Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
HandyScope HS5: 500 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 40MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-540XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 500 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
Fuel Display Unit Tester
MS 1125
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
product
Standards Waveform Generator
3110A
The 3110A software is built around the simple concept of a waveform segment. Each waveform segment can have a unique waveform, (sine, square, triangle, and/or DC offset). Frequency, amplitude and DC offset can be clipped, fixed, variable or swept. Segments can be calibrated (as required in CS101) and set to continue on to the next segment or to hold for an external trigger.
-
product
Scalar Network Analyzer Extenders
A Scalar Network Analyzer is a type of RF network analyzer that is used to measure only the amplitude properties of a DUT (Device Under Test). Unlike a Vector network Analyzer, it does not measure both amplitude and phase of the DUT.
-
product
Sensors
To measure machinery or structural vibration, a transducer is needed to convert the mechanical motion into an equivalent electrical signal. Each sensor has distinct advantages in certain situations and limitations in other, so it is important to select the most suited transducer or sensor for your job. Equally, important is selecting the appropriate parameter of vibration amplitude for measurement. IRD® has a wide range of transducers and accelerometers available to help you obtain accurate, reliable data, whether your concern is vibration monitoring, analysis, or dynamic balancing.
-
product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
product
PXI-5651, 3.3 GHz RF Signal Generator
779670-01
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Detector
In the measurement setup of SQUID electronics (detector variant), the dc SQUID amplifies the small amplitude signals of the detector with a large bandwidth so that they can be further processed with conventional AD converters.
-
product
Phase Modulated Driver
The Phase Modulation Capable RF Driver / Stabilizer is an eight channel, two phase RF driver intended to drive devices such as the Harris H-401. The driver provides both amplitude and phase modulation capabilities in a single unit. The device can be operated in driver mode where the operator has full control over amplitude, frequency, and phase, or in stabilizer mode where the driver automatically adjusts the operating parameters based on optical feedback from an optical pick-off point.
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/S/C , Programmable Amplitude Balance
LS-16A-R1-24SLSC
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
Quantum & Metrology Instruments
Beyond quantum sensors, Exail’s photonics solutions enable real applications in other quantum technology fields. They also enable precise control and transmission of the frequency, phase and amplitude of a laser light through fibered telecommunication links, for metrology applications. The true and deep understanding of Exail teams for the fundamental physics behind its technology explains the absolute quality of its time & frequency reference products.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-01
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
Arbitrary Waveform Generator
HDAWG
The Zurich Instruments HDAWG multi-channel Arbitrary Waveform Generator (AWG) has the highest channel density available in its class and is designed for advanced signal generation up to 750 MHz bandwidth. The HDAWG comes with either 4 or 8 DC-coupled, single-ended analog output channels with 16 bit vertical resolution. The outputs can be individually switched between a direct mode, with maximized bandwidth and superior noise performance, and an amplified mode, that boosts the signal amplitude to a maximum of 5 Vpp. With 2 markers per channel precise setup synchronization is guaranteed while the full 16 bit output resolution is maintained.
-
product
Vector Network Analyzer
MVNA-8-350
MVNA-8-350 is a vector network analyzer (VNA), an instrument which measures the complex, or vector, impedance (a real and an imaginary part of the impedance or an amplitude and a phase of the microwaves) in the millimeter and sub-millimeter frequency domain. It covers the frequency range from 8 GHz up to 1 THz.
-
product
9 kHz Highpass Filter
TBHPF1-9KHZ
9 kHz Highpass Filter for protection of spectrum analyzer or EMI-receiver RF inputs against high amplitude subharmonics and residual 50 Hz voltage in conducted emission measurement set ups
-
product
Phase Noise Analyzer and VCO Tester
FSWP
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
product
Radiation Portal Monitors
Baltic Scientific Instruments, Ltd
Radiation Portal Monitors (RPM) are fix-installed radiation detection systems designed for automated screening of pedestrians, vehicles and trains passing through the detection zone of RPM for presence of gamma and neutron radiation. The RPM alerts the security office and front line officer about the presence of radioactive and nuclear material and provides additional alarm associated information: type of alarm (gamma, neutron or both), relative amplitude of the alarm, etc.
-
product
Radar Core Chips
Macom Technology Solutions Holdings Inc.
Multifunction GaAs and Silicon MCM designed for communication radar and weather applications. MACOM Core Chips deliver a complete transmit/receive function with phase and amplitude control.
-
product
HandyScope HS5: 100 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 10MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-110XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 100 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
High Voltage, High Current Linear Amplifier
P200
The P200 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
product
Unipolar High Voltage Linear Amplifier
P150
The P150 is a general purpose linear amplifier having a fixed amplification of 20 times and capable of unipolar high voltage output of +150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to +10 V can be used as an input device. The amplification can be set to x15 (or other value) on request.
-
product
Single Channel High Voltage Linear Amplifier
A600
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Portable RF Signal Generator
ACE 5400
The ACE 5400 portable RF signal generator has four carriers that can be activated individually or in any combination. Each frequency and amplitude is adjustable by the user. The ACE 5400's basic and straight forward performance is perfect for applications that require a precise, stable RF stimulus. Applications: Testing and aligning CATV return bands; Great for institutional networks.
-
product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 58624
- Modifies 68 IF signals between input and output- Up to 80 MHz IF bandwidth- Four 200 MHz 16-bit A/Ds- Four 800 MHz 16-bit D/As- 68 DDCs and 68 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Lightning Current Generator
Shanghai Guantu Technology Co., Ltd.
The lightning wave impulse current generator is an impulse current generator that generates a simulated lightning current waveform . Its working process is as follows: first, the transformer charges the capacitor bank through the silicon pile, when the charging voltage reaches a predetermined value, the spark gap is triggered, and the capacitor is discharged through the total inductance and total resistance of the circuit. When the resistance is greater than or equal to the critical damping value, a unidirectional impulse current wave is generated in the circuit. When the resistance is less than the critical damping value, an oscillating impulse current wave is generated. The magnitude of the impact current amplitude is related to the circuit parameters. When the capacitance value and charging voltage are the same, the smaller the inductance value, the greater the current amplitude. In order to obtain as much current as possible, a pulse capacitor with a small inductance value is usually selected, and the total length of the connecting line should be as short as possible when arranging the main capacitor, so that the total loop inductance value can be reduced as much as possible.
-
product
Instruments
Monitoring applications record and log only those key events when user-defined threshold criteria are exceeded. These applications are valuable when users have established “not-to-exceed” event amplitudes associated with their products and cargo.
-
product
HandyScope HS5 + SureConnect: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XMS-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/UL/S/C , Programmable Amplitude Balance
LS-16A-R1-24SLUSC
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
Coaxial Power Dividers
A coaxial 2-way power splitter with a typical insertion loss of 1.2 dB at each output port and a typical isolation of 16 dB across the frequency range of 1 to 18 GHz. The power splitter has a nominal power handling of 30 W (CW) and a typical amplitude unbalance of ±0.4 dB. The return loss for all ports is 13 dB typical. The RF connectors of the power splitter are female SMA connectors.
