Filter Results By:
Products
Applications
Manufacturers
Band-pass Filters
Refine signal, allowing transmission of only frequencies within a specified, continuous frequency band, while predictably attenuating frequencies above and below the continuous band.
- Frequency Devices Inc.
product
Low-Pass Filters
Is a filter that passes signals with a frequency lower than a selected cutoff frequency and attenuates signals with frequencies higher than the cutoff frequency. The exact frequency response of the filter depends on the filter design.
-
product
Tunable Edge Filters
Tunable edge filter is a customized product. It usually belongs to 2-port optical tunable filter product platform. Instead of using narrow bandpass filter in the 2-port tunable optical filter, the tunable edge filter utilizes a low-pass or long-pass interference filter. By changing the incident angle of the light beam, the cut-off wavelength will be tuned. Standard Tunable edge filters support C-band or L-band wavelength range.
-
product
Miller 400A
44500
Rugged, lightweight case - safe to use on wet ground. Weatherproof, even with lid removed - IP67 rating for dust and water intrusion. Convenient case lid removal for ease of movement, with test leads attached, to new measurement locations. Resistance measurement range from 0.01Ω to 1.1MΩ . Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 97Hz (the unit’s operating frequency). Runs on a set of C-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source
-
product
Reconfigurable Filter Bank
BSC have independently developed a fully reconfigurable adaptive filter solution, designed for fast & seamless switching into any of 256 filter states across the 2-18 GHz range. Ideally suited to EW front-end preselection or protection, any combination of bandpass and bandstop states can be selected INTRODUCTION. Each 2 GHz channel can be switched in (bandpass) and out (bandstop) of the signal path with a switching time of less than 100 ns. DC power and 8-bit TTL control is supplied through a standard 15-pin MDM connector. In the crowded spectrum of the future, front-end flexibility is of increasing importance. Not limited to 2-18 GHz or equal channel widths, the same core architecture may be used in more specific bands, for example at VHF/UHF frequencies. This makes the system equally as suited to EW as it is to Mil Comms applications, where sampling sensitivity or frequency-agile protocols respectively are key to system function.
-
product
Passive Components
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
-
product
Narrow Band Filters (Single Octave)
MINI-SMT® Series
The new MINI-SMT™ tunable filter advances our popular MINI-POLE® Series by providing Surface Mount (SMT) capability along with the field proven RF power handling, low distortion and exceptional selectivity performance of our MINI-POLE® filters. MINI-SMT™ bandpass options are available from 700 MHz to 3 GHz.
-
product
Wavelength Meter
S-107
Wavelength meter slot module of FOTS system offers two main functions of an accurate wavelength meter and a precise tunable band-pass filter. This accurate instrument, which is based on an internal tunable filter, acts as an optical spectrum analyzer or a wavelength meter as well as a low insertion loss tunable filter. The built-in tunable filter of the module is precisely tuned in C-band and L-band optical communication window by using both electronic and optical controlling methods. User can choose the function of this module depending on his or her applications.
-
product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
Broadcast Filters VHF TV
RFS bandpass filters are primarily used as part of multi-channel combiner facilities but can also be used to eliminate spurious emissions and increase isolation between co-sited services.
-
product
Optical Filter Sets
Our filter sets support a great range of fluorophores for microscopes and imaging systems. Patented design techniques drive some of the most spectrally sophisticated optical filters on the market. High transmission, steep edges, precise spectral edge placement, and optimized blocking combine for more reliable measurements. A wide selection of individual bandpass filters and dichroic beam-splitters support unique applications, and world-class manufacturing and cutting-edge metrology ensure consistent performance that always meets specifications.
-
product
Tunable Filters from Stock
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning desired signals while rejecting interfering signals. Mechanically-tuned, high Q cavity filters typically allow center frequency to be tuned over at least one octave.
-
product
Tunable Filters
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422 or BCD.
-
product
Filter Building Blocks
Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) filter building blocks. These devices were designed to simplify the implementation of band-pass, high-pass, low-pass, notch, or all-pass filters using classical filter realizations (such as Butterworth, Cauer, Bessel, and Chebyshev).
-
product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
product
Diplexers
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
product
Band Reject (Notch) Filter Components
precision band-pass and band reject (notch) active filters that provide high performance in a compact 32-pin DIP package, with a broad range of fixed center frequencies (fo) from 1 Hz to 100 kHz. Each filter type features a neartheoretical amplitude/phase response along with lowoutput voltage noise enabling these filters to achievea 10,000:1 or better dynamic signal range.
-
product
Broadcast Filters FM
RFS bandpass filters are primarily used as part of multi-channel combiner facilities but can also be used to eliminate spurious emissions and increase isolation between co-sited services.
-
product
RX Pre-Amplifier System
RAM-34
The RAM-34 is a complete pre-amplifier system designed primarily for the low bands 160M thru 40M. It has inputs for four receive antennas and internal 3-pole bandpass filters for 160M, 80M and 40M. In addition to the pre-amplifier, it has a step attenuator that togetherwith the amplifier stage provides gains from -20 dB to +20 dB in 5 dB steps. This allows equalizing the signal levels between the antenna inputs. Gain settings are memorized for each antenna on each band. Different types of receive antennas have different signal levels and the gain memories eliminate the need to adjust the receiver or pre-amplifier when switching between the antennas.
-
product
Precision Low-Loss Multiplexers
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
-
product
Bandpass Filters
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
product
Low Pass and Bandpass SMA Coaxial Filters
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
product
Bandpass Filters
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
product
0.5-18GHz Switch Multiplexer
SA004
Teledyne Defence & Space’s (TDS) patented designs have produced many different types of filters incorporating switches. These are all generally wideband for Electronic Warfare applications and enable the control of the frequency spectrum into any given system. These units, also known as Switch Multiplexers, are configured with a single or multiple inputs to single or multiple filtered outputs.As an example, the SA002 features 8 channels switchable over the frequency range 2-18 GHz while the SA004 offers 17 channels over the 0.5-18GHz bandwidth. Each provides the user with a fast, flexible, filter network capable of providing different band-pass or band-stop responses on a pulse-by-pulse basis in dense signal environments.
-
product
Miller 400D
44550
No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)
-
product
2-18GHz Switch Multiplexer
SA002
Teledyne Defence & Space’s (TDS) patented designs have produced many different types of filters incorporating switches. These are all generally wideband for Electronic Warfare applications and enable the control of the frequency spectrum into any given system. These units, also known as Switch Multiplexers, are configured with a single or multiple inputs to single or multiple filtered outputs.As an example, the SA002 features 8 channels switchable over the frequency range 2-18 GHz while the SA004 offers 17 channels over the 0.5-18GHz bandwidth. Each provides the user with a fast, flexible, filter network capable of providing different band-pass or band-stop responses on a pulse-by-pulse basis in dense signal environments.
-
product
Spectrum Marker Generator
NSG-2
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
product
Passive Component Integration
Integrate passive optical components of your choice such as WDM couplers, splitters, band-pass filters, PM beamsplitters and circulators. PXIe and benchtop models support SMF, MMF and PMF.
-
product
Pre-Amplifiers
MPR, MDA series
MPR, MDR series provides low noise, high gain and wideband to improve dynamic range for emission testing. We also offer customized model for variable requirments.. Example 30M-1000MHz with band-pass filter Amprifier unit for connecting antenna directly
-
product
Passive Component Integration - PXIe
Passive Series
The Passive PXIe module is a highly customizable PXIe module that can integrate the passive components of your choice.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
product
High Frequency Tunable Bandpass Filters
CTB Series
Tunable Ranges Up To 8 GHz. Bandwidths 1% to 5% of Tuned Center Frequency. Digital Control Offered in Various Inputs, including GPIB (standard), RS-232, RS-422, and USB. Custom Interfaces Available.
-
product
LTE/WiFi Test Box - Adjustable Bandwidth Tunable (700MHz - 6000MHz)
K&L has developed and is now shipping an LTE/WiFi testing solution digitally-controlled filtering system that can tune a bandpass filter anywhere in the 700 MHz to 6000 MHz range with continuously adjustable bandwidth. View latest video to see in operation.
