Filter Results By:
Products
Applications
Manufacturers
ESD
ESD Testing Equipment includes Surface Resistance/Resistivity Meter, Electrostatic Field Meter, Wrist Strap Checker, and Constant Wrist Strap Monitors.
See Also: ESD Test, Surface Resistivity
- TEAM SOLUTIONS, INC.
product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
product
.13u ESD diode
Impulse TSMC
The Impulse TSMC .13u ESD diode was made to provide ESD discharge paths when integrating third party IP in an integrated circuit design for total ESD protection. The Impulse ESD diode has been successfully used with Dolphin Technologies, Artisan/ARM, TriCN/Synopsis I/O libraries, as well as popular IP blocks from RAMBUS, Chip Idea and other quality IP vendors. A 5.5 volt reverse bias anode to cathode operational specification enables the Impulse TSMC .13u ESD diode to be the device of choice for 5 volt tolerant designs.
-
product
ESD Simulators
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
product
Shoes and Wrist Strap Tester
WST100
• Tester designed for checking the conformity of operators wrist strap and/or shoes to the ESD protection standard.• It is also designed to be permanent wall mounted in a production facility for daily testing of employee’s wrist straps and footwear.• Easy to operate, red and green LEDs give clear “pass” or “fail” indication• Individual tests for the wrist strap, the right and left shoe• Can register up to 60 000 different measurements• Output for interface with PC or automatic door opening system• Operates battery that can be supplemented with an AC net adaptor• Tester and calibration plug are delivered with a certificate ofcalibration
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
product
Resistance Meter - Portable, Precision Resistance Measurement from 0.10 to 1.00 x 10^12 Ohms
PRS-812B
- Wide Range Resistance: 0.10 Ω to 1.00x1012 Ω- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Constant Test voltages 10V and 100V for specification measurements to meet international and domestic ESD measurement standards- Auto Resistance Range Control- Auto Test Voltage Control- Uses a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- 120 Data Set Internal Memory- Uses Standard USB Cable for Charging- Charges in 2 Hours- 2-year Limited Warranty on Main Instrument
-
product
BF-Series Soft Stop Models
The E-DRIV® BF-Series soft stop models is designed with an unique "soft-stop" shock absorbing clutch that is ideal for fastening shock delicate components such as disk drives, plastics, and electronics. The ergonomically designed soft stop clutch reduces impact and vibration transmitted in the screw fastening process, which delivers less torque reaction to operator. The electric screwdriver offers an adjustable speed setting and a selectable Soft Start mode. Designed for precision torque control the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
product
Transient Suppression for Corelis JTAG Controllers
TAP Protection Adapter
Transient events such as Electrostatic Discharge (ESD), inductive switching, and lightning can damage electrical equipment, leading to costly repairs and test equipment down-time, reducing production capacity and increasing time-to-market.The Corelis TAP Protection Adapter is designed to enhance protection to any Corelis JTAG controller, shielding against harmful events using a combination of electrical defenses.The compact adapter features series resistors and transient voltage suppressor (TVS) diodes to mitigate damage to the JTAG controller. Protect your investment and enjoy peace-of-mind with the TAP Protection Adapter.
-
product
Stand-Alone Automated ESD Scanner
SmartScan 550
API's main hardware platform that most scan technologies can be integrated to this platform. 550 represents the four-axis robot arm size. It is a stand-alone model.:
-
product
Steering Diodes
ProTek's low capacitance Steering Diode Arrays provide high-speed data line and I/O port protection from transients caused by Electrostatic Discharge (ESD), Electrical Fast Transients (EFT), Tertiary Lightning and other induced voltages. Steering diodes divert the transient to the power-bus or ground and away from sensitive IC components.
-
product
ESD Event Detector
Novx MiniPulse
Simco-Ion's Novx MiniPulse ESD Event Detector is designed for tool and process monitoring. This affordable, small footprint embeddable monitor has been developed to warn of product damage risks at the point of electrostatic discharge. The MiniPulse uses time domain and threshold discrimination to detect pulse electromagnetic energy. Through the use of specific antenna configurations and placement, the MiniPulse can provide ESD event detection for well-defined small areas.
-
product
Assembly & Test Services
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
product
ESD Ground Point
EGP-020
The EGP-020 ESD Ground Point is a convenient mechanical socket that can be mounted on to any equipment frame for equal-potential bonding to the equipment. The 4 mm socket is not insulated, made of lathed brass, nickel-plated, for use as grounding socket.The EGP-020 is designed to be mounted on an unpainted conductive surface.
-
product
GEM GroundHog Monitor
The G.E.M. GroundHog, a Multi-Ground Continuous Monitoring Automation System, is the newest addition to the robust ELITE family of electronics from Botron Company Inc. With a rich feature set never before available, ESD facilities and sensitive component manufacturers can monitor critical grounds in real time in applications ranging from the benchtop to capital equipment.
-
product
Touchplate Combo Wrist Strap And Footwear Tester
Testing ESD Wrist Straps and ESD Footwear prior to entry on the fab floor, or ESD Protected Area is a simple, yet very effective means towards becoming ESD compliant and establishing proper ESD controls. This is a no-frills, “go-no-go” type tester. Meaning, you get either a green or red indicator upon passing or failing, respectfully. It is battery operated and the trimpot calibration make the lifetime overhead of this tester a cost effective choice.
-
product
ESD Latch Up Tester
1100-ESD
Tokyo Electronics Trading Co., Ltd.
The Model 1100-ESD can easily and accurately perform ESD tests (HBM, MM) on ICs up to 64 pins. Also, all common pin combinations required by the standard can be realized.
-
product
Voltage Touch Monitor
The AlphaLab Voltage Touch Monitor enables personnel to identify voltage problems that usually remain hidden. The monitor reads the voltage on a finger (which is identical to the voltage at every other point on the body). It can detect as little as 1/10 volt in two modes: DC and AC/Spikes (ESD transients). In the DC mode, the displayed voltage is either positive or negative, and is usually very low if grounding is being worn and is functioning properly. Higher DC voltages (even while grounded) occur if a DC ionizer is blowing too close or if the person rubs against a high-static material or comes in contact with metal at a DC potential. If personal grounding is not being used, any DC signal can build up over time, and the DC mode continues to show the instantaneous body voltage as it changes. In the AC/Spikes mode, any transient voltage spike at least 1/2 millisecond long is temporarily displayed. If there are several consecutive spikes, only the highest is displayed, regardless of polarity. If the signal is a repetitive (AC) wave, the peak voltage is displayed, but always as a positive number. Even when proper grounding is worn, several tens of volts often occur with transients and AC. Maximum error for DC and AC is only 2% of the reading +/- 0.1 volt.
-
product
Test System
4003 TLP+™
The Model 4002 TLP+™ test system was the first turn-key commercial TLP developed for the ESD industry and has remained the leader in the ESD square pulse testing field since this method was first introduced in 1989. This tester is the ultimate design and analysis tool for ESD protection circuits. It provides Pulse Curve Traces of circuit characteristics which simulate ESD tests. This allows you to see into a chip’s operation taking out the guesswork which speeds your design and minimizes lost time.
-
product
Power Limiter, 0.01 to 50 GHz
N9355F
The N9355F power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
product
Tabletop Ionizing Transport System
90610-03610
The Model IT-7000 Ion Transport System is a self contained, compact table top ionizer capable of producing copious amounts of both positive and negative ions. The variable speed fan permits a gentle flow of ionized air, reaching a distance of up to 4 feet. A charged object, when passed through the ionization field, becomes neutral instantaneously. Inherently balanced, the Ion Transport System has a fail safe balance indicator to assure proper ionization output for ESD static control applications.
-
product
Wrist Strap Tester
Statclean Technology (S) Pte Ltd
ESD wrist strap is most commonly used protective devices which prevent the build-up of electrostatic charge on personnel. The random failure of wrist strap compromises the protection. Thus, it is important to test every wrist strap regularly.
-
product
Series HAND-HELD Electrostatic Voltmeter
Model 520
The Trek Model 520 Hand-Held Electrostatic Voltmeter (ESVM) Series products provide accurate, noncontacting measurements of electrostatic surface voltage for ESD applications in either ionized or non-ionized environments. Industrial applications include measuring charge accumulation in the LCD manufacturing process or measuring static charge in semiconductor production.
-
product
Digital/Analog Audit Kit
Botron's Digital/Analog Audit Kit insulation and continuity tester is designed for electrical testing. The wide range of test voltages makes the Audit Kit ideal for users involved with ESD testing. The kit gives greater functionality with simplified operation and an ergonomically designed case.
-
product
Stat Guardian Plus Constant Monitor
ests person, wriststrap, and matLED and buzzerNIST calibration includedWorks with single wire capacitance wriststrapsCE markCan be calibrated110v AC suppliedProduct conforms to the ESD S.20.20 spec standardsGround dock included
-
product
Visual Fault Locator
HW-205
Shanghai Fibretool Technology Co.,Ltd.
The HW-205 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.- 2.5mm universal connector- Operates either in CW or Pulsed- Constant output power- Long battery life (up to 60 hours)- Laser case ground design prevents ESD damage- Portable and rugged, easy to use- Burning testing to ensure the reliability.- Optional 1.25mm connector adapter
-
product
Transmission Line Pulse Testing
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
product
ESD Safe Fume Absorber
ESD safe, carbon-activated fume absorber. Flux creates "pine resin", which creates noxious fumes. These fumes cause headaches and nausea. This unit quickly removes these fumes from the work area and filters them safely. Only this newly developed unit, mounted on its versatile 37" arms, allows easy movement to effectively remove these irritating fumes fast.
-
product
ESD - Simulator
SESD 216
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
