Filter Results By:
Products
Applications
Manufacturers
ECU
a vehicle system's Electronic Control Unit.
See Also: ECU Testing, ECU Simulation, Vehicle Electronics
- Pickering Interfaces Inc.
product
PXI Thermocouple Simulators
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
product
Oxygen Sensor
KS60003
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
TPMS Tool
TPA 300
The Bosch TPA 300 is a comprehensive TPMS tool designed for sensor programming, activation and ECU reset. The full-color, intuitive interface guides the user when replacing and servicing TPMS sensors. When paired with a compatible Bosch diagnostic scan tool, like ADS 325 or 625, users can reset the ECU in less than two minutes. The TPA 300 supports all known OE and aftermarket programmable sensors for all light vehicles. Frequent updates allow new features, vehicles and sensor coverage to be added regularly.
-
product
ECU & Bus Interface Modules
ES500
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
product
Visualize & Analyze Measurement Data Software
vSignalyzer
vSignalyzer is a convenient tool for efficient evaluation and analysis of all types of measurement data. Its functional features range from extensive options for data visualization to manual andautomated analysis and reporting. The measurement data that is logged during network development, network analysis and ECU calibration may be read in from various file formats.
-
product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
OBD2/J1708/J1587 Simulator
DFLSOBD2
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
product
PN009 – ECU – Diagnostic
*Allow to read and write EEPROM EDC15, EDC17 (BOOT MODE), SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806.*Read and modify of counter – EDC16, EDC17(BOOT MODE), SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806*Read and change PIN EDC15, SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806*Read and change EEPROM with EDC15 and make OFF
-
product
ECU Interfaces
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
product
Universal Solution for Model-based Calibration Software
INCA
INCA tools are used for ECU development and test as well as for validation and calibration of electronically controlled systems in the vehicle, on the test bench, or in a virtual environment on the PC. The tools are used worldwide in over 20,000 installations in development and production projects.
-
product
ECU Software Download Stations
Jackmark Engineering design & manufacture ECU software download stations also known as flash stations, for several industry sectors including automotive, agriculture & utilities. The custom designed stations in either a single unit or multiple stacks provide a secure & reliable system of downloading software to electronic control units. Units are ‘locked in’ during the download phase with visual indicators of download status.
-
product
CAN-BUS Shield
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output it to a screen to make an in-dash project.
-
product
Car Oxygen Sensor
KS60124
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Helicopter FADECs
The EMC-100 is dual channel Full Authority Digital Engine Control (FADEC) system, designed for helicopter turboshaft engines. The electronic control unit’s (ECU) primary channel provides precise engine power management and rotor speed control throughout the operational range of the engine. The reversionary backup channel provides full mission capability should a primary system failure occur.
-
product
Autonomous Driving AI Decision Making ECU
ADM-AL30
ADM-AL30 is dedicated to Autonomous Driving Applications. Powered by Intel® 12th Gen Core i9/i7 CPU and the NVIDIA RTX 4000 SFF Ada GPU, this AI computing platform can process huge amounts of data and make crucial decisions for autonomous vehicles. Equipped with 2 x 10G Base-T and 8 x 1G Base-T1 automotive ethernet ports, as well as 8 x CAN FD and 4 x CAN 2.0 interfaces, it seamlessly integrates into any automotive ecosystem. Plus, its ISO 16750-2 and ISO 7637-2 ensure reliability and safety under the most demanding conditions.
-
product
Electronic Engine Controls - FADEC
The EMC-100 is dual channel Full Authority Digital Engine Control (FADEC) system, designed for helicopter turboshaft engines. The electronic control unit’s (ECU) primary channel provides precise engine power management and rotor speed control throughout the operational range of the engine. The reversionary backup channel provides full mission capability should a primary system failure occur.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Engine Performance/Endurance Test System
Various types of test system as follows can be built up in combination with measurement control equipment and peripheral instruments (fuel flow meters, actuators, temperature control device, combustion analysis system, ECU monitor, OBD, sound and vibration measurement instruments, emission analyzer, smoke meter etc.)·Traveling fuel economy test·Gas emission test·Output performance test·Deterioration/endurance test·Combustion analysis·Sound source probing
-
product
ECU Calibration
Designing an Electronic Control Unit (ECU) is only the beginning. The features in ECUs, such as Powertrain Control Units, are quickly becoming more complex and offering more features. Thousands of variables are now provided for the engineer to modify during the in-vehicle calibration phase, and fine tuning them is as complicated as it is critical. Calibration tools significantly impact the efficiency and effectiveness of the ECU development process. These tools are typically comprised of PC-based software to perform the adjustment of the variables and an ECU hardware interface to provide the connection of the software to the controller. Teams must be able to measure and time-align relationships of inputs and outputs and make real-time modifications.
-
product
Lambda Sensor
KS60121
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Auto Oxygen Sensor
KS60004
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Sensor Signal Emulator
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
product
Ferrari Oxygen Sensor
KS60113 - Ferrari
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Oxygen Sensor
KS60145
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Programmer VVDI MB TOOL
*learning ELV*Read and write CGW / ZGW – OBD*programming and making new keys NEC SMD*generating files keys without time delay (all ROMs)*making new keys BE through IR*read password from BE keys through IR*making new keys modułów throught connector (ECU, Ism, elv, 7g tronic)*EZS lock – making new keys through IR*EZS data edition*With power Adapter very fast counting password on some models (all keys lost)*erasing „fatal error” in ELV
-
product
Iveco Oxygen Sensor
KS60113 - Iveco
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Wireless Data Logger
EVA100
The new highly integrated measurement system "EVA100" is supporting Power Supplies, SMU( 4 quadrant DC Signal Measurement Units ), Pattern Generators, Arbitrary Waveform Generators, Digitizers and Oscilloscopes necessary for complete analog / mixed-signal / sensor / digital IC devices and Modules including Electronic Control Unit (ECU) for automotive evaluation and measurement.This new measurement system allows engineers quickly to build their own measurement environment without combining several standalone instruments.
-
product
OBD Protocol Diagnostics
Our innovative OBD Protocol Diagnostics comes with diagnostic break-out boxes and CAN network testers which can expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test ECU signals.
-
product
Car Oxygen Sensor
KS60044
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Electrodynamic Shock Test System
FS SERIES
The system can test the sensor and ECU for an airbag and also reproduce the shock by assuming an automotive collision and full-scale crash. The system can be incorporated into the production line for total inspection. It can maintain the operating quality of the airbag to make a contribution to lifesaving against a traffic accident.
