Filter Results By:
Products
Applications
Manufacturers
- Grund Technical Solutions, Inc.
product
Manual Test Solution
Titan
Grund Technical Solutions, Inc.
Titan is an easy to use, low cost Human Body Model (HBM) or Machine Model (MM) manual test solution. It can be used for design, engineering, and characterization of your devices. Ranging from 50 V to 16,000 V the Titan will have the largest voltage range of any HBM tester.
-
product
200/400 MHz Data Converter Test Solution
ATX7006A
The ATX7006A is a fully integrated solution for testing ADCs, DACs and other Analog functions. It combines very high accuracy, low noise and fast sampling with an exceptional ease of use. Traditionally data converters are tested using a whole stack of bench instruments, filters, switch matrices and user made software. Many engineering hours are needed to get reliable results. The ATX7006A is a single instrument for all your data converter testing and test methods.
-
product
Fatigue Testing And Certification
Fatigue engineering is subject to uncertainty, and data from well executed tests are used to validate conclusions made by analysis and to provide a basis for structural certification. Our staff have extensive experience in testing materials and components under slowly varying, static loads, and under rapidly varying cyclic loads. Tests under static loads are used to assess material properties or to assess the load-deformation behavior of structural components. Tests under cyclic loads provide time to crack initiation, time to failure, or measurements of crack growth over time. We have extensive experience in measuring fatigue crack growth behavior in metallic materials. Past programs have measured crack growth with microscopy and photogrammetry at the surface, cracked area with direct current potential drop, and through-thickness crack profiles with quantitative fractography. By assessing crack growth with a variety of experimental methods, we enable robust analysis validation for cases of complex cracking. Our capabilities in fatigue engineering allow for careful design of a fatigue test program. Whether the tests use constant amplitude loading or an irregular loading spectrum, we specialize in engineering the test that meet your needs. Much of our experience is in non-standard test programs, which require engineering to optimize the test setup. Few others match our capability and experience in fatigue test engineering.
-
product
Embedded Engineering Solutions
Our engineering solutions support the development of safety-critical embedded systems. We support systems, hardware and software engineering, software V&V including multicore timing analysis, the development of efficient automated test environments, and develop custom tools to meet verification needs.
-
product
Electrophotography
Quality Engineering Associates Inc.
Drawing on years of applications experience, QEA has developed a comprehensive line of tools for evaluating EP printer components and sub-systems. This unique family of test systems embodies innovative engineering solutions and a fundamental understanding of the physics of EP processes to give you “must-have” tools for high-speed printer R&D and quality control. These non-contact, non-destructive tools emulate the EP printing process and deliver quantitative data you can rely on. QEA tools are ideal for:
-
product
Customized Thermal Management Test Bench Solutions
Our IPEtec test bench engineering business unit plans and provides customized test bench solutions for the development and validation of automotive AC components. We offer a full range of test benches and media-supply modules for the automotive developer’s thermal management needs. Moreover, we support the development of new cooling systems for hybrid power trains, for battery and engine cooling. New hybrid power trains are opening up additional fields of heat-pump technology development aimed at optimizing the energy balance of automotive air conditioning.
-
product
Test Engineering
TestEdge engineers have an average of 17 years of engineering experience in test, packaging, and fixturing. This experience is across a wide spectrum of products, customers, and ATE platforms. We have experience in all of the following:Digital, analog, mixed-signal, RF Test programming servicesRemote test capability Semi-automatic test generation Automatic data collection and reduction High performance test fixturing Format independant vector translation High power testing with liquid cooling
-
product
Test Stand Engineering
m+p international has the expertise, experience and all resources necessary to design and construct custom-made vibration and functional test stands for various industries. You determine the range of services, the time frame and the budget.
-
product
ElectroForce Mechanical Test Instruments
We start with your specific testing needs and combine unique ElectroForce motor technologies with our test applications engineering expertise to create a tailored test solution that meets your testing objectives. After you buy a TA Electroforce product, you become a valued, lifelong customer. Providing exceptional, ongoing support is our commitment to you.
-
product
Build to Print Services
Amfax are a Build to Print manufacturer with the production and quality processes necessary to service the demanding Aerospace, defence and commercial markets, but it is our extensive engineering and manufacturing expertise that really differentiates us. As a leading test system integrator and supplier, we are able to apply this expertise to your Build-to-Print projects.
-
product
Mini Hand Held OTDR
HW-358T
Shanghai Fibretool Technology Co.,Ltd.
As fiber optics plays more and more important role in modern telecommunication and CATV networks, the requirements to the construction, test and maintenance of fiber optics links also become more prominent. Fibretool HW-358T is a unique product mainly designed for construction and maintenance of telecommunication and CATV networks. Fibretool HW-358T can be widely used in engineering construction 、maintenance test and emergency repair of all fiber optics related systems. Comparing with a regular OTDR, Fibretool HW-358T is more compact in size and easier for field use.
-
product
KWH Meter Test Bench
This test bench is widely used in electrical and engineering sector for varied testing applications.
-
product
Test Solutions For OEMs
A partnership with Testek Solutions fits into your business because we do business like youdo business. Our partnerships are built on open communication, process transparency, and trust – trust that is built on our proven engineering design process. We assign a dedicated team consisting of a program manager who will be your single-point-of-contact, an experienced project engineer to design and oversee all engineering on the project, and any supporting engineers and manufacturing team members necessary for every project. Each test stand goes through a series of stage gates including an initial review of requirements, preliminary design review, critical design review, final design and manufacturing review, and a quality review regardless of whether you request these reviews.
-
product
Energizer BLACK Vibration Exciter for Buzz, Squeak & Rattle (BSR) Testing
Energizer BLACK Vibration Exciter
The Energizer BLACK Series is part of a family of extremely quiet vibration exciters. The Series is ideally suited for the support of subjective and objective BSR evaluations according to industry test specifications, such as GMW14011, GM7293TP, BMW PR311-2 or PSA “Specification bruit parasites”, as well as several Hyundai Engineering Standards. With availability in four unique models and sizes, the Energizer Series is expressly designed to support such evaluations, while reducing the risks of measurement uncertainty caused by unwanted vibration exciter noise occurring within the BSR test environment.
-
product
ESD & Latch-Up Test Service
MASER Engineering has automatic test equipment for the most common ESD test pulse models. MIL - JEDEC - ESDA - IEC standards. IC level Human Body Model. IC level Machine Model. IC level Charged Device Model. System level IEC 61000 HBM. AEC-Q100 Field Induced Gate Leakage test. Static Latch-Up test. Dynamic Latch-Up test.
-
product
ATE Development Services
Automated Testing Engineering and Automated Test Equipment (ATE) provide a faster, more efficient way to test your product. With the help of LabVIEW and Modular Instruments, our engineers create test and measurement systems for all areas of product design and manufacturing.Whether you are in early stage R&D prototype testing, and design validation, or providing a solution for quality control and life testing our engineers can work with you to design fully customized automated Test Systems using entirely off-the-shelf products to ensure you deliver quality product on time.
-
product
Services
Besides our product line of perceptual quality testing products, we offer extensive services in the field of QoS testing, where you can immediately benefit from the technology source - the expertise and experience of our developers. This is most often the case for field studies, or during the evaluation of network components, either if the customer's demand for QoS testing is a temporary one, or simly, if no engineering resources are available otherwise. For instance, OPTICOM could provide comprehensive QoS consulting, including not only objective but as well subjective evaluation, like we did during the introduction of a novel digital satellite broadcast service in the U.S. As a major contributor to the ITU standards, OPTICOM can also provide expertise in implemenation and conformance testing of independent implementations. Even if your PESQ implementation works according to specs, you should consider that an independent conformance test seal could be an asset that will leverage the value of your product from a marketing persepective.
-
product
Fixture Design
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
product
RF & Microwave
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and attitude to utilise the latest technologies.An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements. A list of products is given below.
-
product
Proving Units
Designed to suit a range of applications in the electrical contracting power utilities and industrial engineering sectors Seaward proving units are both self-powered and self-testing avoiding the need for a known supply point or bulky test equipment.
-
product
Video Test Generators
802 Series
The Teledyne LeCroy quantumdata 802 series video signal generators support testing for CRTs, flat panels, projectors and TVs including HDTV. The 802 is optimal for testing DTV, digital and analog displays and allows production and engineering users to create the most complex test images. You get the flexibility required to meet a tough production budget with the wide range of outputs the 802 series offers. And a PCMCIA slot makes it easy to copy the configuration of one generator to another.
-
product
Power Analyzer
2105
The model 2105 provides accurate, reliable, & low-cost power measurement that enables engineering, production test, and quality assurance departments determine precise product power consumption from DC and AC power sources.
-
product
Electromagnetic Environmental Effects
EEE
Electromagnetic Environmental Effects Services provides engineering design and test implementation for Electromagnetic Interference and Compatibility (EMI/EMC), along with TEMPEST capabilities certified under the National Security Agency (NSA) TEMPEST Endorsement Program.
-
product
Testing And Design Services
Rhein Tech Laboratories, Inc. (RTL) is a full-service design and compliance engineering test laboratory. We have grown with the industry from general purpose EMC testing into other areas of testing such as Radio (RF testing), Military and Aviation, Industrial, Scientific and Medical, Automotive, Electrical Safety, Shielding Effectiveness, Site Surveys and Radar Cross Section & High Range Resolution measurements.
-
product
EEE Component Testing and Screening Services
DPACI performs 100% screening as well as qualification testing on electronic parts supplied to the high reliability commercial, industrial, space, and U.S. military sectors. We generate software and hardware to test microcircuits, discrete semiconductors, hybrids, PEMS, and other EEE electronic components to exact customer and military specifications. Our engineering experience in electronic parts screening, qualification, and in-house test fixture fabrication allows us to provide value added components in a timely manner.
-
product
Semiconductor Test Software Solutions
The test engineering staff at Test Spectrum has developed hundreds of test software projects on all major ATE platforms for numerous product technologies.Whether you need to optimize a current test platform, convert to a lower cost test platform, or design a brand new program for a cutting edge product within incredible time constraints, the Test Spectrum team will exceed your program expectations with quality products and excellent results.
-
product
Intelligent Digital Multimeter, Calibrated, 3999 Count, Mean Value, Auto, Manual Range, 3.75 Digit
72-7755 CAL
The 72-7755 CAL from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
-
product
Test System
Griffin III
The Griffin III system brings new price/performance efficiency to the Tester-in-a-Head tradition, a concept created and introduced by HILEVEL in 1987. This tester is a superior cost-effective solution for Engineering, Production, and Failure Analysis test applications.
-
product
Test Solutions For Integrators
Beyond being your test equipment expert, Testek can also provide engineering design advice and guidance on building complete test solution facilities. We will work closely with your building contractor to advise on the most optimal layout configuration and to specify all facility resource requirements. For systems that may share resources, we can facilitate resource demand and management, including power management and fluid management. With a central control system, we can provide software logic to monitor these resources and route them appropriately based on demand and priority.
-
-
product
In-Circuit Testing and Test Engineering
GenRad 2287
3560 Hybrid Test NodesWindows InterfaceTotal GenRad 227X Migration Capability20 Mhz Clock, Sync, and Trigger, 5 Mhz data ratesVector Test for VLSI, PLCC’s & ASICSTest Express Vectorless TestingMultiple Chain Boundary ScanAnalog Functional Test Module
