Filter Results By:
Products
Applications
Manufacturers
- CAMI Research Inc.
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large library to match your connector. Then touch the tester probe to the connector pins one-by-one to automatically detect and assign a test point to each pin. A synthetic voice reads probed pins as you touch them so you don’t need to take your eyes off the connector you’re probing. Finally, enter pin labels of your choice if you wish to override the standard designations.
-
product
Deep And Sloped Pan Fixtures
Line of deep and sloped pan fixtures for general purpose/system non-specific pcb test applications. H+W Test Products manufactures test fixture products for in-circuit, functional and combinational testers for users of automated test systems (ATE) such as Aeroflex, Agilent (HP), Checksum, Factron, Teradyne (GenRad), Test Research (TRI) and Testronics.
-
product
Vacuum Test Fixtures
Vacuum fixture kits for Pylon block fixture, Teradyne, Keysight, Digitaltest,Seica, Cobham (Aeroflex), ATX exchangeable system.
-
product
In-Line / Board Handler
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
product
Supported Test Systems
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
product
Wireless Test Fixtures
At Forwessun, we have vast experience in designing and delivering wireless in-circuit test (ICT) fixtures. We have experience in providing fixtures tailored to the unique needs of various different industries. While our primary customer focus has been on full and half-bank fixtures for the HP3070 system, we offer bespoke solutions for other platforms as well including GenRad, Teradyne, and SPEA systems.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
CAD / BOM Translation Software
ProntoTEST-FIXTURE
In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Materials (BOM) files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is then used by Test Engineers to program their ATE (Agilent/Hewlett Packard "board & board x/y", Teradyne "ipl", Genrad ".ckt"), MDA, and flying probe test equipment and design the "Bed of Nails" test fixtures.
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Single-TAP CFM JTAG Controller for Teradyne ICTs
USB-1149.1/CFM
The USB-1149.1/CFM High-Speed single-TAP boundary-scan controller makes adding JTAG test to Teradyne ICTs a snap. Designed specifically for integration into Teradyne TestStation and GR228x testers, the USB-1149.1/CFM offers a clean, convenient boundary-scan solution.
-
product
Pod/Nest Fixtures
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
product
Functional Fixtures
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
product
Test Fixture
OCP NIC 3.0
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
product
Fixture Kit
MF300
Due to careful selection of materials, use of modern manufacturing techniques, and supplying the kit "flat packed" for end-user assembly, Merifix fixtures kits are inexpensive enough to be used in low-volume production and in engineering labs for programming and debug tasks, where traditional fixtures would be too expensive.
-
product
Test Fixture
N1295A
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
product
Test Fixtures
REINHARDT System- und Messelectronic GmbH
Is a fixed state of a set of objects used as a baseline for running tests. The purpose of a test fixture is to ensure that there is a well known and fixed environment in which tests are run so that results are repeatable.
-
product
Parametric Test Fixture
U2941A
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
Functional Test Fixtures
RNS can build almost any test equipment and automated test machinery. We have delivered soltions for HiPot, LED Test, Leak Test and RF shielded applications for years. We can provide Complete Test Systems, including Test Fixtures, Rack System and even Programming. Our team is committed and has a proven track record of delivering exceptional products independent of scope, so simple- and high-complexity projects are handled with equal care.
-
product
Function Test Fixtures
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
product
PCB Test Fixture Kits And Customized Fixtures
Mirotech manufactures portable benchtop PCB test fixture kits and provides customized test fixture solutions for the electronics industry. Our innovative, streamlined designs are compact in size and feature a linear collapsing system, interchangeable and reusable plate design, top and bottom probing, and are affordably priced. All fixtures are built using high quality hardware and materials and manufactured using the DATRON M8Cube, known for its precision and accuracy. Each of our custom designs are unique to our customer’s particular project requirements. Fixture kits come pre-assembled, and include blank plates ready for you to drill your test pattern.
-
-
product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
