Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
HandyScope HS5: 50 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 5MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-055XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 50 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
Digital Control VGAs
Analog Devices digital controlled variable gain amplifiers provide discrete levels of gain control over a fixed number of control bits for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust the amplitude of a signal in real time, which is critical for a number of applications involving ultrasound, speech analysis, radar, wireless communications, and instrumentation. We also offer a portfolio of voltage controlled VGAs to provide you with continuous gain control over a wide dynamic range.
-
product
Fatigue Testing And Certification
Fatigue engineering is subject to uncertainty, and data from well executed tests are used to validate conclusions made by analysis and to provide a basis for structural certification. Our staff have extensive experience in testing materials and components under slowly varying, static loads, and under rapidly varying cyclic loads. Tests under static loads are used to assess material properties or to assess the load-deformation behavior of structural components. Tests under cyclic loads provide time to crack initiation, time to failure, or measurements of crack growth over time. We have extensive experience in measuring fatigue crack growth behavior in metallic materials. Past programs have measured crack growth with microscopy and photogrammetry at the surface, cracked area with direct current potential drop, and through-thickness crack profiles with quantitative fractography. By assessing crack growth with a variety of experimental methods, we enable robust analysis validation for cases of complex cracking. Our capabilities in fatigue engineering allow for careful design of a fatigue test program. Whether the tests use constant amplitude loading or an irregular loading spectrum, we specialize in engineering the test that meet your needs. Much of our experience is in non-standard test programs, which require engineering to optimize the test setup. Few others match our capability and experience in fatigue test engineering.
-
product
3671 Series Vector Network Analyzer (100kHz - max.43.5GHz)
3671
3671 series network analyzer provides frequency response, single-port, response isolation, enhanced response, full-dual port, electronic calibration etc. Offer various display formats, such as logarithmic amplitude, linear amplitude, phase, group delay, Smith chart and polar coordinates. 3671 series can accurately measure the amplitude frequency characteristics and phase frequency characteristics and group delay characteristics of microwave network.
-
product
PCIe Direct Digital Synthesizer
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.
-
product
Spectrum Analyzers
PeakTech Prüf- und Messtechnik GmbH
Spectrum analyzers are used to display the amplitude distribution over a certain frequency range.
-
product
SMT Surface Mount MEMS High-G Shock Accelerometers
Piezoresistive MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.
-
product
Single Axis AC Magnetic Field Sensor
MGC-1
Macintyre Electronic Design Associa
The MGC-1 is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1 amplitude response is insensitive to the frequency of the field over its 5 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
product
Single Axis AC Magnetic Field Sensor
MGCH-2
Macintyre Electronic Design Associa
The MGCH-2 is the lowest noise, highest sensitivity single axis AC magnetic field sensor available for the measurement of sub radio frequency fields. Because of its innovative design, the MGCH-2 amplitude response is insensitive to the frequency of the field over its 10 Hz to 100 kHz frequency band. Accuracy at 10 kHz is 0.1 dB, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
product
Audio Frequency Sweep Generator
Feature:*Auto and manual operation selectable*Ouput power:20W.40W.60W.100W.200W*Sweep time selection*5 digit LED display for frequency 4 digit display for voltage amplitude observation of synchronous output*Power supply:AC 220V(110V Optional)
-
product
Adaptive Relay, Virtex-6 FPGA - 3U VPX
Model 52624
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Astronics PXIe-2461, 235 MHz FrequencyTime Interval Counter
784197-01
PXIe, 42 V, 2-Channel PXI Counter/Timer Module—The Astronics PXIe‑2461 is a high-performance counter/timer module that provides easy-to-use automatic measurement functions, including phase, pulse, peak, rise/fall time, time interval and ratio measurement, all with high resolution. It features nine digits per second resolution, programmable measurement timeout, and nine different arming modes. You can set the Astronics PXIe-2461 to measure timing and amplitude characteristics in one of two voltage ranges: ±5.1 V or ±42 V.
-
product
Event Detector
The Event Detector automatically extracts sound events from an entire sound file according to the user's event specifications. The user digitizes sound data into a continuous sound file, then configures the Event Detector for the events of interest. Detection is based on spectral, temporal, and amplitude criteria. The detector scans the entire file, identifying the desired events and extracting them to individual sound files or measuring their parameters. Detected events can be immediately analyzed in SIGNAL to measure, count, compare, classify, time-stamp, and store sound events and sound parameters. The Event Detector is a module inside SIGNAL and requires SIGNAL to operate.
-
product
Coaxial Power Dividers
A coaxial 2-way power splitter with a typical insertion loss of 1.2 dB at each output port and a typical isolation of 16 dB across the frequency range of 1 to 18 GHz. The power splitter has a nominal power handling of 30 W (CW) and a typical amplitude unbalance of ±0.4 dB. The return loss for all ports is 13 dB typical. The RF connectors of the power splitter are female SMA connectors.
-
product
Transmitters
Seismic transmitters provide a 4-20mA DC signal output proportional to the vibration amplitude, and are ideal for applications where a PLC, DCS, or other automation system will be used instead of a stand-alone vibration monitor. Metrix offers seismic transmitters with a wide variety operating temperatures, frequency responses, scale factors, case materials, connector types, mounting options, and hazardous area approvals.
-
product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
product
CT / PT Analyzer
CTPTA-504
UDEYRAJ ELECTRICALS PRIVATE LIMITED
UDEY ‘CTPTA-504 is a comprehensive CT and PT analyzer. It’s constant voltage and current is highly stable. DSP system controls the constant voltage and current source output and amplitude. This source generates AC of 0-125V and or DC of 0-0.5A current to sample CT. The DSP system besides controlling the sources, also samples data and communicates with the internal computer. Display screen is large LCD with touch pad. The analyzer is highly accurate with high noise immunity and is very user friendly.
-
product
Ultra Low-Loss Cable Assemblies
dB Miser
Cost-Effective, High-Performance Solutions for Low Loss ChallengesConsider dB Miser™ ultra low loss cable assemblies. High performance materials, careful attention to design detail, and stringent process control yields:- Ultra low insertion loss over the specified frequency range- Excellent amplitude stability with flexure- Stable performance over operating temperature range - Increased shielding effectiveness - Greater connector retention
-
product
Spectrum Analyzers
Frequency range:0.15∼500MHz(SA5005/SA5006T) 0.15~1050MHz(SA5010/SA5011T).Amplitude range:-100~+13dBm.Tracking generator(SA5006/SA5011T).Output level range:-50~+1dBm(in 10dB steps and var.)
-
product
2 Channel 1GSPS 8 Bit ADC Card in FMC
FM582
Sundance Multiprocessor Technology Ltd.
The offset adjustment does not clip the signal at the highest range (+/- 5V). That is why the “max input signal amplitude” has been specified as 10V, even though the selection of signal ranges only goes up to 5V. This way, a +10V pulse with -5V offset could still be digitised without clipping.
-
product
Digital Phase Shifter
Analog Devices digital phase shifters change the phase of RF, microwave, or millimeter wave signals while providing no amplitude change. They are used in a variety of applications, including RF PA linearization/RF distortion, amplitude and phase modulation, variable attenuators, and fiber optics.
-
product
Dual Polarized Antennas
Dual polarized horn antennas are offered as both standard and custom models with rectangular waveguide interfaces for both horizontal and vertical ports. These dual polarized horn antennas support both linear and elliptical polarized waveforms. When the antenna receives a circular polarized waveform, equal amplitude linear polarized waveforms are output at both horizontal and vertical ports. When two equal amplitude linear polarized waveforms are input into the vertical and horizontal ports, the antenna will transmit a circular polarized waveform. The listed models offer 15 dB nominal gain and 33/28 degrees typical half power beamwidth at the center frequency of the band. They also exhibit 40 dB typical port isolation and 35 dB nominal cross polarization. These antennas cover full waveguide bandwidths within the frequency range of 8.2 to 110 GHz. In addition to the models listed below, models with 10, 20, 23 and 25 dB gain and other frequency bands are also available.
-
product
Arbitrary Function Generator
FGX-2220
FGX-2220 is a full two-channel function generator of 20MHz by the DDS system. Each channel separately can set all of the functions, such as waveform, frequency and amplitude.
-
product
Smart Sensorgrid NG
Smart Sensorgrid belongs to the smart sensor family devised for on-line monitoring of diagnostic quantities in electrical assets. It provides traffic-light alerts to SCADA systems / asset and maintenance service. Smart Sensorgrid is a state-of-art PD analyzer, exploiting the TECHIMP T-F Map technology (patented). Such feature allows noise rejection and automatic alarm warning based on amplitude and repetition rate trend relevant to statistical parameters. The PD sensor, a HFCT, is integrated in the smart sensor body.
-
product
Adaptive Relay, Virtex-6 FPGA - XMC
Model 71624
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Time Domain Sensors
TDS
Schmid & Partner Engineering AG
Time Domain Sensor (TDS) probes are miniaturized fully isolated active optical magnetic or electric field sensors operating in the frequency range from 10MHz to 6GHz. TDS offers unparalleled sensitivity for EM measurements resolved in the time and frequency domains while maintaining all amplitude and phase information.
-
product
Coherent Synthesizers
Innovative Technical Systems has developed high-performance agile microwave synthesizers with truly phase-coherent frequency switching at any step size. These synthesizers offer frequency coverage from 250 MHz to 18 GHz (ACS-25018) or 850 MHz to 18 GHz (ACS-85018) and frequency resolution under 0.1 Hz. The agile design offers typical switching speeds of less than 300 nsec and programmable amplitude from 0 to +10 dBm from frequency-to-frequency. Spurious performance is typically <-70 dBc. A versatile waveform table design is implemented that allows frequency, amplitude, and output markers to be defined for each step in the table. Waveform table lengths up to 256K are supported.
-
product
Dual Channel Driver Card
40461
Two channels of 8 to 10 MHz drivers (25 V amplitude). The output voltage range is ±25V, with independent high and low voltage settings. The inputs to the Card are optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel as low as one nanosecond increments.
-
product
Multiple Signal Generator
1. Two Signal Output Ports2. Frequency Range:10 Hz ~ 100 kHz and 1 kHz ~ 15 MHz3. Output Waveforms:Sine, Triangle, Square,TTL Pulse, AM, FM4. Amplitude:10 Vpp(Max)5. Built-in LCD CountersDC Power Supply：1. Triple Outputs (One Variable, two Fixed Output)2. Constant Voltage Operation3. Low Ripple and Noise4. Built-in 3-Digit Voltage Indicator5. Overload Protect6. Overload Buzzer Indicator
-
product
Sensors
To measure machinery or structural vibration, a transducer is needed to convert the mechanical motion into an equivalent electrical signal. Each sensor has distinct advantages in certain situations and limitations in other, so it is important to select the most suited transducer or sensor for your job. Equally, important is selecting the appropriate parameter of vibration amplitude for measurement. IRD® has a wide range of transducers and accelerometers available to help you obtain accurate, reliable data, whether your concern is vibration monitoring, analysis, or dynamic balancing.
