Filter Results By:
Products
Applications
Manufacturers
Battery
energy store.
See Also: Lead Acid Battery, AAA Battery, AA Battery, 1.5V Battery, 9V Battery, Button Battery, C Battery, Coin Battery, D Battery, NIckel Cadmium Battery, Lithium ion Battery, SLA Battery, VRLA Battery, NICAD, Battery Test
- Pickering Interfaces Inc.
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
43-752A-903
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Standard 0.49 (13.89) - 2.50 (70.87) Battery Probe
CP-4C
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 60Full Travel (mm): 1.52Recommended Travel (mil): 40Recommended Travel (mm): 1.01Overall Length (mil): 311Overall Length (mm): 7.90Overall Length Remark: Overall length does not include tail.
-
product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-911
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Battery Monitoring System
S5
BTECH's benchmark product designed for a wide variety of applications (UPS/Telco/Switchgear), the S5 can collect data from any battery type including cells with the highest amp hour rating (4000+), and the S5 systems will record all battery parameters.
-
product
Lead Acid Intelligent Battery Tester
612
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
product
Battery Cycler
Rechargeable (secondary) batteries in real-world applications are charged and discharged many times until they reach end of life. Examples of this are batteries used in cell phones, PCs, power tools and automotive applications. After multiple charge/discharge cycles, cell performance starts to degrade. The batteries typically require charging more frequently until eventually they reach end of life and need to be replaced, with the original cells either being scrapped or repurposed.
-
product
Hand-hold Field Intensity Meter
LM870-H
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Trunk-line AC voltage, V/A, C/N and TILT measurable* Automatic over-voltage shut-off protection* AC/DC optional (Ni-H/Li storage battery inside)* Full-digital key-board operation, direct freq. & channel input* Automatic scanning, Automatic channel-filtering, Automatic error-operation amending* All standard channels and subjoin channels pre-set inside* New channel-table setting according to user's special requirement* Character LCD displaying* English/Chinese operation interface* Audio output (speaker set-in)
-
product
MicroLite USB Data Loggers
The family of MicroLite USB data loggers includes six models covering temperature, humidity, current and voltage measurements, providing the ideal solution for a wide range of industrial applications. Combining innovation with simplicity, the MicroLite product line offers cost effective logging, with rich functionality in a compact design, direct USB connection, multi-trip usage, and high measurement accuracy and resolution. Real-time sensor readings with a corresponding time stamp are clearly displayed on the logger’s LCD screen, incorporating alarm thresholds. The logger is designed for low power consumption to extend battery life and reduce the time between battery replacements. The comprehensive MicroLite range allows you to select the device most appropriate to your mission-critical application.
-
product
Supercapacitor Test
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
product
Double Sheet / Splice Inspection
Leuze electronic GmbH + Co. KG
Double-sheet control sensors enable the reliable differentiation between one or more layers of very thin objects made of different materials. This allows, for example, single-layer paper sheets to be reliably pulled in or individual electrodes to be stacked for the production of a battery cell. Different operating principles, based on ultrasonics and capacitive sensors, cover the range of materials for different applications. Sensors for splice inspection detect desired and random splices in paper webs independent of the surface color and material properties.
-
product
Battery Tester
Changzhou Applent Instruments Inc.
Is an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition, namely its capacity for accumulating charge and any possible flaws affecting the battery's performance and security.
-
product
Differential Voltage Probes
DP150/DP200pro
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
product
Regenerative Battery Pack Test System
17040
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
product
PXI BRIC8 FIBO Matrix Dual 140x4 3pin brkout
40-592A-107
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Battery Crush Test Equipment(Horizontal)
Guangdong Bell Experiment Equipment Co.,Ltd
Battery Crush Test Equipment(Horizontal)Application: Battery Module / Battery Pack / Battery System crush test, penetration test.Drive Mode: Electro-hydraulic ServoCrush Tool: Semi-cylinder, hemisphere (According to test standard)
-
product
Standard 1.27 (36.00) - 2.94 (83.35) Battery Probe
CCA-003
Current Rating (Amps): 10Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 78Full Travel (mm): 1.98Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 670Overall Length (mm): 17.02
-
product
Lan-Xi Data Acquisition Hardware
Brüel & Kjær Sound & Vibration A/S
LAN-XI modules can function individually, and can use battery power to create small, rugged, low channel count systems of up to 12 channels. You can attach many different types of front input panels to connect the transducers of your choice. Around each connector is a circular LED that shows the channel's use and health at a glance backed up with an LCD screen. A key feature is the Dyn-X technology, which avoids the need for input ranging by using dual A/D converters to ensure you get the data the first time while achieving an effective dynamic range of over 160 dB.
-
product
Handheld Audio Analyzer
PAA3X
The PAA3X is a highly accurate handheld audio analyzer that gives sound engineers a rich array of sound analysis tools. The system features both 61-band and 31-band real time spectrum analysis, RT60 reverb time measurement, SPL and line meter, internal signal generator, EQ setting program, microphone calibration and speaker phase checking abilities. All functions and menus can be accessed through a central jog dial, leaving your other hand free to adjust audio settings. The large color LCD screen has an adjustable brightness to help you see in a dark or well-lit environments alike. The PAA3X also features a "screen capture" function allowing users to save images of the screen to an SD card in BMP format for later reference. The detachable precision microphone can be placed remotely via the included 5-meter extension cable, offering flexible on-site operation management. With all this plus a built-in rechargeable lithium-ion battery, the PAA3X is a must-have multifunctional tool for all serious audio engineers.
-
product
Battery Module
BAT-200
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Clamp Meters
oltage DC 600V with basic accuracy ±(0.5%+5d)Voltage AC 600V with basic accuracy ±(0.8%+5d)Current AC 400V with basic accuracy ±(2.50%+6d)Slimline Electric Clamp Meter Resistance 20M ohms with basic accuracy ±(1.0%+4d)Continuity buzzer sound at 300 ohmsDiode test current 0.3mA; Open circuit voltage 1.5VAccessories: test leads, carrying case, 2(AAA) 1.5V batteriesSize:8-1/16"L x 2-3/4"W x 1-1/2"HSlimline Electric Clamp Meter Weight: 7oz.2000 LCD display countsDecimal Point ReadingsDisplay with backlightData holdMax holdAuto power offLow battery indication
-
product
LCR Meter
Basic measurement accuracy 0.1% & speed upto 10 meas / secLarge LCD display with bright white backlightUltra low power consumption, battery powered for 24hours of continuous useAutomatic identification function (Ai).Percentage display & 4 tolerance comparator : 1%, 5%, 10% & 20%9V battery & External power supplyAutomatic correction function with datahold, max. / min. / average recordingUtility function configuration & current setup recovery after power offStandard Mini-USB interface, SCPI compatibleAuto power OffConstant output impedance : 100 ohm
-
product
Battery Analyzers
CA 1550 – Commercial Version
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
product
Shoes and Wrist Strap Tester
WST100
• Tester designed for checking the conformity of operators wrist strap and/or shoes to the ESD protection standard.• It is also designed to be permanent wall mounted in a production facility for daily testing of employee’s wrist straps and footwear.• Easy to operate, red and green LEDs give clear “pass” or “fail” indication• Individual tests for the wrist strap, the right and left shoe• Can register up to 60 000 different measurements• Output for interface with PC or automatic door opening system• Operates battery that can be supplemented with an AC net adaptor• Tester and calibration plug are delivered with a certificate ofcalibration
-
product
Anemometer
Kt-816A
Date holdWind chill indicationTemperature display in Celsius or FahrenheitMeasure wind speed in Current/Average/Max /MinLow battery warningLCD back-lightAuto power/Manual off
-
product
Regulated Transmitter
TIP One
The TIP One is purposely designed for shallow induced polarisation or Resistivity sounding investigations. The TIP One injects a regulated current or regulated voltage into the ground via a simple 12V battery.
-
product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
43-752A-111
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
LCR Measurement
LCR component bridge with built-in test fixture and limits comparator with binning. Micro-ohmmeter with four terminal Kelvin clip leads. High basic accuracy, rechargeable battery operation.
-
product
DC/DC with UPS and Charge Controller
A wide input range, quad output PC/104-Plus DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40 to +85C without a fan or heatsink making it ideal for industrial applications.
-
product
NI-9212, 8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module
782975-01
8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module - The NI‑9212 offers channel‑to‑channel, isolated thermocouple input channels. The NI‑9212 channel‑to‑channel isolation protects channels from continuous voltages up to 250 Vrms and transient (withstand) voltages up to 1500 Vrms. You can use the NI‑9212 in a variety of applications that are not conducive for bank-isolated channels such as white goods testing, in-vehicle data logging, battery stack testing, as well as in various other noisy industrial environments.
