Filter Results By:
Products
Applications
Manufacturers
-
product
Imaging Photometers
Westboro Photonics offers an intelligent selection of imaging photometers. With a wide range of resolutions, an assortment of lenses, flexible software, and cooled systems, our products are unmatched in the marketplace. We provide three series of photometers to satisfy almost any 2D luminance-based measurement need. Applications including Graphics Testing, Beam Pattern Distribution, Flat Panel Displays and Avionics Panel Balancing are handled with ease, thanks to our robust design, extensive calibrations, and flexible, intuitive analysis software.
-
product
Autocompute LCR-Q Meter Sorter
Model 4912 / 4912PR
- Microprocessor based Fully Automatic L, C, R, Q and D measurement- Autoranging with Direct Digital Readout- 4 Terminal Measurement Technique- No Tuning or Balancing- Series or Parallel Equivalent Measurement- Absolute Value and Nominal Value with Percentage Tolerance- Single / Multiple Parameters Check During Component Sorting- Feather Touch Keys with Audio Feedback- Thermal Shut Down for Overheat Protection- Special Mechanism for Fast and Easy Insertion and Removal of Test Component- Low Cost and Portable- Component Sorting on Absolute or Nominal Value Basis with a Percentage Tolerance- Aplab Model 4912PR is Remote Programmable Auto Compute LCR-Q Meter Sorter, Which can be Programmed through GPIB, RS232 or SPIB Interface
-
product
Battery Management Systems Testing
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
product
Machinery Fault & Rotor Dynamics Simulator
MFS-RDS
SpectraQuest’s Machinery Fault & Rotor Dynamics Simulator (MFS-RDS) is an innovative tool to study the dynamic behavior of rotors supported by oil lubricated journal bearings, as well as other common machinery faults, such as balancing and resonance study. An oil pump is provided with the simulator to drive the lubrication fluid. In addition, it provides different bearing clearance selection and controllable lubrication oil pressure for rotor dynamics whirl and whip phenomena.
-
product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
Battery Electronics
CAES Battery Electronics provide autonomous, dissipative, and continuous cell balancing to maximize available battery capacity, and therefore battery cycle life, throughout a mission.
-
product
IntellaView
EdgeSwitch
The IntellaView EdgeSwitch is a high-density 1RU system with 32 ports of 40G / 100G Ethernet capability, while the breakout mode can support up to 128 ports of 10G / 25G. The EdgeSwitch enables efficient traffic aggregation, filtering, load balancing, tunnel management, and port tagging standalone or as part of a larger visibility solution.
-
product
Reference Standards
GF333V2
Beijing GFUVE Electronics Co.,Ltd.
Standard kWh meter is a reference standard with the characteristics of wide-range, multifunction and high-precision. It has accuracy class of 0.02. By adopting techniques of DSP, embedded system and automatic temperature balancing and other compensation, it has not only advantages of light weight, small size, high precision, high performance, powerful function, original interface, ease-to-use, but also work stability.The product can be widely used in fields of electric energy measuring, electric energy laboratories and other relevant industry, not only in laboratories but also at the industrial field.
-
product
Deadweight Testers & Gauges
The most accurate instrument available for the measurement of pressure above a few psig is the Hydraulic Deadweight Gauge. This type of gauge operates on the principle of balancing a known mass against the force exerted by an unknown pressure on a piston of known area. When an exact balance is achieved, the unknown pressure "P" is equal to the mass "M" of the weights divided by the area "A" of the piston, according to the formula "P" = "M" / "A". In us, weights are removed or added from the piston's table, as with a double-pan balance until the piston "floats" without net vertical movement.
-
product
PC Based Rotor Tester
GTS 1000
The PC Based Rotor tester is the most reliable, fast and cost-effective way to detect faults in the Rotors in less than 10 seconds. This Rotor Tester can Test Large sized Rotors of any Size, Length & Weight that can be mounted on a Load balancing machine or a Lathe and rotated at a speed of 600 rpm.
-
product
Alnor Micromanometer
AXD610
The Alnor® Micromanometer AXD610 is an easy to use, handheld digital micromanometer for fast, accurate and reliable pressure measurement. It can also calculate velocity when used with a pitot tube. Ideal applications include HVAC commissioning and troubleshooting, testing and balancing, Pitot tube duct traverses, static pressure measurements and differential pressure measurements.
-
product
Automotive Products
Renesas has invested in key technologies to address the current mega trends within the automotive market such as environment, safety, information, and affordability. This effort has resulted in leadership positions in high-performance power conversions, state-of-the-art precision analog, cell balancing and battery charging ICs, power-efficient Class D audio amplifiers, and highly flexible TFT display controllers.
-
product
Automatic Dielectric Constant Tan Delta And Resistivity
No Balancing and Calculation required to calculate Volume / Surface Resistivityand Dielectric Constant.Complies IEC 60250, IS 4487, Test jig Conform to ASTMD 257Built in Thermal PrinterSerial port RS232 for data downloading.Can be used to check liquid sample with Three Terminal oil cell.Storage 100 Test reports
-
product
Transformer Ratio Meters / TRM-11
TRM-11
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Fully automatic: No manual balancing. Automatic measure transformer group. Automatic calculation of ratio error.
-
product
Instrument Transformer Comparator
PMT20010
Power Measurement Technologies Inc.
The PMT20010 Comparator is an automatically balancing bridge that measures the accuracy of instrumentation potential and current transformers.
-
product
HEV Battery Reconditioner
Battery reconditioning and cell balancing is a well understood process for NiMH batteries. The procedure was initially developed for NiCad batteries decades ago. NuVant Systems has simplified the process to bring electrochemistry to the streets. The EVc unit is a push-one-button-after-wire-up system for small shops to large vehicle operators.
-
product
IEC60065 Socket Torque Balance Tester Torsion Tester
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
product
BMS Tester
MS-159
This equipment used for F/W writing, Calibration and function test. It inspect current, voltage protection mode, consumption current and cell balancing measurement to check the state of BMS and applied to the full inspection and mass production.
-
product
Balancing Software Module
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Balancing of long and disk-shaped rotors in one or two planes*Up to six correction methods (depending on software version)*Automatic operation by rotary speed detection*Display of measuring results as polar graphic and numbers*Very simple installation and operation*User guidance by clear text instructions*Extremely compact - VM-BAL fits into a small carrying case*Versatile instrument at an economic price*Available as kit including all necessary hardware and software: - VM-BAL Kit One for one plane -VM-BAL Kit Two for two planes
-
product
Measuring Solar Fields
ISET Sensor
The solar radiation sensor is characterized by a simple and compact but precise structure. Use in balancing monitoring systems for simple, fast and reliable information about the functioning and solar "energy yield" of a PV plant. For site surveys, monitoring and other fields of survey technology.
-
product
Dynamic Balancing
Balancing machines of the VibroDAQ series are professional sets of tools for measuring vibrations and dynamic balancing of rotating elements in own bearings and on specialized stands.These devices are used in various industries, car workshops, repair services, and departments dealing with maintenance in various types of companies. Our balancers have also been used in scientific institutions and universities as systems for conducting research and training future engineering staff. Our devices have implemented special algorithms for balancing the grinding wheels, allowing for balancing the grinding wheels directly on the grinder.
-
product
Optical Speed Sensors
Allows use in a wide range of hazardous environments in petrochemical, Gas and volatile materials processing industries, ideally suited for Condition Monitoring, Data collectors in balancing applications, these sensors give excellent performance with repeatable results, engineered for easy mounting with the optional Mounting Bracket and Mini Tripod Stand in hand held applications.
-
product
Battery Testing
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
product
Real Scene Lighting
LightSTUDIO
Image Engineering GmbH & Co. KG
Test charts are used to test digital cameras and to perform objective measurements. But there are certain aspects in testing a camera that require a real scene. One of these aspects is the correct white balancing for different types of illuminants. Another aspect might be the determination of the visual loss of detail due to noise reduction or the amount of noise in an image.
-
product
Vibration Analysis and Balancing Tools
PRÜFTECHNIK Condition Monitoring GmbH
Predictive maintenance tools for vibration analysis can help prevent machine failure and avoid costly production downtime. Our vibration analysis tools are used for condition monitoring on rotating equipment to help detect early component wear and damage. Vibration analysis and balancing are integral parts of any condition-based and predictive maintenance program.
-
product
40 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3710
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
Alnor Micromanometer
AXD620
The Alnor® Micromanometer AXD620 is a rugged, compact, comprehensive micromanometer that measures pressure. It can be used with pitot tubes to measure velocity and then calculate flow rates with user–input duct size and shape. Premium features make it ideal for HVAC, environmental safeguards, commissioning, process control and system balancing.
-
product
Check Current Before Working
Radio Ampstik® 2023
The Radio Ampstik uses the same current sensor technology as the original SensorLink Ampstik. It quickly takes accurate current measurements and direction of current flow indication. Knowing source and load direction is essential for power system protection, load balancing, and metering.
-
product
Imaging Colorimeters
Westboro Photonics offers high resolution, high performance imaging colorimeters to meet the needs of manufacturers for several key applications: Computer and cell phone keyboards: automatic measurement, identification and pass/fail analysis for luminance and chromaticity of backlit glyphs and other lit elements. Beam pattern analysis of the luminous intensity distribution of lamps and LEDs. Avionic light plate panel balancing. Transportation, architectural and municipal lighting and signage.
-
product
Information Technology Solutions
*Enterprise Infrastructure Management*Network/Systems Design & Administration*Client/Server Architecture*Classified & Unclassified Systems*System Integration, Engineering, & Analysis*Installation, Maintenance, Support & Upgrade*Network/Server Management & Load Balancing*Government & Commercial Solutions Integration*Operations Management & Maintenance*Strategic Planning*Portfolio Management*Organizational Development*Training & End User Support*Inventory & Asset Management
