Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCI-1564
32 bit, 33 MHz, PCI interfaceInput channels32 isolated digital input channels, 24 V, incl. 16 interruptible and 3 fast counter inputsInput channels organised in 4 groups of 8 channels, each group has its own ground lineVoltage reversal protectionAll inputs are filteredOutput channels32 isolated digital output channels, 10 to 36 VOutput current per channel 500 mAWatchdog for resetting the outputs to "0"After power/ON the outputs are reset to ì0îShort-circuit current for 16 outputs ~ 3 AShort-circuit current for 32 outputs ~ 6 AShort-circuit current per output ~1.5 AElectronic fuseOvertemperature and overvoltage protection24 V power outputs with protection diodes and filtersSpecial output capacitors minimise electromagnetic emissionsExternal 24 V supply screened through a protection circuitryShutdown logic when the external supply voltage drops unter 5 V
-
product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
product
Mainframe or -E Expansion Chassis - Control up to 16 Modules with up to 8 Relays per Module
LXA/128-MF
These Chassis control up to 16 modules with up to 8 relays per module. A large variety of different switch modules are available to build almost any configuration. Modules are available to build matrix or mux configurations or discrete relay modules. Input detection modules, output driver modules and proto board modules allow custom systems for almost any application. LEDs on the front panel show switch and power status. A thumbwheel manual control is optional.
-
product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width- Universal V(I/O) decided by backplane- Comprehensive EMC shielding
-
product
FMC Add-On Cards
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
product
FPGA Processing Board
VP880 / VP881
The VP880 / VP881 is a high-performance FPGA processing board featuring Xilinx® Ultrascale™ and Zynq® Ultrascale+™ technology. It is designed for the most demanding, mission critical military/defense applications such as electronic warfare / DRFM, radar/sonar image processing, satellite communications systems, multichannel digital transmission/reception and advanced digital beamforming.
-
product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
product
Digital Output Board
VME-2128A
VME-2128A 128-bit High-Voltage Digital Output Board with Built-in-Test
-
product
Analog-to-Digital Converter Board
VME-3125A
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
product
Extreme Rugged PC/104-Plus Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM2-BT2
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
Printed Circuit Board
RISER-PPM-1
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
Digital Input Board
VME-1129
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
product
PCI/104-Express Type 1 Single Board Computer with 6th Gen. Intel® Core™ Processor (formerly codenamed Skylake)
CMx-SLx
The CMx-SLx is a PCI/104-Express Type 1 Single Board Computer (SBC) featuring the 64-bit 6th Gen. Intel® Core™ i3 processor (formerly "Skylake-H"), supported by the Intel® CM236 Chipset. The CMx-SLx is specifically designed for customers who need high-level processing and graphics performance in a long product life solution. The CMx-SLx Intel processor supports Intel Hyper-Threading Technology (i3-6102E = 2 cores, 4 threads) and 8 GB of soldered ECC DDR4 memory at 1866/2133 to achieve optimum overall performance.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
Extreme Rugged PC/104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM1-BT1
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
product
Motion Control Terminal Board For Panasonic Minas A Servo
DIN-814PA
- Motion control terminal board with 100-pin SCSI -II cable- On-board connector type: 100-pin SCSI-II female- Suitable for Panasonic Minas A servo- Shipped with 1-meter ACL-10250 cable- Available for PCI-8134, PCI-8164 and PCI-8158- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)
-
product
3U OpenVPX Power PC SBC
68PPC2
NAI’s 68PPC2 is a 3U OpenVPX, NXP® , QorIQ® T2080 quad-core processor, PowerPC-based, Single Board Computer (SBC) that can be configured with up to two intelligent function modules. Ideally suited for rugged defense, commercial aerospace, and industrial applications, the 68PPC2 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
product
Digital Output Board
VME-2533
VME-2533 32-bit Differential Digital Output Board. VMEbus specification compatible double height form factor.
-
product
Quad QSFP28/QSFP+ FMC+ Module
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
- Suitable for Mitsubishi J2 super servo- On-board connector type: 100-pin SCSI-II female- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
product
Terminal Board For General Purpose With 100-Pin SCSI-II Connector
DIN-814-GP
- Available for PCI-8134, PCI-8164, PCI-8154, PCI-8158 and PXI-8164- Supports Specific Servos by Cable Selecting- On-board Connector Type: 100-pin SCSI-II- Dimensions: 146 mm x 85 mm x 44 mm (W x L x H)
-
product
3.5" Single Board Computer With Intel® Core™ Ultra Processors
SBC35-MTL
ADLINK SBC35-MTL, a compact 3.5" Single Board Computer equipped with Intel® Core™ Ultra Processors for efficient, high-performance computing. It features an integrated NPU to boost AI processing capabilities and includes a reserved MIPI-CSI signal pathway for easy camera integration, making it ideal for real-time and vision-based applications. The SBC35-MTL is designed to meet the needs of modern embedded systems, delivering cutting-edge performance in a compact form factor
-
product
3.5" Single Board Computer With Intel® N97 Processor
SBC35-ALN
SBC35-ALN, powered by Intel® N97 Processor, is exceptionally well-suited for a wide range of applications, specifically tailored for EV Chargers. This 3.5-inch Single Board Computer (SBC) from Intel's 13th generation excels in superior performance, power efficiency, and compatibility with cutting-edge technologies.
-
product
Printed Circuit Board
RISER-PCM-1
WINSYSTEMS’ RISER-PCM-1 boards are designed to provide extra space in a PC/104 stack. They are printed circuit boards (PCBs) with PC/104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
COM Express Type 10 Reference Carrier Board
miniBASE-10R
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
