Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 3A Power MUX BRIC, 8-Channel, 12-Pole
40-571-302
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Load Switches
Analog Devices load switches provide a highly integrated solution for switching voltage rails on in a controlled manner via an internal, high-side switch. This portfolio features overcurrent and overtemperature protection and supports currents up to 3 A. They provide a very low pass element RDSON to reduce power losses. The combination of the functionality and integration levels of ADI load switches make them extremely well-suited to inrush control applications for pluggable optical modules, line side pluggable interfaces protection, power plane switching, and power rail sequencing applications.
-
product
USB Programmable SPDT and SP4T Solid State RF and Microwave Switches
LSW Series
The Lab Brick LSW Series RF and Microwave Switch product family offers reliable, high isolation and low cost solid state switch products in both single pole double throw and single pole four throw configurations. These units require connection to a USB port for control and power. No additional DC supply voltage is required. Lab Brick RF and Microwave Switches are easily controlled and programmed directly from the included GUI and through the external control inputs. Lab Brick Switch API DLL and LabVIEW compatible drivers are also available for custom programming applications.
-
product
3U VPX SDR Module
VPX3-ZU1-SDR
Sundance Multiprocessor Technology Ltd.
The VPX-ZU1-SDR from PanaTeQ is a 3U OpenVPX module based on a Xilinx Zynq Ultrascale+ MPSoC ZU6EG/ZU9EG/ZU15EG using JESD204B interface to an Analog Devices AD9371 or AD9375 Wideband RF Transceiver. Available in Air Cooled or Conduction Cooled version (see picture), this module offers incredible capabilities for the developers looking for ruggedized Software Defined Radio applications and targeting the defence/aerospace market. The module can work as stand-alone module or can be the SBC of the VPX system using the power effecient Quad-Core ARM Cortex A53 SoC and the on-board PCIe Gen2 Switch (worldwide unique feature)
-
product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors, With Interlock
42-153-002-HI
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
1000W Ferroresonant Power Supply
Series PRR
Kepco's PRR are 1000 Watt rack mounted laboratory systems power supplies that offer the low cost and very high dependability of ferroresonant voltage stabilization.The ferroresonant stabilizing technique provides extraordinary isolation from a wide variety of source noise. It is inherently short-circuit proof and cannot expose delicate loads to overvoltage hazards. Hence no crowbar, fuses, or bounding circuits are needed. Ferroresonant power supplies use no noise-producing switches or oscillators. Voltage setting is independent of delicate control settings or diode references and requires no comparators, references, or limiters. Efficiency is 70-80%.
-
product
Powered VXS Crates
6U VXS 6021
The WIENER VXS 6023 crate series adds high performance Switch Fabrics according to VITA 41 specification to VME based systems. Designed primarily for high speed applications in data acquisition, as well as military / aerospace test and instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
product
Pocket Type Digital Multimeter (CE)
MCD-107
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size and light weight.*Easy operation with rotary switch.*4000count full scale with auto-ranging.*Data Hold and Auto Power Off Function.
-
product
MultiTracker
PK-108/108A
The Multitracker provides the most powerful combination of a high power Net toner, cable and network testers in one unit. It generates 2 selectable net tones with the capability to quickly locate and identify active network cables connected at HUB, Switch or Router, and live phone line systems. It also features a pin-by-pin cable testing with an auto scan and step modes for checking detail VDV (voice, data and video) cables pin-out configuration. Network test includes detecting PoE, Ethernet and Telephone services.
-
product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
product
SPDT T/R
Analog Devices provides a range of low cost split path, double throw (SPDT) switches for use in transmit-receive applications that require very low distortion at high incident power levels. Our devices can control from dc to 4 GHz and they are well suited to cellular infrastructure.
-
product
PXI/PXIe Power Relay Module, 5xSPST, 30 Amp
42-166-002
The 40/42-166-002 is a PXI/PXIe high density power relay module with 5xSPST switches rated at 30A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
product
Dual Channel Conductivity-Resistivity Controller
8860
The Signet 8860 Dual Channel Conductivity/Resistivity Controller is a two-channel input device equipped with three scaleable 4 to 20 mA outputs and four programmable relays. A selector switch activates two open collector outputs in place of two of the relays for extraordinary output versatility. Dual input and advanced control capability, including percent rejection, difference and ratio calculations, together with Signet Conductivity Sensors, form the perfect measurement and control system for water treatment applications and more. Two versions are available: once accepts AC line-voltage, the other low voltage DC for power. The four-button keypad arrangement with intuitive software design is user-friendly, and the NEMA 4X/IP65 front panel with self-healing window in a 1/4 DIN package for easy panel installation.
-
product
Single Channel Signal Conditioner
SAM-3
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
product
PXI SPST Power Relay: 20-ch, 5A, 300W
M9135A
The M9135A is a general purpose switch with 20 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module is ideal for switching heavy loads or power supplies including voltages mains or DC current. The heavy-duty armature relays are rated for up to 5A and 300W, enough for inductive or capacitive loads. Choose from the heavy-duty power connector or an unterminated power cable.
-
product
Intelligent Power Switches
ST offers a series of intelligent power switches (IPS) for high-side and low-side configurations. These devices integrate the control section (logic interface, drivers, diagnostic and protection features) and the power stage on the same chip, with benefits in terms of compactness, increased system reliability and cost effectiveness.
-
product
Linear Accelerometer Switch
Columbia Research Laboratories
Columbia Research Labs Accelerometer Switch is designed to interface with electrical or mechanical systems to control, safeguard against, or warn of undesirable variations in DC and low frequency acceleration. This sensor is available with a selectable switch point, a single or Bi-polar switch, and a choice of input power.
-
product
PXI/PXIe Power Relay Module, 5xSPST, 30 Amp
40-166-002
The 40/42-166-002 is a PXI/PXIe high density power relay module with 5xSPST switches rated at 30A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
product
12-1000V AC Adjustable Non-Contact Voltage Tester
5220A
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from12V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
product
Belt-Pack Transmitter
LMb
The LMb transmitter can be configured to operate as a "one touch" device with a single power on/off switch on the top panel, or with full access to all operational parameters using the side panel membrane switches and LCD interface. The top panel switch can also be configured to provide a mute or talkback function.
-
product
Chassis - up to 8 8x1 Modules, 16 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's & 2x2 Modules in Any Combination or Configuration for up to 64 Relay Drives
CXM/64-MF
These Chassis controls up to 8 8x1 modules, 16 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 64 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
product
Single Mode Low Loss All Optical Switch From 8x8 To 192x192 Ports
SERIES 6000
The Polatis Series 6000 Network Optical Switch is a high-performance, fully non-blocking all-optical matrix switch available in sizes from 8x8 up to 192x192. It is designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds. With support of Software-Defined Networks (SDNs) via an embedded NETCONF and RESTCONF control interfaces, the Series 6000 enables extremely low latency for time-critical traffic required for new virtual cloud services in hybrid packet-optical data centers. The Series 6000 is based on Polatis’ patented DirectLight® optical switching technology that has been proven in the most challenging data center, telecom and defense applications and is also used by major network equipment manufacturers to automate testing of optical components and subsystems.
-
product
POWER PROBE III WITH CLAM SHELL - GREEN
PP3CSGRN
*Power Probe 3 is a digital multimeter that provides diagnostic power with the flip of a switch*Determine if motors, lights, fans, relays and circuits are operational on and off the vehicle by applying battery power or ground through the tool*Easy-to-read dual polarity indicators feature a red (+) symbol to indicate positive voltage and a green (-) symbol to indicate ground
-
product
Fail Safe Waveguide Switches
Waveguide switches enable very rapid switching between two RF channels. Fail Safe Waveguide Switches return to the de-energized position when the power is disconnected and requires a small holding current in the energized position. All models have low VSWR and high power handling capacity. They withstand the full power rating of the waveguide and most models can be pressurized to 0.2 MPa (2 ATO) for high peak power applications.
-
product
PXI/PXIe Power Relay Module, 24xSPDT, 5 Amp, 50-Pin SGMC Connectors
42-158-002
The 40/42-158-002 is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
product
Micro Ohmmeter
HTHL-100B / 382
Wuhan Huatian Electric Power Automation Co., Ltd.
Special equipment for field high voltage switch maintenance and high voltage switch circuit resistance test in power supply department.
-
product
100-600V AC Non-Contact Electric Voltage Detector With Buzzer
1969
Peaceful Thriving Enterprise Co Ltd
*With cUL and RoHS Approval.*Check voltage on 100-600V AC.*Two LR44, 1.5V batteries which is included.*Audible and visual indication for easy operation.*Four-section power and sensitivity switch (H, L, M and off).*Locates breaks along live, insulated wires and power cords.
-
product
3 Wire (Digital) Earth Resistance Tester
ST-1520
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Auto power off function.● The timer operates automatically for about three to five minutes when the "PUSH BUTTON SWITCH" and "TIMER ON BUTTON" are pressed together. This will keep test "ON" for the duration of the timer.● Timer for test function (count 3-5 minutes).● Battery operated.● Data hold function.● Small and light weight.● Calibration performed with supplied test leads.
-
product
RF Front-End ICs
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
product
General Purpose Functional Test Systems
Keysight Technologies’ TS-5000 Family of Electronics Functional Test Systems offers a wealth of choices in general purpose instruments, power supplies, switch loading and DIO capabilities in a multiple rack heights, seamlessly connected with open architecture software Test Exec SL, all immaculately assembled and thoroughly tested so you don’t have to.
