Systems
We offer easy to handle high-Tc systems with liquid Nitrogene as coolant. You can choose between fibre reinforced plastic vessels or glass dewars with robust Teflon shell.
-
product
Splice Closures
A connection part that connects two or more fiber optical cables together and has protective components.
-
product
- Single Mode to Multimode Converter
Model 279
FEATURES: DC to 2.5 MBPS; Full duplex; 850nm to 1300nm; In line mounting; Small size; Data LED's; Line Loss switch; Single-mode distance to 20 Kilometers. The Model 279 provides transparent conversion between fiber optic devices utilizing multi-mode fiber and those with single-mode fiber.
-
product
Off-Card Adapter,
3910-FOFE
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, FC/APC Connectors
42-852A-018-M62.5
The 40/42-852A-018-M62.5 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
LXI Optical Switching - 8x8 Matrix Plugin Module
65-280-313
The 65-280-313 8x8 matrix is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
High and Low Temperature Humidity Chamber
GDJS/GDJW
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
product
(125×150×22mm) Single-Channel Full Function Standard Booster EDFA module
EATV5100-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
The EATV5100-FM05 standard Booster EDFA module provides high power, high reliability, and superior optical performance in an industry standard form factor. This product enables deployment fo flexible, high-density optical networks, while reducing capital and operating applications' requirements. This module is ideal for today's highly dynamic networks and cost sensitive market. EATV5100-FM05 Full Function Booster EDFA Module adopts Standard Versions for Single Channel and Narrowband. The EDFA includes a cooling pump laser, input monitor and input isolator, output monitor and output isolator, and a reel of optimized erbium-doped fiber. These components are contained within a standard 125×150×22mm package.
-
product
LXI 8:1 Optical MUX FC/APC Loop-Thru
60-850-021
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Fiber Testers
Shenzhen Noyafa Electronic CO.,LTD
Provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
product
Real-Time Ethernet Master/Slave Network
EtherCAT
EtherCAT is an open real-time Ethernet Master/Slave network developed by Beckhoff. Today, it is an open standard, managed by the EtherCAT technology group. EtherCAT sets new limits for real-time performance since it processes 1000 distributed I/O in 30 µs or 100 axis in 100 µs using twisted pair or fiber optic cable. Regarding topology, EtherCAT supports a simple low cost line structure, a tree structure, daisy chaining or drop lines - no expensive infrastructure components are required. Alternatively the classic more expensive switched star topology can be used.
-
product
Structured Cabling
Diverse line of fiber optic cables for structured cabling and enterprise applications.
-
product
Polarization Maintaining Collimator
Zhongke Rayzer Optical Technology Co.,Ltd
The basic element for in-line PM fiber optics components, such as PM Isolator, PM FWDM, PM Filter Coupler and PM Circulator. It has high extinction ratio, low insertion and high return loss. The unique processing and high quality AR coating also enable this collimator tohandle high power.
-
product
Fibre Channel Simulator & Analyzer Applications Software
fcXplorer Simulyzer
Avionics Interface Technologies
FC-1, FC-2, and FC4 Analyzer modes and displays - Frame parser for custom display of FC frames and payload data - Captured data can be saved as binary or “csv” files - User-defined trigger and filter features - “Live Capture” real-time display - Error detection and reproduction - Complete control of the transmit link - Replay of recorded data with precision timing or corrected protocol timing - Special testing functions such as defining command/response for exchange management
-
product
Satellite Optical Receiver
SSR-15CW
Hangzhou Softel Optic Co., Ltd.
*Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using high linear PD*Output connected to 5 IN series satellite multiswitch*Build-in optical AGC function*Red-LED for power indication*Smaller size and easier installation
-
-
product
Core Alignment Splicer
Model：95S
OFS-95S fiber optic fusion splicer is designed as a highly flexible instrument with 6-motor precise micron levelcontrol and splice loss lower than 0.02dB for G.652 fiber. Equipped with removable universal fiber holders (250μm/900μm/patchcord/FTTx indoor fiber etc.), SOC holder and internal thermometer / barometer, OFS-95S can be deployed anywhere. Fast 5s startup, 9s splicing and automatic heating features enable the splicer an efficient tool for large volume splicing operation during fiber installation and maintenance.
-
product
DVI Extender via Two Singlemode/Multimode Fiber Optic Cable up to 4,920 Feet
ST-2FODVI-LC
The XTENDEX® DVI Extender via Fiber Optic Cable locates a single link digital DVI display away from a computer up to 4,920 feet using singlemode fiber optic cable and 1,640 feet using multimode fiber optic cable. Supports resolutions to 1920x1200.
