Filter Results By:
Products
Applications
Manufacturers
- Applied Instruments, Inc.
product
Return Band Alignment System
6103/6106
Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106).
-
product
Microcomputer Three-phase Relay Test Set
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations.
-
product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
product
NI STS
RF Test and Measurement Solutions, LLC
RFTMS is a leader in configuring systems to meet your needs, as well as designing load board, writing SW, and integrating the final solution. We do this for wafer test, packaged parts, and modules. RFTMS can address any level of integration that your parts employ, from a single functional block, i.e., Power Amplifier (PA) to System-on-a-Chip (SOIC). We test all sorts of RFICs.
-
product
Reverse Test Probe
I-Stop
The I-Stop Reverse Test Probe is a test accessory designed for use with most signal level meters and with the Trilithic 9580 Return Maintenance System. Screw the probe into a distribution tap's unused KS port and a spring-loaded "stinger" connects a 20 dB resistive test point circuit to the hardline.
-
product
Functional Testing
Whatever your functional testing requirement, whether analogue, digital, or a combination of technologies, we have a solution. With over 2500 applications delivered in this field we have a level of experience that cannot be matched. Ensure the reliability of your product with our functional testing tools. Our functional test solutions range from completely standalone applications to those matched for our FLEX range of ATE test systems. Whatever your testing needs, we will help you choose the best option for you.
-
product
Relay & Protection Testing
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations. It is further necessary that these expanding testing capabilities be met with a similar improvement in the simplification of a test instrument’s user interface and software control.
-
product
VXI Digital Test Instrument
T940 Series
The T940 Series for the VXIbus provides the basis for a complete state-of-the-art digital solution at the subsystem level. The T940 is the solution for both legacy digital replacement and new test stations to be built for digital test including aircraft/ avionics, weapons systems, spacecraft, semiconductors and medical devices.
-
product
Digital Test Instrumentation
Di-Series™
The Di-Series tests all levels of integration from board level (SRA/SRU) to box level (WRA/LRU) units under test (UUTs), while maintaining full compatibility with previous generations of Teradyne instrumentation and systems. Excellent usability and reliability reduce programming and support effort, as well as straightforward upgrades of existing test program sets (TPS).
-
product
Semiconductor Test
Smiths Interconnect’s test socket and probe card solutions utilize IDI contact technology to ensure superior quality and reliability in semiconductor test applications. Our best-in-class engineering, development and technical expertise ensure support of automated, system level and development test platforms.
-
product
High Voltage Battery Test System
9300 Series
NH Research, Inc. (NHR) has released the new 9300 series, a higher-voltage / higher-power version of its popular single-channel 9210 series battery test systems. The 9210 Series provided a 12kW power module operating at 40V, 120V, or 600V and which allowed paralleling with similar systems to increase the power, whereas the new 9300 system provides a 100kW power module with a software-selectable high voltage range (1200VDC / 167A) and high-current range (600VDC / 333A) allowing for efficient testing of single-voltage and double-voltage Electric vehicle (EV) batteries as well as high-voltage Energy Storage Systems (ESS) used in grid-tied applications. The 9300 further extends NHR’s family of high-power battery test and emulation capabilities which are ideal for analyzing a battery performance under xEV drive cycles and grid-storage profiles such as PJM and time-shifting profiles. Like the successful 9200 and 9210 systems, the 9300 modules are independent allowing for testing of multiple batteries, each with a different test plan, power levels and start/stop times. When higher power is needed, the 9300 modules may be paralleled providing 200kW, 300kW or up to 1.2MW capability. This modular power capability allows a system to be sized to the power levels needed today while ensuring expansion capability should additional power be needed in the future.
-
product
Scienlab Battery Test System – Pack Level, 220 KW
SL1730A
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
product
AIM System Solutions
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
product
Hardy Shaker
HI-913
This Hardy Shaker provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting a test easier. A test can be conducted on a vibration transducer and manually recorded. Multiple tests are not saved; for multiple tests use the HI-903 or HI-803 units. The HI-913 is used for testing from 7 to 10,000 Hz, it offers adjustable frequency and vibration levels. This provides a reference source for verifying the accuracy of vibration transducers, connectors, cabling and instruments or instrumentation systems. The HI-913 has a ruggedized suspension system that can support heavy transducers (up to 800 grams - see frequency limits in the manual). The HI-913 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, Transfer
87222R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87222R is a low PIM transfer coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
PXIe-6547 , 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument
81011-03
PXIe, 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument—The PXIe‑6547 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 100 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6547 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
product
128 Channel Digital I/O Modular PXI Card
GX5733 Series
The GX5733 is a 3U modular digital I/O card that offers up to 128 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5733 offers the highest channel density and flexibility in the industry for a single-slot, 3U PXI plug-in board. 96 channels support TTL levels and an additional 32 I/O channels can be customized by installing one of Marvin Test Solutions' GX57xx series I/O modules. Alternatively, the remaining port can be configured to support 32 TTL channels.
-
product
Variable Power Supply
VS-10a
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
product
Digital Display Auto Circuit Tester
1676
Peaceful Thriving Enterprise Co Ltd
This is a DC voltage tester with smart over-voltage protection and warning for vehicle repair. As electrical system for vehicle becomes more complex, the tester is able to test voltage value, identify DC polarity from different background light color, positive / negative sign, and over-voltage level indication. Moreover, the special designed probe is able to help user to hook, piercing, and probing the wires.
-
product
Altitude Simulation
MEDAS
The MEDAS system is a compact altitude simulator that reproduces a wide range of environmental conditions. It allows for testing light- to heavy-duty vehicles, including Non-Road Mobile Machinery (NRMM). It is ideally suited for a range of testing applications, such as durability, RDE replication, emission tests and mapping as well as tests from component to vehicle level. The patented technology inside the MEDAS system allows dynamic changes on the simulated atmosphere with high accuracy. The system can also be moved between different test cells due to its compact design.
-
product
Electromechanical Transfer Switches up to 40 GHz
Fairview Microwave’s line of electromechanical relay transfer switches can be utilized for numerous applications to increase system level capabilities and can help simplify the overall design approach. With two input and two output ports, transfer switches can connect two different instruments with two devices under test. Additionally, they can be used as drop-out switches, for signal reversal or to bypass a component under test. These products are typically used in military communications and broadcast systems, SATCOM, test & measurement, instrumentation applications and are suitable for aircraft use.
-
product
BSD (Test Diagnostics)
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
product
Variable Power Supply
VS3
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
product
Backplane Test System
402LV
Very High Pin Count Level IV Backplane Test System. To ensure that Testronics maintains its leadership position as the premier supplier of backplane testers, we will be introducing our solution to testing high pin count / very large backplanes, the Model 402.
-
product
RightMark Memory Analyzer
RMMA
Before this test packet was created there was no proper software for measuring vital system parameters such as CPU/Chipset/RAM providing steady and reliable (reproducible) test results and allowing for changing test parameters in a wide range. Vital low-level system characteristics include latency and real RAM bandwidth, average/minimal latency of different cache levels and its associativity, real L1-L2 cache bandwidth and TLB levels specs. Besides, these aspects are usually not paid sufficient attention in product technical documentation (CPU or chipset). Such test suite, which combines a good deal of subsets aimed at measuring objective system characteristics, is a must have for estimating crucial objective platform parameters.
-
product
Test Cell Vibration Monitoring System
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
product
Micro Ohm Meter 200A
Micro Centurion II
Raytech Digital Micro ohm meter, Micro-Centurion II, was designed for high degree of accuracy to measure very low resistances. This technology was then packed into a portable test system to be used by apparatus manufacturers, rebuild shops, and electrical maintenance crews. This intelligent system has an easy to use operation screen, which allows quick selection of the current level and resistance level to be measured.
-
product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
product
LED Lighting Panel Tester
igentic® 821t
Growing demand for light emitting diode (LED) products combined with increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. Sterner Automation, a leader in LED test technology, provides solutions that address these specialized requirements, including the versatile igentic® 821t panel testing system. The igentic® 821t automated process combines advanced vision technology with flexible positioning and power-up capabilities to detect inconsistencies in individual LEDs at the panel production level. The resulting detection capabilities ensure that the highest standards are met while maintaining the capacity associated with today's high speed automated lines.
-
product
Offline MPEG Analyzer
MSight
Instantly jump to any stream location with fast seeking which makes navigation simple and easy. MSight Analyzer will jump to the exact location of any error identified in a compliance test to allow full inspection of all the stream data at that location. Complete coverage with support for VC-1, H.264/AVC, MPEG-4 part 2, MPEG-2, MPEG-1, and system level (program and transport stream analyzer features) in a single tool.
-
product
QAM DVB Analyzer
Wuhan Sunma Technology Co., Ltd.
QAM Analyzer designed for both installation and maintenance of HFC system. Measure and display main parameters in DVB testing (channel power, MER, BER, Constellation Diagram), signal level on any frequency, amplitude of the carriers singly in the whole system range, and etc. The Analog, QAM and FM channel can be set and tested efficiently; it also supports HUM measurement, C/N measurement, voltmeter function, spectrum analysis and data logging. Also it is easy for user to obtain a report of test data via PC or printer through toolbox software.
