Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Matrix Switch Cards
1260-145 Series
These quickly and easily plug into the front of Astronics 1260-100 and 1260-101 Adapt-a-Switch™ carriers or Astronics 1256 GPIB/Ethernet and 1256L (LXI Core 2011 Compliant) switching mainframes.
-
product
52/20 Channel SPDT Plug-In Switch Card
1260-117/A
The Astronics 1260-117/A is a 52/20-channel, SPDT (Form C) plug-in switch card for the Adapt-a-Switch™ platform.
-
product
GPIB Controller Card
GPIB-PMC-XL
The GPIB-PMC-XL is a PCI Mezzanine Card GPIB controller card that converts any CPU card with PMC slots into a GPIB controller.
-
product
Probe Card Test & Analysis
Automated probe card test and repair is used to monitor probe card health to ensure cards are ready and capable of testing semiconductor devices. In cases where the card is not meeting performance specification, repairs may be performed such as tip adjustment or card cleaning, thus returning the card quickly to a production state.
-
product
96-CH High-Driving DIO Card
PCI-7396
The PCI-7396 is 96-bit parallel digital input/output (DIO) cards designed for industrial applications. The PCI-7396 emulates four 8255 Programmable Peripheral Interface (PPI) chips. Each PPI offers three 8-bit DIO ports which can be accessed simultaneously. The total 12/6 ports can be configured as input or output independently.
-
product
Carrier Cards and Bus Adapters
Abaco's wide range of carrier cards allows you to expand your systems capabilities simply and cost-effectively, allowing easier technology insertion.
-
product
Multifunction Analog I/O Card
LPCI-AIO16A
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
product
Fanless Embedded System With LGA1151 Socket 7th/6th Gen Intel® Core™ & Celeron® Processor, Intel® H110, HDMI, DisplayPort, VGA, 6 USB, 4 COM, PCI Express Mini Card Slot And 10 To 30 VDC
eBOX640-500-FL
The eBOX640-500-FL is powered by the 7th generation Intel® Core™ i7/i5/i3 and Celeron® processor families. It features dual DDR4-2133 DIMM sockets with up to 32GB of system memory, and provides a wide choice of front-accessible I/O interfaces for easy cabling and maintenance. It supports an extended operating temperature ranging from -10°C to +55°C, a wide voltage range DC power input from 10 to 30 VDC with power protection, and up to 2G vibration endurance, enabling a reliable and stable operation in harsh environment. The superior Intel® Kaby Lake-based fanless embedded box PC can support three independent high resolution displays and 4K resolution, offering high quality imaging.
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 2k
50-265-302
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 925Ω
50-297-121
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Express Mini Card Adapter for PCIe Slots
PCIe-mPCIe
The PCIe-mPCIe Adapter is a practical solution for system developers when the target embedded system platform is not yet available, but our PCI Express mini card I/O board is, and you need to get started developing and testing the hardware and software.
-
product
PXIe Card
pi922
Sundance Multiprocessor Technology Ltd.
The pi922 is a COTS integration combining the flexibility of a Kintex-7 FPGA PXIe card (PXIe/700) and a 5-channels ADC with 500MS/s converters at 16-bit resolutions (ADC500)
-
product
Video & Vision Cards
Advantech’s video and vision cards offer multi-channel image/video compression, transmission, and streaming capabilities for diverse interfaces.
-
product
Gigabit USB Device Server
DS-510
The Silex DS-510 is designed to easily connect and share USB devices over a network. Printers, Scanners, Disk Drives, Card Readers, or virtually any other USB device can be now be enabled with network capability. It allows flexibility to place the USB device anywhere on the network instead of needing to be attached directly to the computer, and multiple users can access the USB device.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm - SPST
50-294-114
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
JTAG/Background Debug Mode Test System PXI Card
NX5300
The NX5300 is a single slot 3U PXI device and interfaces to the unit under test via an On-Chip Debug (OCD) or JTAG port. The NX5300 is a high performance JTAG based background debug mode (BDM) diagnostic system designed for functional test, development, programming and troubleshooting of microprocessor and microcontroller based embedded processor systems.
-
product
Digital Stimulus Response PXI Card
GX5152
The GX5152 Series are high speed, 6U PXI, digital I/O instruments. The GX5152 master controller has 32 I/O channels that supports test rates up to 50 MHz and vector depths up to 128 Mb per pin. The GX5153 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5152. The GX5152 can control up to 15 GX5153 boards using the same timing and sequencer.
-
product
VME Sequencer PCI Express to VME Interface
SIS3104-2
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
product
PCI Programmable Resistors
Part of our Sensor Simulation family, these PCI programmable resistor cards are ideal for medical, aerospace and automotive applications.
-
product
Multiprotocol Serial Card
PCIe-ICM-4SM
The PCIe-ICM Series are a new family of isolated PCI Express serial communication cards. These PCI Express cards feature a selection of 4 or 2-ports of isolated, software selectable, RS-232, RS-422, and RS-485 serial protocols.
-
product
XMC Display Control Card
XM61000
LinkedHope Intelligent Technologies Co.,Ltd.
XM61000 is an XMC display control card independently developed by Linghao Intelligence®. It is mainly targeted at high-performance embedded graphics image processing and GPU general computing processing (GPGPU) applications.
-
product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
product
1553 Avionics Interface 3U CPCI Card
QCP-1553 Series
The QCP-1553 module is a rugged, reliable, full featured, Compact PCI module designed to provide a stand-alone, MIL-STD-1553A/B interface for avionics applications. Up to four independent dual redundant MIL-STD-1553 databus streams are supported by the 3U QCP-1553 module. Additionally, the module offers full functional test, simulation, monitoring and databus analyzer functions for MILSTD-1553A/B applications. An onboard IRIG-B time code decoder and generator allows users to accurately synchronize single or multiple QCP-1553 modules to a common time source. The QCP-1553 module is available in dual or full function (RT simulation, monitoring, and bus controller) configurations.
-
product
Off-Card Adapter,
3910-FOFE
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
product
Time to Digital Converter-1ns 5ch
FMC TDC
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) with a Time to Digital Converter chip to perform one-shot sub-nanosecond time interval measurements.
-
product
Interface
RXMC1553
Abaco Systems’ RXMC-1553 is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a XMC.0 Mezzanine Card. With one or two dual-redundant channels, the RXMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
-
product
Handheld Audio Analyzer
PAA3X
The PAA3X is a highly accurate handheld audio analyzer that gives sound engineers a rich array of sound analysis tools. The system features both 61-band and 31-band real time spectrum analysis, RT60 reverb time measurement, SPL and line meter, internal signal generator, EQ setting program, microphone calibration and speaker phase checking abilities. All functions and menus can be accessed through a central jog dial, leaving your other hand free to adjust audio settings. The large color LCD screen has an adjustable brightness to help you see in a dark or well-lit environments alike. The PAA3X also features a "screen capture" function allowing users to save images of the screen to an SD card in BMP format for later reference. The detachable precision microphone can be placed remotely via the included 5-meter extension cable, offering flexible on-site operation management. With all this plus a built-in rechargeable lithium-ion battery, the PAA3X is a must-have multifunctional tool for all serious audio engineers.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 1.02k Ohm
40-294-021
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
