Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Solid State MUX, 2 bank, 80 channel
40-680-005
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Industrial Vibration Sensor
IVS-500
The new IVS-500 Industrial Vibration Sensor is the key to fast acoustic quality inspection, structure-borne noise analysis and reliable pass-fail decisions. This Laser sensor measures reliably, in demanding industrial environments, without contact and therefore without wear and on virtually all surfaces. Costs and yields are therefore optimized by reducing false rejects in the production and assembly process. The simple setup and ruggedized sensor design of the IVS-500 enable a smooth integration into production test systems. Complemented with the software tool QuickCheck, Polytec offers a comprehensive solution for reliable pass/fail analysis.
-
product
tna intelli-weigh®
omega series
tna intelli-weigh® omega series of multi-head weighers brings the ultimate efficiency, simplifying your weighing process while running wet or dry applications. Our advanced hygienic design goes beyond industry standards with stainless steel construction and waterproof scales, which makes maintenance and product changeovers fast and easy. The tna intelli-weigh® omega series of weighers is eco-friendly helping reduce product waste and is made with fewer parts that need changing due to wear and tear. A modular actuator unit provides quick troubleshooting, should you ever need it. IP rated 54.
-
product
6, 8 GHz, 4 Channel Programmable Attentuator
QPA8, PA8
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InP1012-30
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-30GHz
-
product
CMP Tester
CP-6
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
product
Core Loss Testers
S30 and S30S Series
Stacks built with punched laminations can have a lot of quality issues. Even though the lamination material is tested in sheet format before any process, that alone is not sufficient to guarantee good quality stators. Wear and tear of the punch, bad welding, bad insulating coating in annealing add to the magnetic losses in the stator. It is always advisable to test the stator core in it's final format before winding to ensure good quality throughout the production batch.
-
product
ICP-OES Spectrometers
ICP-OES spectrometers measure the concentration of elements from ppb to % using de-excitation of atoms and ions in a plasma. The robustness of our Ultima ICP spectrometers makes them ideal for applications common to mining, chemicals manufacture, salt production, wear metals in oil analysis, petrochemical, metallurgical production and precious metal refining.
-
product
Leak Detection Oil
The faster, safer and easier way to locate even tiny leaks in industrial air conditioning and refrigeration systems. Lumirati® bottled dyes can be poured directly into any AC&R system. The dye can remain safely in the system to confirm repairs and perform future preventive maintenance checks. Lumirati® Leak Detection Oil is the only dye that gives you all these benefits:- Universal dye that is compatible with all refrigerants and lubricants- OEM-approved by major compressor, refrigerant, lubricant and AC&R equipment manufacturers- Co-solvent free so dye will not impair lubricant properties, which could lead to excessive wear or damage to the system components
-
product
Data Loggers
Identify trends in vibration, noise, temperature, humidity and more that can be indicative of component wear and/or influence machine performance with help from PCE Instruments' data loggers.
-
product
Torque Tester
TorqueLab® LTT-Series
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
product
ICI Pilling and Snagging Tester
TESTEX Testing Equipment Systems Ltd.
ICI Pilling Box, to rapidly replicate pilling or snagging on fabrics in a fraction of the time due to normal wear. ICI Pilling and Snagging Tester complies with ISO12945-1, BS 5811, JIS L1076, etc. Contact us for more information about pilling test method.
-
product
PXI Solid State Very High Density Matrix
40-501-001
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InPD1012-40
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Test board with K-connectors can be providedDC-40GHz40+ Gbps
-
product
Brush or Sponge Pilling Tester
TESTEX Testing Equipment Systems Ltd.
Brush or Sponge Pilling Tester, To determine the pilling propensity and simulate normal wear of knitted and woven fabircs used in apparel and automotive interiors by brush and/or sponging specimens together in a circular motion to form pills. Brush or Sponge Pilling Tester complies with ASTM D3511, FORD BN 12-4, FORD BN 108-03, etc.
-
product
SafeOne RF Safety Monitor
The SafeOne is a RF Safety Monitor covering the requirements set forth in WHO ICNIRP specifications. It has a very wide frequency range covering 30MHz to 10GHz, which makes it suitable for use in almost all antenna installations. Due to the innovative lightweight design, technicians can wear this at all times, without the need to constantly be observant of the state of the instrument. The SafeOne is powered with standard batteries, with 250 days of continuous operation.
-
product
Deluxe Durometer with Case
52-50546
Longacre Racing Products, Inc.
Tire hardness has a huge affect on your car's performance. A tire too hard won't bite and a tire too soft may wear quickly or even ball up. Also tire hardness changes during its life cycle. To run your best you must keep track of all your tire's hardnesses.
-
product
Starter and Alternators
MSG Equipment team of professionals recommends you to carry out all repair operations in the car workshops without using your own hands. Self-repair often becomes the cause of chronic malfunction. Surely, you saw these grief-drivers who hang around day and night under the hood of their car. The desire to save on a trip to a service center by car turns into permanent breakdowns, rapid wear of parts and, consequently, frequent financial expenses.
-
product
Roughness Testers
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
product
Water Vapour Permeability Tester
TF165
TESTEX Testing Equipment Systems Ltd.
Water Vapour Permeability Tester, to determine the resistance of textiles and textile composites (particularly action wear fabrics) to water vapour penetration. Water vapour permeability tester consists of 8 containers with water reservoirs; a standard permeable fabric cover, sample holder ring and precision drive system.
-
product
Tribometer
With decades of experience in tribology, Anton Paar provides you with the widest range of tribometers on the market. Tribology is the science and technology of interacting surfaces in relative motion, the practice of studying friction, wear, and lubrication. What you are looking for is a solution tailored to your needs, which is versatile and robust enough to handle the range of materials you are interested in.
-
product
Tribometer
NANOVEA Tribometer is a powerful and adaptable all-in-one friction and wear tester with the widest range of testing and environmental modules on the market. The simple design of a NANOVEA Tribometer allows for fast interchangeability to accommodate for any research need and requirement or standard.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InPD1012-60
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Test board with K-connectors can be providedDC-60GHz40+ Gbps
-
product
Friction Player
FPR2200
The friction coefficient is measured by the pin-on-disk method. Also, by measuring the coefficient of dynamic friction, surface destruction occurs due to wear and changes in the coefficient of dynamic friction occur .This machine is the latest model that was created by realizing various measurement modes, improving data resolution, and pursuing ease of use based on the achievements cultivated in the friction and wear tester that we have manufactured and sold in the past.
-
product
Sliding Peel Strength Tester
OST3000
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
product
Safety Proximity Sensors
Leuze electronic GmbH + Co. KG
With their encapsulated and contactless design, safety proximity sensors are insensitive to contamination and humidity. They operate free from wear and also have a long life expectancy, even with frequent operating cycles. They are also used wherever it is difficult to precisely guide the moveable protective device. All devices feature a high-strength plastic housing. Furthermore, the devices with RFID transponder provide maximum protection against tampering.
-
product
Power Circulation Type Tire Wear Tester
This test machine is a tire wear test device that employs an electric servomotor power circulation system.
-
product
PXI Solid State MUX, 20 bank, 8 channel
40-680-001
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Volumetric Sample Preparation Station
APS‑7450V
The APS-7450V is made to keep pace with the increased speed of wear metals labs, where analysis time is often shorter than 30 seconds per sample, by simply and quickly handling the dilution step in less time.
-
product
Blast Nozzle Gauge
103
The Elcometer 103 Blast Nozzle Gauge measures the orifice size of an abrasive blasting nozzle. This gauge is used to determine the nozzle orifice wear which leads to low nozzle pressure and decreased efficiency in its performance. Nozzle orifice wear results in decreased productivity and increased abrasive media consumption.
-
product
Floor Conductivity Tester Hand Crank
LA-1 HC
LA-1 HC Floor Conductivity Tester Hand Crank is an easy-to-use meter developed for accurately testing the conductivity of floors and equipment. The LA- 1 must be used regularly to monitor proper conductivity with NFPA code # 99. Regular use of the LA-1 will establish and maintain procedures for the proper maintenance of conductive floors, eliminate fire hazards, and provide a static free environment. A hand crank AC type generator provides a rectified DC test potential. Additionally, there are no brushes to wear out. The LA-1 has an easy-to-read scale that is selectively expanded electronically to assure accurate readings over the entire range of the instrument and the scale has a length of 3.75. This is 42% longer than typical competitive testers. The LA-1 uses 500V DC to test the resistance (in ohms) between two points. (NFPA Code #99) The meter comes ready-to-use (tin foil must be applied to bottom of weights). Simply follow the instructions for use and instantly obtain an accurate measurement. Choose electric or hand powered model.
