Filter Results By:
Products
Applications
Manufacturers
BERT
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: Bit Error Rate Testers
-
product
Bit Error Rate Tester
100G NRZ BERT
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
product
HDMI/Display Port Checker with 4ch x 12Gb/s Tunable BERT & EyeChecker
RB1204-HDMI/DP
*Low cost continuous 4ch, 1G to 12Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
product
400, 200, 100 Gbit Error Rate Tester
PAM-4 BERT
The MI-PE5610-1 is a PAM-4 BERT with an integrated propriety, optical PAM-4 modulator. ROSA testing is tremebous simpliefied by the integration of the optical PAM-4 modulator in the BERT chassis. This ROSA testing solution saves time and avoids trouble shooting and accelerates your product development. The BERT provides an excellent optical PAM-4 reference output signal with adjustable OMA of the three PAM-4 eyes.The implemented 3-Eye BER technique measures the BER in real time of the 3 eyes simultanously.A wide range of selectable pattern for compliance test and signal analysis is supported.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Electrical and Optical & Bit-Error-Rate Testers (BERTs)
OptoBERT™
The OptoBERT family of BERTs offers the best value in the industry for bit-error-ratio testing of optical and electrical components, subsystems and systems. OptoBERT family of products covers data rates from 100 Mb/s to 28.05 Gb/s.
-
product
Handheld Network Tester
T-BERD/MTS-5882
The T-BERD/MTS-5882 is extremely versatile, enabling the cell site technician to address all key tests with one, lightweight, handheld tester; including: Fiber Inspection: Dirty fiber connections are the #1 cause of network downtime. Microwave back-haul: The majority of microwave backhaul links around the world are still microwave. Enhanced Cable Diagnostics: Environmental factors can damage the CAT X shielded twisted pair cable connecting the microwave antenna. Fronthaul: Avoid dangerous tower climbs with CPRI testing including BERT, PIM detection, MIMO diversity, RET, and VSWR. Backhaul: In addition to packet testing across error-prone microwave hops.
-
product
Single Channel Error Rate Tester
Basic Bert
Already as a single channel BERT the PARALLEX® system offers full functionality for testing high speed components. PRBS and user pattern generation and error detection for 2..13Gbit/s.
-
product
64 Gbaud High-performance BERT
M8040A
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
product
Multi-Functional Ethernet Test Solution
PacketExpert™
PacketExpert™ 10GX is a comprehensive Ethernet/IP test solution supporting industry standard functionalities including wirespeed bit error rate testing (BERT), RFC 2544 / Y.1564 / RFC 6349 tests, packet capture, event-driven triggers and actions, traffic playback, impairment generation, stacked VLAN/MPLS tests, and many others.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
NRZ Bit Error Rate Tester
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
product
Photoreceiver
A lightwave digital receiver module designed for OC-192, DWDM, and Bit Error Rate Testing (BERT) of a digital optical link. The LRD-10-M is an O/E converter with post/limiting amplifier module designed for use in receivers up to 12.5 Gb/s data optical transmission systems.
-
product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
product
Software for Bit Error Ratio Testers
Customize your bit error ratio tester (BERT) with additional functions and features from an easy-to-use GUI to ensure you get the most out of your test instrument.
-
product
Hand Portable Test Instruments
GL’s PacketExpert™ 10G provides comprehensive testing of 10 Gbps wirespeed Ethernet/IP networks. It has two 10 Gbps Optical ports, and two 10/100/1000 Mbps Electrical/Optical ports capable of BERT, Smart Loopback, RFC 2544, ExpertSAM, Record and Playback, IPLinkSim™ and PacketBroker functionalities.
-
product
4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) With Eye Checker
RB3004
*Low cost continuous 4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
QAM And PCM Analyzers
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
product
Multi-Channel Synchronization Module for M8190A, M8020A or M8030A
M8192A
Complex testing sometimes requires playing multiple waveforms in parallel (e.g. multi-emitter testing). The M8192A synchronization module allows engineers to synchronize up to 12 M8190A channels and fits into a standard AXIe frame.The M8192A synchronization module also supports testing of high-speed digital busses like PCI Express.Test efficiency can be increased by testing up to 10 lanes with the M8051A and the M8041A BERT modules in parallel. These can be synchronized by the M8192A module.
-
product
Compact PCI Multi-function Decommutator
LS-50-cP
The Lumistar LS-50-cP 3U Compact PCI Multi-function PCM Decommutator offers the greatest flexibility in the industry by incorporating up to 10 functions typically encountered in flight test applications in a single 3U Compact-PCI card slot. Five functions are achieved on the main board (PCM Simulator which can also operate as a BERT, PCM Decommutator, IRIG Time CodeReader, IRIG Time Code Generator, and the same 5 functions can be achieved on the LS-55-DB Multi-Function Decom Daughterboard. CVSD Voice Decoding and h.261 Video Decoding are achieved through software.
-
product
Economical Solution for Test Requiring Fewer Instrumentation Modules.
OPTOWARE-S200 (FOTS-Bench Top Series)
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
ATE
Below is a list of high speed scopes and BERTs that form an integrated extension to Advantest’s V93000 ATE tester. In addition to these instruments, Multilane offers turnkey solutions for ATE testing.
-
-
product
E1/Datacom Transmission Analyzer
DTA-BERT
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
product
Bit Error Ratio Testers
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
product
Advanced Measurement Package For M8000 Series Of BERT Test Solutions
M8070ADVB
The M8070B system software for the M8000 Series of BER Test Solutions can be enhanced by additional software packages, such as M8070ADVB or M8070EDAB to get the best out of the M8040A, M8020A and M8030A J-BERT platforms.The M8070ADVB Advanced Measurement package offers advanced features like automated jitter tolerance test and parameter sweeps, eye diagram measurement or the integration of external equipment such as electrical and optical clock recovery or error analysis using a real-time scope.
-
product
Single Channel SFP+ All-In-One Sensitivity Tester
SFP+ Tester
All in one mainframe to perform a complete sensitivity test on a single channel fiber optic transceiver. Includes Clock source, BERT and all optical modules
-
product
E1 T1 Tester
NetProbe 2000 PDH
New Generation Analyzer for Legacy PDH networksThe NetProbe 2000 E1E3 is newest, state-of-the-art handheld analyzer on the market for testing the legacy E1 and E3 in PDH networks. It includes all features for E1 & E3 BERT and E1 physical layer testing. Automated line monitoring performs autocheck of essential alarms and errors.
-
product
Receiver Conformance Test Application for IEEE 802.3ck
M8091CKCA
Designed to assist and simplify the stress signal calibration used for testing the inputs of IEEE 802.3ck Draft 3.3 chip-to-chip (C2C) and chip-to-module (C2M) electrical interfaces using Keysight M8040A 64Gbaud Higher Performance BERT or an M8050A 120Gbd High-Performance BERT together with Keysight Digital Communication Analyzer (DCA) Oscilloscope or Infiniium UXR real-time Oscilloscope.
