Filter Results By:
Products
Applications
Manufacturers
- CAMI Research Inc.
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
product
Automated Measurement System
EVG®40NT
The EVG40 NT (stand-alone tool) and the AVM (HVM-integrated module) enable measurement of lithography relevant parameters like critical dimension, as well as bond alignment accuracy.Because of the high-measurement accuracy, it is possible to verify compliance to tight process specifications and instantly optimize integrated process parameters.
-
product
PXIe Measurement Accelerator
M9451A
The M9451A PXIe Measurement Accelerator combined with Option DPD Digital Pre-Distortion & Envelope Tracking Gateware shows what is possible when you combine state of the art FPGA's with Keysight's trusted measurement expertise and PXIe's high speed data handling. As part of Keysight's RF PA/FEM Characterization & Test, Reference Solution, this combination provides unprecedented performance for demanding envelope tracking and digital pre-distortion measurements required for testing modern power amplifiers (PAs) and front-end modules (FEMs). Hardware acceleration provides better than 20x speed improvement over Keysight's previous host-based Reference Solution, with closed/open loop digital pre-distortion (DPD) and envelope tracking (ET) measurements taking just tens of milliseconds and overall measurement times less than 70 ms.
-
product
PXI FPGA & Measurement Accelerator
Keysight PXI FPGA & measurement accelerator provide digital-pre-distortion (DPD) and envelope tracking (ET) measurements that are embedded in high performance FPGA processing cards.
-
product
Dimension & Displacement Measurement
Ono Sokki Dimension & Displacement Measurement - digital linear gauge, rotary encoder, non-contact thickness meter, laser doppler surface velocity meter.
-
product
Critical Communications
The mission of Public Safety Communications is to meet the mission-critical communications requirements of First Responders. Morcom recognizes the extensive range of capabilities that this entails.
-
product
Deep Observability For Critical Edge Software
DevAlert
Get cloud-based observability on anomalies in edge devices and embedded software. Detect and analyse issues remotely, during testing and in deployed devices. Use your familiar desktop tools for secure remote debugging.
-
product
Safety Critical Miniature Relays
CU-U Series
The CU-U is a so called safety relay which is used in places where a safe separation between coil and contact circuit is required. The relay is, with the corresponding screw socket V12, according to CEE 15/2e edition, approved by KEMA, for application in gas fired installations.
-
product
Measurement
DC Voltmeter
DC Voltmeter is used for measuring DC voltage coming to the input channels of ADC modules and FFT spectrum analyzers. The indicator displays the DC voltage mean value and root-mean-square deviation (RMSD) from the mean value of the selected channel signal. It is possible to change the averaging of the displayed value (0.1; 1, or 10 s) and to select a necessary channel of the ADC module and FFT spectrum analyzer or a virtual channel.
-
product
IR Temperature Sensors for Critical Equipment Monitoring
FLIR A310
The FLIR A310 is a fixed-mounted thermal imaging camera that can be installed almost anywhere to monitor your critical equipment and other valuable assets. The camera can safeguard your plant and measure temperature differences to assess the criticality of a given situation. This allows you to see problems before they become costly failures, preventing downtime and enhancing worker safety.
-
product
In-depth Execution Time Analysis For Critical Software
RapiTime
*Timing analysis (inc. WCET) for Ada, C & C++ on-target & host**Identify code to optimize for worst-case behavior*Debug rare timing events*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
product
Measurement
Strain Gauge Meter
The program Strain gauge meter is intended for various strain gauge measurements with the use of strain gauge transducers (e.g., force and torque transducers, RPM sensors, bridge and half-bridge circuits based on strain gauges, etc.) and a measurement module for strain gauges ZET 017-T.
-
product
Zero-footprint Coverage Analysis For Critical Software
RapiCoverZero
*Collect coverage from systems that produce branch traces*Save time with efficient merge and mark verification workflow*Simplify verification through integration with your CI tool*Collect coverage for libraries without source code
-
product
Measurement
Phasemeter
Phasemeter is used for measuring the phase difference of two signals coming to the input channels of FFT spectrum analyzers. The upper line of the indicator displays the current phase difference value in degrees, the lower line – phase difference value in radians. It is possible to change the averaging of the displayed value (0.1 or 1 s) and to select necessary FFT spectrum analyzer channels.
-
product
Measurement And Control
Amplicon supplies Measurement and Control products for every type of application, from high-end Test & Measurement to a simple digital panel meter installation. We have products that can monitor, display and log high and low speed signals.
-
product
UFL Measurement
Many of the well known VNA manufacturors offer very expensive calibration kits and special phase-stable cables (which costs almost as much a MegiQ VNA) for measuring impedances. This is useful for some special scientific measurements, or when working in the higher GHz, but a setup with an uncooperative cable and a bulky (N) connector is not suited for measuring the small devices that we are developing.
-
product
Measurement Software
Measurement Software – Comfortable software solutions from MCD allow the user an efficient acquisition and evaluation of specific test data. Especially in the audio and video analysis areas they are most often the cheaper solution to expensive hardware.
-
product
LCR Measurement
LCR component bridge with built-in test fixture and limits comparator with binning. Micro-ohmmeter with four terminal Kelvin clip leads. High basic accuracy, rechargeable battery operation.
-
product
Measurement System
CmForce
CeTaQ has developed a measuring system for the determination of placement force under real process conditions. This makes it possible to identify weaknesses at an early stage and to avoid component damage during the assembly process. With only one measurement; force and energy input of each nozzle are now known.
-
product
Power Measurement
Precision Acoustics manufactures Radiation Force Balances and Check Sources which can be used to measure ultrasound power according to the IEC Standard 61161. All products are supplied with a calibration from The National Physical Laboratory, LONDON.
-
product
Image Dimension Measurement System
IM-7000 Series
An instant solution to conventional quality inspection problems. Perform high-precision measurements, automatically record data, and generate reports with the push of a button.
-
product
Pressure Measurement
The Comark range of Pressure Meters is suitable for gauge or differential pressure and positive or negative (vacuum) pressure measurement. These instruments are ideal for applications like H & V, process pressures, laboratories and clean rooms, through to service and maintenance and the calibration of other instruments.
-
-
product
Measurement
Site VSWR
The Site VSWR measurement is done according to CISPR 16-1-4 in the frequency range from 1 GHz to 18 GHz using broadband omni directional antennas in horizontal and vertical polarisation. The volumetric test method is applied (test volume needs to be specified), test distance 3 m - any other distance upon request. The ground plane has to be covered with absorbing material.
-
-
product
Mission Critical, Fault Tolerant Power Supplies
Series HSF
- Hot-swappable plug-in power supplies.- Designed to be combined in an N+1 fault-tolerant power system.- Front panel voltage adjustment trimmer for adjustment of output voltage.- Built-in forced current sharing and or-ing diodes.- May also be used independently as a multi-output power supply.- Designed to be sustainable - new models are backward compatible with existing racks.- Available in 1U and 3U sizes. Mounts in 19-, 23-, and 24-inch equipment racks.- All models include power factor correction (PFC).- Full service customized DC power distribution systems can match power supply output(s) with your load(s).- I/O connections via 24 pin connector that plugs into rack adapter. External connections are made via rack adapter.- Surface mount technology permits minimum mounting space.- Entire RA 19 racks populated with HSF power supplies can be connected in parallel, parallel-redundant or series.- HSF are CE Marked per per the LVD, EMC and RoHS 2 Directives. See applicable Declaration of Conformity.- Compliant with UL 8750, Standard for LED Equipment,- Watch video of NEBS GR-63-CORE earthquake and office vibration testing.
-
product
Pressure Measurement
HighReach Measuring & Controlling System Co.,Ltd
The measurement of an applied force by a fluid (liquid or gas) on a surface.
-
product
Resistance Measurement
PROMET 100 / 200 / 600 high-accuracy, precision ohm meters deliver an adjustable test current up to 600 A which is independent of the supply voltage. They utilize the four-wire resistance measurement method, enabling them to meet extremely stringent accuracy requirements when determining resistance values in the micro-ohm range.State-of-the-art power electronics coupled with a robust design guarantee maximum reliability, even when used as portable devices in switching stations or industrial environments.The modern operating concept, an interface to the test systems of the ACTAS product line and an optional remote control unit make these micro-ohm meters flexible and versatile.
-
product
Stability Measurement
Biodiesel Rancimat
In the Biodiesel Rancimat, increased temperature and a continuous stream of air through the sample accelerate its aging. The time that passes until oxidation takes place at a high rate – the induction time or oxidation stability index (OSI) – is measured.
-
product
Functional Testing For Critical Software
RapiTest
*Requirements-based testing for Ada, C & C++ on-host & target*Reduce test authoring effort through easy-to-use test formats*Manage project artifacts with requirements traceability*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
product
Test & Measurement
Blonder Tongue Laboratories, Inc.
Tools to assist in video delivery installations, Blonder Tongue’s collection of Test & Measurement handheld products are second to none in capturing data for troubleshooting and testing purposes. These units provide real-time spectrum analysis, making them invaluable to those in the field.
