Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
50 Ohm SMB to BNC Cable Adaptor Assemblies - 3GHz
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
75 Ohm BNC to BNC Cable Assembly
40-977-701-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
HD BNC Male to BNC Female Cable, 50 Ohm, 20 cm
787230-0R2
The HDBNCM-BNCF connects measurement and signal devices. You can also use this cable to connect to other male BNC cables.
-
product
75 Ohm BNC to BNC Cable Assembly
40-977-701-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
product
MCX To BNC-M Trig/Sync Cable (DG/TB/TD/TL To DSO); 50cm; RoHS
CBMCXBNCMNAA
CBMCXBNCMNAA: trigger/sync cable. Spec.: MCX plug-BNC-M50cm length. For interconnecting DataGenerator, TravelBus, TravelData, or TravelLogic series trigger out to any DSO BNC input For trigger/sync input from TL4x34
-
product
BNC (F) To Alligator Test Clips
3788
Minigrabber? test clip hooks attach to terminal sizes up to .060? diameter. Converts BNC (Male) cables to Minigrabber test clips for test versatility.
-
product
BNC To BNC Cable, 50 Ohm, 0.9 M
781887-01
Connects measurement and signal generation devices. Model options include industry-standard coaxial connector types including BNC, SMA, SMB, and MCX. Long cables can act as antennae picking up extra noise that can affect measurements, so ensure you select only the length required for your test system. Also look at the impedance of your test system and consider buying a cable with the same impedance. Matched impedance can maximize the power transfer or minimize signal reflection from the load of your system.
-
product
BNC-2121, 68-Pin Female SCSI to Female BNC and Screw Terminals, Function Generator and Encoder, Desktop Mount, Shielded Terminal Block
778289-01
68-Pin Female SCSI to Female BNC and Screw Terminals, Function Generator and Encoder, Desktop Mount, Shielded Terminal Block - The BNC-2121 features eight dedicated and six user-defined BNC connectors and spring terminals, which allow access to all I/O signals. You can also use this terminal block to provide pulse-train, trigger, and quadrature encoder signals. The BNC-2121 includes a desktop mount.
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
8" Cable
COND25-1553
Commercial Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends. Military Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and two 18" cables with BNC cable jacks for I/O triggers.
-
-
product
SMA Male to HD BNC Male Cable, 50 Ohm, 1m
784995-01
The SMA-HDBNC Coaxial Cable provides connectivity for PXI instruments, such as FlexRIO modules.
-
product
DC Blocks
Coaxial DC Blocks allow the transmission of RF signals while blocking DC signals, usually using a blocking capacitor. We feature SMA DC blocks, 2.92mm DC Blocks, 1.85mm DC Blocks, BNC DC Blocks, TNC DC Blocks, and Type N DC Blocks. DC blocks can block the inner conductor, outer conductor, or both; hence there are "inner" dc blocks, "outer" dc blocks, and "inner/outer" dc blocks. These Coaxial DC Blocks are frequently used in Satellite Systems where a control voltage is passed along with the RF signal, and the coaxial dc block protects equipment. The BNC DC block uses a precision bnc to get to 4ghz. The C0927 SMA DC Block uses dual parallel capacitors to achieve its broad bandwidth, its ideal for EO & NRZ systems.
-
product
Low Noise Test Cables For N1413 With B2980 Series, 1.5 M
N1427A
The N1427A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1427A to the B2985B/87B.
-
-
product
Special Purpose Probes
6100 Series
Similar to a standard 10X scope probe except with BNC connections on both ends. With BNC connections on both ends, it provides a more stable connection when connecting to other equipment. This eliminates the use of a standard probe with a BNC adapter on the probe end that could come loose or break off the probe tip. The lead can be compensated to your scope with the trimmer tool included.
-
product
Cable Tester, Coax Cable Mapper 8 ID Finder with Toner
TCT-128
A handheld testing device designed for CATV and security installers to test multi-run coaxial cable systems terminated with "F" or BNC connectors. Uses eight color coded ID finders to locate and identify cables.
-
product
8" Cable
CONW1553-1
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
product
LXI Microwave Multiplexer, 50Ω 36-Channel 1-Bank 18GHz SMA
60-891-001-001
The 60-891-001-001 36 channel Microwave Multiplexer is suitable for switching 50Ω signals up to 18GHz. Connection is by front panel SMA connectors. This multiplexer is also available in a 50Ω BNC version which can switch signals up to 4GHz (model 60-891-001-002). The multiplexer has an extremely high level of performance with low VSWR, very high isolation, low loss and high power handling. It is ideal for switching 50Ω systems for HF up to microwave frequencies. It occupies 2U of rack space, providing a compact switching solution.
-
product
Audio Cable Tester
CBT-500
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
product
Near Field Probe Set
RF100
The RF100 probe set consists of a passive E field probe and H field probe, BNC adaptor and carry case. The output is via a BNC socket. These are general purpose probes which are ideal for use in conjunction with an EMC measuring system. They are sensitive to sources in close proximity, but are insensitive to background signals. This makes them ideal for the identification of emission frequencies in noisy environments... thus making measurements easier and quicker. The proximity requirement also enables sources to be located and the exit route identified.
-
product
Differential Voltage Probes
DP150/DP200pro
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
product
LXI Single 24x8 50 Ohm HF Matrix BNC
60-760-005
The 60-760-005 is a single 24x8 High Frequency Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50Ω and uses BNC signal connectors. It is also available in a smaller enclosure with SMB Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
product
LXI Dual 24x8 50 Ohm HF Matrix SMB
60-760-002
The 60-760 is a Dual 24x8 HF Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50 Ohm and uses SMB signal connectors, or with a larger case size, BNC Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-760-002 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
product
Remote Cable Tester for RJ45 RJ11 USB and BNC
REMOTETEST
Troubleshoot your wiring problems, quickly and affordably with StarTech.com's REMOTETEST, a Specially designed network wire tester that saves valuable time and effort when testing RJ45, RJ11 and BNC cables.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
75 Ohm Mini SMB to BNC Adaptor Assembly
40-978-701-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
BNC-2090A, 16-Channel, 1-Pin Female BNC, 68-Pin Female SCSI, PXI Multifunction I/O Module Terminal Block
779556-01
16-Channel, 1-Pin Female BNC, 68-Pin Female SCSI, PXI Multifunction I/O Module Terminal Block - The BNC-2090A is a desktop or rack-mount analog breakout terminal block that you can connect to compatible PXI Multifunction I/O Modules. The terminal block features 16 analog input (AI) BNC connectors for eight differential or 16 single-ended channels. The BNC-2090A also features two analog output (AO) BNC connectors, two user-defined BNC connectors, one analog programmable function input (APFI) BNC connector, one PFI BNC connector, and two 68-pin I/O connectors for DAQ device connection. Additionally, the BNC-2090A features spring terminal block for digital I/O and PFI connections.
-
product
T3 Low & High Voltage Differential Probes
T3 Series
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
