Filter Results By:
Products
Applications
Manufacturers
AC Power Supplies
Supply Alternating Current (AC) electricity to output loads.
- Pickering Interfaces Inc.
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector
40-153-104
The 40/42-153-104 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
PC Controlled Bench Top Power Analyzer
PA2100
The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.
-
product
DC POWER
VARIABLE TRANSFORMER
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
product
AC to DC Programmable Power Sources
CEHCO can supply AC to DC Programmable Power Sources. We offer standard or customized solutions. The ADG-L Series is up to 1000 VDC maximum output. ADG-P Series is up to 2000 VDC maximum output.
-
product
cPCI 6U AC 500W
Hartmann’s cPCI Power Supplies comply with PICMIG and offer a wide range AC input. These supplies are developed and produced with quality and durability in mind, at a price that won’t bankrupt your project. Talk to a Hartmann representative today about your power needs!
-
product
Regenerative Grid Simulator
Chroma 61800
Chroma Systems Solutions, Inc.
Full 4 quadrant, fully regenerative, AC power supply designed for common electrical product testing such as home appliances and industrial electronics that require a programmable input source
-
product
Power Supply, 60 V, 85 A, 5,100 W
N8757A
The Keysight N8757A is a 60 V, 85 A, 5,100 W, single-output power supply in a small 2U package. It offers flexible AC input options, analog / resistance control of output voltage and current, and parallel and series connection of multiple supplies to achieve more output current or voltage.
-
product
Harmonic/Flicker Analyzer for IEC61000-3-2/3/11/12, IEC61000-4/7/15
KHA3000
KHA3000, in addition to the complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*. Furthermore, the KHA series is compliant with two measurement technique standards, the existing and the latest versions, so you can simply select to take measurements for the latest standard including interharmonics and for the conventional integral multiple harmonics without using any other device. In addition to the real-time display that can be used like an oscilloscope and FFT analyzer, the unit offers the real-time judgment of compliance with standards. Using this unit alone, you can judge test results and prepare result reports without the use of a PC. On top of that, you can easily set up a test system by combining KHA3000 with an AC power supply (PCR-LA Series) and a line impedance network (LIN40MA-PCR-L).
-
product
60kw off grid power inverter 110/220V split-phase output converter
SDP-60KW
Zhejiang Sandi Electric Co., Ltd
Our SDP series Off Grid Pure sine wave inverter is one of the most advanced DC to AC conversion products in the world, it is suitable use for areas without electricity, vehicles, ships, solar energy, wind turbine and other renewable energy systems and etc, can supply power and provide guarantee effectively for the areas with traffic inconveniences, in the mountains, pastoral, border, island and other areas without electricity.
-
product
Portable AC/DC Power Supply
UPS S3
The Vanguard UPS S3 is an AC/DC adjustable output power supply designed to operate substation circuit breakers. The UPS S3’s AC and DC voltage sources can supply up to 10 Amperes during the circuit breaker coil energization and circuit breaker charging motor operation. Powered by a single phase 90-120 Vac voltage source, the UPS S3 provides an isolated adjustable AC/DC voltage source. Output voltages are variable via the front panel control knob.
-
product
Mini Redundant Power Supply; ATX 500W (AC Inlet In Front )
PS501-HRP
*Input Range: 100~ 240VAC Full Range*Output Voltage:**+5V, 25A**+3.3V, 25A**+12V, 41A**-12V, 0.8A**-5Vsb, 3.5A*MTBF(hours): AT 25°C 100,000h*Safety: CB, CCC, UL, TUV, CE, FCC*Dimensions: 185 x 150 x 86 mm*Compatible with Axiomtek products: AX6156LE/AX61220
-
product
Bidirectional AC Source / Sink With Regenerative Power Supply
EAC-4Q-KS
*Single system from 15 kVA to 90 kVA and in parallel up to 500 kVA*Seamless transition between source and sink mode*Output: AC, DC, AC + DC*Output up to 2000 Hz (-HF option)*Add single-phase output (option -1P)*Up to 750 V LN output*Modular construction
-
product
DC Filter Inductors
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
product
High-performance multifunctional AC Power Supplies (CV/CF)
PCR-LE Series
The PCR-LE Series is a new line of advanced multifunctional AC power supply that has been developed from our PCR-L/LA Series (linear amplifier type). The PCR-LE Series provides high reliability and can be applied to various applications, by taking advantage of the features that can control broadband waveform freely. Moreover, the PCR-LE Series can be configured as a core device of a test system combined with E-loads and Power Analyzers for “Grid Connection Testing” in regard to dispersed power generation, such as Solar Power, Wind Power, Fuel Cell, and Gas Engine referred to as “New Energy Field”. With various options, the low frequency immunity test and various power enviroment tests are supported. The options for parallel operation and three-phase operation enable you to expand a single-phase system up-to 27kVA, single-phase three wires up-to 54kVA, and a three-phase system up to 81kVA. The system can be applied to a large-scale EMC site for testing of industrial high-capacity air conditioners.
-
product
500-Watt AC/DC Power Supply
56TS1
NAI’s 56TS1 is a 500 Watt AC/DC Power Supply that accepts a 3Ø AC input or a +270 VDC input. This COTS unit provides full-power output power at a baseplate temperature of +85° C.
-
product
PXI-2565, 16-Channel, 7 A, SPST PXI Relay Module
777754-01
16-Channel, 7 A, SPST PXI Relay Module—The PXI‑2565 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It delivers high-current switching of DC power supplies, AC line power, and AC/DC current sources. The PXI‑2565 is fully software programmable and supports multiple instrument synchronization.
-
product
Differential Voltage Probes
DP150/DP200pro
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
product
Three-Phase Transformer Demagnetizer
DEM60C
After a DC current test, such as winding resistance measurement, the magnetic core of a power or instrument transformer may be magnetized (remnant magnetism). It can cause various problems such as wrong diagnostics, inaccurate measurements on a transformer, inrush current at the start-up of a power transformer, or incorrect operation of protective relays due to magnetized CT cores. The best way to eliminate this source of potential problems is to use demagnetizer on the power or instrument transformer.The DEM60C is a fully automatic test instrument which performs three-phase transformer demagnetization. Transformer magnetic core demagnetization requires the application of AC current with magnitude decreasing to zero. DEM60C provides this AC current by internally changing the polarity of a controlled DC current. During the demagnetization process, the instrument supplies the current at decreasing magnitude for each step, following a proprietary algorithm. It can demagnetize single-phase and three-phase power transformers.The instrument can be connected to all three phases of a power transformer to be demagnetized, on either the primary or the secondary side. If a user selects specific vector diagrams for different types of transformers, DEM60C will run a specific demagnetization procedure for each transformer type (i.e., single phase, delta, wye/star, zig-zag.) without switching the test leads.DEM60C enables safe and efficient power transformer demagnetization. The instrument automatically regulates the injection of current and discharging energy from the inductance. During and after the operation, an intrinsically safe discharge circuit with an indicator rapidly dissipates the stored magnetic energy. The discharging circuit is independent of the power supply, which improves its reliability in case of loss of power.Test currents of up to 60 A DC enable efficient demagnetization of even the largest power transformers. Using a DV Win software, it is possible to control DEM60C externally.
-
product
AC Power Supply
AC Power Supply, Shuangyi AC power products are mainly linear AC power sources: TFC-1000 series
-
product
Portable Moisture in Oil and Dewpoint Analyzer
DOMINO USS
The Doble DOMINO USS (Ultimate Sampling System) gives you a fast, efficient way to measure water content in oil and/or the dewpoint of a gas.The DOMINO USS is a portable system that connects quickly and easily to transformer valves or other oil-filled electric devices.Operating on AC power supply or with its rechargeable battery, you will have accurate readings in six minutes or less.The DOMINO USS is customizable to your testing requirements, coming with either a moisture-in-oil sensor, a moisture-in-gas (dewpoint) sensor, or both.
-
product
Small Engine Dynamometers
Toroidal-flow water-brake absorber (with 5" high-RPM rotor), electronic torque-arm transducer, engine load control, DYNOmite handheld data-acquisition computer, AC power supply, stainless-braided hoses, magnetic RPM sensor, data wiring harness, and protective carrying case.
-
product
Power Supply, 100 V, 50 A, 5000 W
N8759A
The Keysight N8759A power supply is a single output power supply in a small 2U package that offers essential features to fit your budget. The N8759A power cable offers flexible AC input options, analog / resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage.
-
product
High Performance Programmable AC Power Supply
IT-M7700 Series
ITECH newly-launched IT-M7700 High Performance Programmable AC Power Supply combines intelligence and flexibility, breaks through the huge defects of the traditional AC power source, reduces the size to only 1⁄2 1U, maximizes space utilization. Built-in power meter and arbitrary waveform generator make it convenient to simulate various arbitrary waveform outputs. IT-M7700 is designed with advanced technologies of programmable AC and DC power supplies, and can be widely used in multiple fields such as power energy products, home appliances, industrial electronics, avionics, military and IEC standards testing.
-
-
product
Power Supply
44216
This extremely efficient power supply converts 100~240 AC volts into 17 amps of continuous 13.8 volt DC power, making it compatible with a wide variety of DC chargers.
-
product
AC Reference Generators
SR21
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
product
Benchtop Rubidium Frequency Standard
FS725
Stanford Research Systems, Inc.
The FS725 integrates a rubidium oscillator (SRS model PRS10), a low-noise AC power supply, and distribution amplifiers in a compact, half-width 2U chassis.
-
product
Power Supplies
Reliable power supplies enable data acquisition systems to continuously acquire and process data. Because our components use minimal power, many of our systems can be run using sealed rechargeable or alkaline batteries. Systems that require more power are often supplemented with external rechargeable batteries, regulators, ac transformers, or solar panels.
-
product
AC Power Sources
Chroma Systems Solutions, Inc.
AC Power Supplies designed to satisfy both automated test system and laboratory benchtop requirements.
-
product
Industrial Mini-Redundant AC Power Supply, 460W
APS-946XAR-EPS12
- Power (typical): 460W- Current Type: EPS12- AC Voltage Input Range: 110 - 220 VAC (±10%)- Dimensions: 185 x 150 x 86 (mm)
