Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Digital I/O Board, 16 Optically Isolated I/O Channels, 24V
APCI-1516
PCI interface to the 32-bit data bus? 8 isolated input channels, 24 V? 8 isolated output channels, 10 to 36 V,output current 500 mA? Timer-programmable watchdog for the reset of the outputs to ??? One ground line for all inputs and one ground line for all outputs? Outputs set to "0" at PowerOn/Reset
-
product
Digital Attenuators
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
product
Digital Phase Shifter
Analog Devices digital phase shifters change the phase of RF, microwave, or millimeter wave signals while providing no amplitude change. They are used in a variety of applications, including RF PA linearization/RF distortion, amplitude and phase modulation, variable attenuators, and fiber optics.
-
product
LXI Modular Chassis
Our LXI modular chassis are available in 7-slot or 18-slot and support over 1,000 of our PXI modules, additionally our 2-Slot USB/LXI Chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. These range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of T&M modules such as programmable resistors, digital I/O, power supplies, battery simulators and attenuators.
-
product
Attenuator Modules
The Analog Devices portfolio of wideband digital attenuators and voltage variable attenuators (VVAs) modules helps meet designers’ diverse needs. Low cost, high accuracy control, and small package options provide solutions for RF and IF applications, including the space, communications, and military industries.
-
product
Digital Step Attenuators
Ranatec’s digital step attenuators covers all mobile frequency bands and gives a calibrated attenuation range of more than 90 dB in steps of 0.25 dB. All Ranatec digital attenuators are built as modules and offers both serial and parallel control logic.
-
product
Digital Attenuators
Compact microwave digital step attenuators with low insertion-loss, USB control and power, 60 or 90dB max setting, 0.25 or 0.5dB step size, ranging from 10MHz to 24GHz. Front OLED display and user control buttons standard.
-
product
Attenuators
CAES offers a full range of RF Attenuators for your designs including analog and digital PIN Diode as well as Switched-bit Attenuators.
-
product
Digital Step Attenuators (DSA)
High linearity, fast switching time with broad bandwidth. Best-in-class attenuation error with fine attenuation steps. Most robust ESD protection available.
-
product
Digital Attenuator Operating Frequency of 1 to 20 GHz
LDA Series
The LDA series of Lab Brick® RF and Microwave Programmable Digital Attenuators includes 50 Ohm and 75 Ohm bidirectional RF step attenuators with calibrated operation up to 20 GHz. These USB powered and controlled units require no additional DC supply voltage. They are easily programmable for fixed attenuation or swept attenuation ramps directly from the included GUI. Lab Brick Digital Attenuator API DLL, Linux drivers and LabVIEW-compatible drivers are also available for custom programming applications.
-
product
Programmable Digital Attenuator
LDA-602EH
The LDA-602EH has a large attenuation range of 120 dB with an exceptional 0.1 dB step size, allowing for both precision and accuracy during fading tests or device characterizations. This attenuator also features a fast 15 us switching speed, an operating temperature from -30oC to 50oC, a maximum RF input of +28 dBm, and is priced at $875. The LDA602-EH operates with a low insertion loss of 9 dB to 6 GHz, an input IP3 of +55 dBm and a typical VSWR of 1.3:1. Easily programmed for ATE applications, the LDA digital attenuators are a cost effective solution whether you are in engineering, the production test lab, or in the field. Units are ROHS compliant and can be used with any PC or laptop computer with USB 2.0 port (or powered USB hub) and Windows operating system. Lab Brick Signal Generators are provided with easy to use Lab Brick GUI software, 32 and 64 bit API DLL files, LabVIEW and Linux compatible drivers.
-
product
USRP-2901, Software Defined Radio Device Bundle
784114-01
USRP-2901 Software Defined Radio Device Bundle - The USRP-2901 Teaching Bundle includes two USRP (Universal Software Radio Peripheral) Software Defined Radio Devices, turnkey courseware, and other accessories such as USB 3.0 cables and SMA attenuators. Students can use USRP … Software Defined Radio Devices with LabVIEW to experiment with real-world signals in introductory communications and digital communications laboratories. The USRP-2901 Teaching Bundle helps students experiment with FM radio, GPS, GSM, Bluetooth, and ISM signals. The bundle also includes components of a lab station that students can use to gain hands-on experience with live communication links between multiple USRP Software Defined Radio Devices.
-
-
product
Programmable HiRes Wideband Digital Attenuator
LDA-133
The LDA-133 Digital Attenuator is a bidirectional, 50 Ohm step attenuator. It provides fast attenuation changes from 10 to 13000 MHz with a step size of 0.5 dB and 63 dB of control range. All attenuators are easily programmable for fixed attenuation, swept attenuation ramps and fading profiles directly from the included Graphical User Interface (GUI). Alternatively, for users wishing to develop their own interface, Vaunix supplies LabVIEW drivers, Windows API DLL files, Linux drivers, Python examples and much more.
-
product
LXI And LXI/USB Modular Chassis
Our LXI modular chassis are available in 7 and 18-slot and our LXI/USB modular chassis are available in 2, 4 and 6-slot and support over 1,000 of our PXI modules. The PXI modules supported range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of simulation modules such as programmable resistors, digital I/O, power supplies, thermocouple simulators, function generator, battery simulators and attenuators. This gives you enormous flexibility to define a switching or T&M system to exactly match your needs.
-
product
Digital Attenuator
Chengdu KeyLink Microwave Technology Co., Ltd.
The products can be used in microwave electronic components. Its attenuation values are determined by the input TTL/LVTTL control signal. So that the link can be achieved the desired gain or loss value.KeyLink's digital attenuators can be categorized as follows.
-
product
Digital Control Step Attenuator
Digital control attenuators with TTL parallel control offering fast switching speed and high attenuation accuracy
-
product
USRP-2900, Software Defined Radio Device Bundle
784113-01
USRP-2900 Software Defined Radio Device Bundle - The USRP-2900 Teaching Bundle includes two USRP (Universal Software Radio Peripheral) Software Defined Radio Devices, turnkey courseware, and other accessories such as USB 3.0 cables and SMA attenuators. Students can use USRP … Software Defined Radio Devices with LabVIEW to experiment with real-world signals in introductory communications and digital communications laboratories. The USRP-2900 Teaching Bundle helps students experiment with FM radio, GPS, GSM, Bluetooth, and ISM signals. The bundle also includes components of a lab station that students can use to gain hands-on experience with live communication links between multiple USRP Software Defined Radio Devices.
-
product
USB/Ethernet Control Step Attenuator
Digital control attenuators with Ethernet or USB control
-
product
RF Attenuators
Over 400 coaxial, surface mount, and MMIC attenuator models for 50-Ohm & 75- Ohm syetem including fixed attenuators, high-power attenuators, digital step / programmable attenuators, voltage variable attenuators and more. DC passing and DC blocking models. Power handling up to 100W. Bandwidths spanning DC to 50 GHz.
-
product
Digital Step Attenuators
Analog Devices provides a range of broadband IC digital attenuators that come in low cost, leadless surface mount packages. Our digital attenuator family offers excellent attenuation and includes off chip ac ground capacitors for near dc operation, making it ideal for an extensive number of RF and IF applications.
-
product
PXIe-6569, PXI FlexRIO Digital I/O Module
787284-01
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
product
Dynamic Digital I/O (3U), 16 Ch., Per Pin Control, Up To 200 MHz W/256MB Memory & LVDS
GX5293
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 16 ch., per Pin Control, up to 200 MHz w/256MB Memory & LVDS
-
product
Industrial I/O Module
DIO-3460
The DIO-3460 is a space-saving industrial I/O module. It provides for save cable connections due to the use of WAGO Cage Clamp connectors rather than screw terminals.
-
product
FPGA PXI Digital I/O Card
GX3500
The GX3500 is a user configurable 3U FPGA PXI card which offers 160 digital I/O signals for specific application needs, as well as providing pin for pin compatibility with NI PXI 7811R and 7813R FPGA cards. The card employs the Altera Cyclone III FPGA which can support clock rates up to 150 MHz and features over 55,000 logic elements and 2.34 Mb of memory.
-
product
PCIe LVDS Digital Waveform Acquisition - 250 MBit/s Internal Sampling Rate Timing, 250 MBit/s External State Clock
M4I.7725-X8
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
product
Industry Pack Carriers and Digital I/O
CPCI-4SIP-6U
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
product
64-CH Isolated Digital I/O Modules
cPCI-7432/7433/7434
- Two external interrupt sources for cPCI-7432/7432RP/7433- 3U Eurocard form factor, CompactPCI compliant (PICMG 2.0 R2.1)- 32-CH isolated digital inputs & 32-CH isolated digital outputs for cPCI-7432- 64-CH isolated digital inputs for cPCI-7433- 64-CH isolated digital outputs for cPCI-7434/7434P- 5000 VRMS isolation voltage
-
product
PCI-6513, 64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated Digital I/O Device
778970-01
The PCI-6513 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6513 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
SHC68-C68-D4 Shielded Single-Ended Cable, 0.55 m
781013-01
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, 0.55m, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
