Filter Results By:
Products
Applications
Manufacturers
Test Bench
worktable including instrumentation, fixturing and unit under test.
See Also: Test Benches
- InterWorking Labs, Inc.
product
SilverCreek SNMP Tests
Set up in less than five minutes - Windows or LinuxCustomize tests via Wizards, Script Generators, and moreAutomate operation with unambiguous test resultsIntegrate with other test harnesses and test toolsIncludes conformance, compliance, vulnerability, robustness, stress, and performance testingInvestigate failures and quickly resolve them with powerful diagnostic and analysis tools
-
product
Three Phase Phantom Load Test Bench
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
Integrated Test Facility
ITF
The ITF, located in El Segundo, California, has multiple test stations to enable parallel testing and significantly streamline program test schedules. More than 25,000 square feet are available for integration and test activities, including a 10,000-square-foot Class 10K clean room. Our facilities feature thermal vacuum chambers and test stations to support optical alignment, warm optical bench testing, and hardware integration.
-
product
Multifunction Calibrators
These field and bench calibrators source, simulate, and measure pressure, temperature, and electrical signals with exceptional precision. They can automate calibration procedures, store data, and even calibrate and troubleshoot HART-compatible devices. Our bench calibrator can even be used to calibrate our field calibrators. Also find here 5.5- and 6.5-digit bench multimeters for to assist with a variety of general test and calibration applications.
-
product
Pitot / Static Tester for Laboratories and Workshops
ADSE 741
The ADSE 741 is a complete high performance three channel Ps, Pt and AoA stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, pneumatic AoA (Angle of Attack) indicators, MACH-meter, air data computers, specific probes and sensors.The high precision embedded sensors enable the ADSE 741 to be used as a pressure standard.The user interface is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
product
Load Cell Power Supply Module
MODEL PSM-F10
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
product
Test Solution Offering BER Testing
Eye-BERT Micro LR
The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.
-
product
DC Power Analyzer, Modular, 600 W, 4 Slots
N6705C
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to control a collection of instruments and take useful measurements because all functions and measurements are available at the front panel. For even greater control and analysis functions, the DC Power Analyzer can be used with the 14585A Control and Analysis Software. When automated bench setups are required, the N6705C is fully programmable over GPIB, USB, LAN and is LXI Compliant. 14585A Control and Analysis Software
-
product
S500 Test Solution
The S500 Bench Test Equipment (BTE) is customized to test the Line Replaceable Unit (LRU) to determine the faulty Lowest Level Replaceable Unit (LLRU). Once a faulty LLRU is discovered, a separate application program specifically designed for the LLRU is executed to further isolate the fault.
-
product
MCB Thermal Verification Test Bench
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
product
Common Rail Injector Test Bench
Nanyang NanTai Experimental Equipment Co.,ltd
It adopts advanced frequency conversion technology and digital technology with automatic and manualdouble control for the rotation speed, temperature and count.Equipped with displacement sensor, it can test different kinds of mechanical fuel
-
product
Customized Thermal Management Test Bench Solutions
Our IPEtec test bench engineering business unit plans and provides customized test bench solutions for the development and validation of automotive AC components. We offer a full range of test benches and media-supply modules for the automotive developer’s thermal management needs. Moreover, we support the development of new cooling systems for hybrid power trains, for battery and engine cooling. New hybrid power trains are opening up additional fields of heat-pump technology development aimed at optimizing the energy balance of automotive air conditioning.
-
product
PCI-X Carrier For AMC Modules
PCI102
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
product
Atec Dyna
Macro-instruments an innovative concept : ultra-simple interface between the test bench and the equipment being tested, Software-controlled macro-instrument, Generic TUA (Test Unit Adapter) incorporated in the bench
-
product
KWH Meter Test Bench
This test bench is widely used in electrical and engineering sector for varied testing applications.
-
product
Test Benches DC
Combined with a power source system e.g. MTS750 this test bench is used as a DC meter test system with 40 test positions.
-
product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
product
T3DSO3000HD Series Oscilloscopes
T3DSO3000HD Series
The Teledyne Test Tools T3DSO3000HD Oscilloscopes feature four channel bench models with analog bandwidth options of 200 MHz, 350 MHz, 500 MHz and 1 GHz each with 12 bits of vertical resolution. Each model offers a maximum sample rate of up to 4 GS/s sample rate and a maximum memory up to 400 Mpts. The series comes with all serial data trigger & decode options as standard alongside Power Analysis Bode Plot and Sequence Mode capabilities.
-
product
500 HP Complete Bench Hydraulic Test Center
HTC-500
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 500 hp (373 kW) HTC Complete Bench is for the dealer that services components from a predominately larger machine size mix such as large mining machines and large excavators. The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
product
Phoenix Modular Facilities
The lean design and unparalleled portability of Atec’s Phoenix™ Series Modular Test Cells have shifted the paradigm for engine testing. The Phoenix Cell delivers the functionality of traditional brick and mortar engine test cells with the added benefit of efficiently transported equipment. It offers our customers a flexible, low-risk, value-driven engine test cell solution for their most important equipment. The Phoenix Modular Cell is the premium solution for turboshaft, APU, and test bench applications. It can be particularly attractive where construction in certain settings may be difficult, or where usages may be short term or temporary at the location. No matter the logistics, Atec has a Phoenix™ Series Modular Enclosure to meet your needs.
-
product
Functional test
Maschinenbau Haldenwang GmbH & Co. KG.
Test bench for small vehicles with 2 wheelsRoad load simulationDetermination of maximum speedMeasurement and evaluation of speed, speed, distance traveledDisplay of wheel power at test speedDisplay on your PC monitorExpression of test resultsCustomer and vehicle databaseEuro system console MCD 2000 with switching elements for roller setPort for external devices
-
product
Test Bench
BERTA
OPAL-RT’s BERTA test bench is a safe, reliable and portable test bench for speed governors, turbines, voltage regulators (AVR) and power system stabilizers (PSS). Equipped with a high-performance real-time simulator programmed with world-renowned RT-LAB software, the BERTA Test bench enables users to easily and comprehensively test real generating units in the power plant, synchronized and transmitting power to the main grid and/or on real controllers connected to a virtual generating unit in laboratory.
-
product
Aircraft Test Set
CA-2100S-07
The CA-2100S-07 is a bench mounted, modularized and computer based test set used to service all types of aircraft electronics. It simulates the aircraft environment and replaces a myriad of specialized test fixtures found in the industry.
-
product
High Precision Energy Meter Test Bench
SY8330
Hong Kong Songyang Industrial Ltd.
SY8330 Series Three Phase Energy Auto-calibration System is a new generation, high precision, multifunctional energy meter calibration equipment. It uses the international’s most advanced technology and components available in 90 decade. It can be widely used to calibrate different kind of single phase energy meter both channel & three phase energy meter or multifunction power meter.
-
product
Detector Test Bench
RTB 3000
The RTB 3000 Detector Test Bench from Santa Barbara Infrared (SBIR) is a flexible integrated IR detector test station for evaluation of single element detectors, linear arrays, and focal plane arrays. The RTB 3000 provides the radiometric stimulus necessary to perform accurate IR detector testing in both laboratory and production environments.
-
product
Water Meter Test Bench
VM-DN15-25
Shanghai Powoo Industry Develop Group Limited
The tester bench is the necessary measure instrument for the test and repair of water meter in metrological service, water meter manufacture, water supply company, industrial and mining establishments.
-
product
DMX Tester
DMXter 2U
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
product
Portable Test Bench for Single Phase Energy Meter
SY2100
Hong Kong Songyang Industrial Ltd.
The new SY2100 series Portable electricity meter test equipment, designed from new DIGITAL WAVE COMPOUND TECHNOLOGY and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
product
Closed-Loop Servohydraulic Test Bench Control System
Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.
-
product
Torque Reaction Sensor
BMX
Meeting the demands to test multiple torque ranges for various torque tools used in production, maintenance and calibration labs, the versatile torque sensor is used in conjunction with a torque tester. The torque sensor is a bench mounted calibration instrument designed for torque wrench calibration, torque screwdriver calibration, and electric & pneumatic screwdriver calibration. Controlling torque is quintessential for companies to ensure their product's quality, safety and reliability isn't compromised.
