Filter Results By:
Products
Applications
Manufacturers
- LBA Group, Inc
product
MW AM Broadcast Mobile Antenna System
TUP-3
The TUP-3 system is capable of transmitting efficiently at carrier frequencies from below 1000 kHz to over 1700 kHz. It is rated for power to 5000 watts, 125 percent modulated. Housed is a weatherproof cabinet, the integral tuning unit features high quality electronic components and matches the TUP-3 system to a 50 ohm transmission line. The self-supporting design of the tower also minimizes erection time and complexity.
-
product
Analog DVR
Sylo Vision Technology Co., Limited
Security cameras capture an analog video signal and transfer that signal over coax cable to the Digital Video Recorder (DVR). Each camera may be powered by plugging in the power supply right at the camera or by using RG59 Siamese cable which bundles the video and the power cables. The DVR converts the analog signal to digital, compresses it, and then stores it on a hard drive for later retrieval. Intelligence is built into the DVR to handle such things as scheduling, motion detection, and digital zoom. Monitors for viewing the video are connected to the DVR, or it can be set up to publish over an internal network for viewing on PCs. The DVR can also be set up to broadcast over the Internet and can add password protection and other features. When broadcasting over the Internet, the video for all of the cameras is transmitted as one stream (one IP address). Therefore, it is very efficient.
-
product
Advanced Test Platform
980 12G
The Teledyne LeCroy quantumdata 980 12G-SDI Video Generator / Analyzer module supports video and audio functional testing of next gen broadcast monitors, conversion devices and sources up to 12G-SDI. The module is equipped with four (4)12G-SDI-capable output ports. The output ports can be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. A genlock input supporting both SD analog black burst and HD tri-level to sync the output clocks with a "house sync" but the module can also run off its internal clock. The module's four (4) SDI input ports can also be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. For single link operation only port 1 on the input or output is functional.
-
product
Test Card Generator
TCG1
This generator provides a standard 75O, 1-volt p-p; PAL encoded CCIR video signal for the testing of monitors and other CCTV equipment. The Test Card Generator TGC1 may display one of four test patterns , (i) Colour bars with reference, (ii) Red Raster, (iii) Peak White Raster and (iv) Composite Test Card (see picture below). The Test Card Pattern incorporates many of the attributes of broadcast test patterns for the evaluation and setting up of CCTV video equipment.
-
product
Monitors
MW Series
The MW Series contains cutting edge, two-way, stage monitor systems designed for any high-energy live performance stage.
-
product
Real-Time Broadcast Analysis
Mediaproxy provides a comprehensive suite of software-based analysis applications to help you attend to on-air issues quickly and resolve them efficiently. Employing the latest user interface technologies, complex analysis tasks are made easy and seamless, including your mobile devices.
-
product
Power Monitors
NAI''s Power Monitors are used to monitor voltage, frequency, phase characteristics, or phase rotation of single- and three-phase power lines. Specifically designed for rugged defense and industrial applications, these Power Monitors meet the most stringent performance and environmental requirements.
-
product
Contamination Monitors
Control of X-ray and gamma radiation personal dose equivalent.The dosimeter together with the PC reader and the software forms an efficient automatic system for staff radiation exposure control.
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Workstation Monitors
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Workstation Monitors including critical process electrostatic moinitoring, event monitor embeddable ERDS monitoring, and multi-channel field voltage detection
-
product
Environmental Monitors
The tools and techniques designed to observe an environment, characterize its quality, and establish environmental parameters, for the purpose of accurately quantifying the impact an activity has on an environment.
-
product
SMS Broadcast
SMS Broadcasting System is designed to send information, SMS messages, cautionary messages to handsets on local areas.
-
product
Vibration Monitors
VS1 / VS2
Features • VS1 protects against excessive vibration levels • VS2 is ideal for use deliberately vibrating machinery • Settable RMS vibration velocity alarm trip-point and delay time • LED’s provide an instant view of machine status • Isolated SPDT relay output or transistor output • 24 VDC (18-30 VDC) powered
-
product
Under/Overvoltage Monitors
Contacts to control an external horn or light, or to signal your PLC are now available on independent accessories for any power supply. These modules can be used on power supplies with DC voltages from 5 to 125 Vdc. SPDT relay contacts switch if the power supply’s output deviates by:*1.0 volt or more (for 5 volt outputs)*2.0 volts or more (for 6 to 48 volt outputs)*3.0 volts or more (for 49 to 125 volt outputs)
-
product
Surface Quality Monitors
PET manufactures and markets non-destructive, non-contact surface contamination and thin film detection models and automated systems (surface quality monitoring system) capable of detecting thin layer contamination, thin films and coating down to the Angstrom level. These systems represent a major breakthrough by providing, for the first time, a quantitative measure of surface cleanliness. As surface cleanliness verification instruments, in a part cleaning environment, these products are capable of validating the cleaning quality of all the part cleaning equipment available in the market. Any of SQM model series is capable of verifying metal contamination; monitoring absence/presence of organic and/or inorganic on virtually on surfaces of all metals. They are, price/performance, the most sufficient product available for testing surface of metals for surface cleanliness. These systems operate in an ambient environment, require no sample preparation or deposit of any agents on the surface. In any parts cleaning environment where the quality and efficiency of part cleaning equipment for removal of surface contamination is highly desired, these systems provide a scientific solution by quantitatively measuring the surface cleanliness. The SQM series has the sensitivity and operational simplicity required to provide fast and cost effective surface evaluation for all metals.
-
product
Digital Broadcast Plug-In Elements
92000
The 92000 series of Coaxial Dynamics Digital Broadcast Elements are calibrated to exacting specifications to assure interchangeability with one another and may be used in any of our Digital Broadcast Wattmeters with appropriate size line section
-
product
Radiation Portal Monitors
SaphyGATE G is an easy-to-use Radiation Portal Monitor optimized for truck, train and cargo radiation control. It's based on large surface, high volume plastic detectors providing the highest sensitivity.
-
-
product
Broadcast Analyzers
Our product portfolio offers dedicated instruments for various terrestrial and cable TV and radio standards. For satellite applications, special options are available for our spectrum analyzers.
-
product
Cryogenic Temperature Monitors
Monitor temperatures from 1.4K to over 800K. Choose from one or eight standard inputs. USB, IEEE-488, and RS-232C interfaces, relays, and analog outputs are available.
-
product
Environmental Monitors & Loggers
Littlemore Scientific Engineering Co
Designed primarily for museums and art galleries these units measure the environment helping to ensure that sensitive objects are not damaged.
-
product
Vibration Monitors
Monitor vibration with these full-featured modules, available in portable and standard formats.
-
product
Remote/Local Broadcast Quality Assurance
AlertCenter
AlertCenter allows you to monitor one or more remote capture locations, recording multiple channels at each location. You can monitor and manage them from afar, using a single, centralized user interface, greatly cutting manpower and operational costs involved in having a monitoring operation on every site.
-
product
ATSC 3.0 Broadcast Stream Verification
StreamScope XM Verifier
The Windows®-based Verifier web app receives, tests, and records ATSC 3.0 broadcast streams from RF, Ethernet, and file inputs. With Verifier, you can monitor real-time graphs and charts of bitrates, signaling tables, RF parameters, packet errors, subframes, PLPs, and other KPIs.
-
product
Broadcast Video Products
Macom Technology Solutions Holdings Inc.
Macom Broadcast Video Products
-
product
Phase Monitors
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
product
Ground Fault Protection Monitors
The Earth Fault Resistance Monitor (EFREM) and the Rotor Health Monitor (RHM) provide wireless rotor ground fault and temperature monitoring for generators and motors. The systems replace older slip ring contact ground fault detectors on any synchronous generator or motor.
-
product
Industrial Panel PCs and Monitors
Advantech provides HMI and monitors with C1D2 certification. Apply to asset monitor and data process in harsh environments like O&G or pharmaceutical.
-
product
Environmental Air Monitors
TSI’s environmental monitors measure size fractions of particles and ultrafine particles. They capture PM1, PM2.5, Respirable PM4, PM10, and Total PM.
-
product
AC Voltage Monitors
NAI's AC- and DC-powered AC voltage monitors are used to monitor and measure voltage characteristics of single- and three-phase power lines. Field-adjustable AC voltage monitors are also available. These monitors are specifically designed for rugged defense and industrial applications.
-
product
Interrogation Monitors
Ibsen Photonics’ I-MON Interrogation Monitors set new standards for fast, real-time spectrum monitoring of FBG sensor systems.
