Filter Results By:
Products
Applications
Manufacturers
- Frequency Devices Inc.
product
High-Pass Filters
is an electronic filter that passes signals with a frequency higher than a certain cutoff frequency and attenuates signals with frequencies lower than the cutoff frequency.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 24 Channels, 24 Single-Ended Inputs
DN6.442-24
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.442-16
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3PCI
The AAF-3PCI is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier PCI bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Signal Chain µModule Receivers
µModule®
Analog Devices µModule® (micromodule) receivers consist of high performance, high speed ADCs with fixed-gain, high speed amplifiers and antialias filters. Our integrated ADC and driver products include integrated bypass capacitance and simplify the high frequency layout required to preserve ac performance. The board space savings are significant for instrumentation applications such as spectrum analyzers, oscilloscopes ,and communications test equipment, or for communications applications such as high sensitivity receivers, software-defined radio (SDR), or signal intelligence receivers. Our portfolio uses system-in-package (SiP) technology similar to multichip modules (MCM) to integrate components with different technologies, along with passive components to make an integrated subsystem.
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 24 Channels, 24 Single-Ended Inputs
DN6.445-24
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.445-16
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.445-12
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
SWITCHABLE FILTER BANKS
AFS-12WB
Matrix Test Equipment Incorporated
Models AFS-12WB contain banks of Matrix Model FLT-1 filters. Each filter may be individually selected. The Model AFS-12WB retains the manual operation in addition to remote control through the GPIB IEEE-488 interface. Optional internal Post Amplifier PA-20-20 with a gain of 0, 17 and 32dB @ +5dBm max..
-
product
16-Channel VME Multi-Range Digitizer
V490
The V490 includes 16 independent acquisition channels, each with a programmable-gain differential amplifier, analog anti-aliasing filter, 16-bit analog-to-digital converter, and digital post-processing. With a dedicated A/D converter per channel, the V490 provides true simultaneous sampling, which can be extended across multiple V490s or triggered from an external TTL signal.
-
product
Switch Matrices
Mercury System’s family of rugged, custom-designed switch matrices are available in rigid PCB construction, module-based packages, or rack-mount solutions. Each switch matrix is a highly integrated, SWaP-optimized assembly consisting of an assortment of switches, filters, amplifiers, attenuators, limiters, and drivers. The result is high speed channel selection, high isolation, high linearity, and low insertion loss.
-
product
Amplifiers
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.447-02
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Vector Network Analyzers
One of the most important measurement tasks in radio engineering is the analysis of electrical circuits. A network analyzer is an instrument that is designed to solve this problem with high accuracy and efficiency. The circuits that can be analyzed with network analyzers have a wide range of applications ranging from simple devices such as filters and amplifiers to complex modules used in communications satellites. PLANAR specializes in the development and production of vector network analyzers that combine the capabilities of scalar network analyzers that measure not only the amplitude components of the main characteristics of the system (gain, loss, standing wave ratio, etc.), but also allow measurements of the amplitude and phase characteristics of the system .
-
product
Low Noise Dual Band VCO
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
product
GPS Filter Amplifiers
Mercury Systems’ family of GPS filters/amplifiers is the right choice for your high reliability GPS receiver. Whether your application is ground, airborne, missile or launch/reentry vehicle, you can trust the technology behind these advanced products. Custom designs including multiple outputs and integrated receiver protection limiters are also available.
-
product
Telephone Attenuators & RFI Filters
Despite the growth in digital and fiber systems, many telephone companies still require basic line treatment products. Wilcom's hard-to-find line treatment products help the telecommunications industry deliver the performance the customer expects. Products include line powered amplifiers and RFI filters.
-
product
Video Op Amps
Analog Devices video amplifiers, buffers, and filters provide an ideal solution for your video amplification needs. Our easy to use amplifiers require few external components, with on-chip options available to help you minimize design time.
-
product
Radio Frequency (RF) And Microwave Products
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
product
DVB-T Amplifier Module
The COMM-connect DVB-T Amplifier Module is a very versatile module, for use in multiple applications, including driving High Power amplifiers or stand alone Gap-filler. The amplifier covers both VHF & UHF bands, and can be combined with several COMM-connect filter options.
-
product
Short Light Source
LM-AS
The short light source is compatible with the LM-101 or the LMC-20. The light is supplied with a 50 watt tungsten halogen convection cooled light source which provides suffcient energy for use with narrow band pass filters or monochronomators in the wave length range of .35 to 2.5 microns. The light beam is chopped at 200 hz by a quiet, vibration free, synchronous motor. The housing also contains a secondary LED light source and detector for synchronization of the amplifier, plus an electro-mechanical shutter to block the light output when the instrument is zeroed. An internal collimating lens produces a narrow beam (<1") so the LM-AS can be used in bell-jar and large coating systems.
-
product
Motion Control Components
- Control of versatile robotic structures, including "yaw", "pitch" and "roll" motion capabilities- S-curve velocity profiling, based on polynomial splines and Bernstein-Bezier curves- Continuous path control in multi-segment smooth trajectories- Synchronization of multiple axes- Trajectory control with user defined velocity profiles- Kinematical modeling of open and closed loop mechanisms- Singularity consistent path planning and singularity avoidance- Optimal PID filter tuning- Automatic adjustment with respect to the surrounding equipment (cassettes, process stations, etc.)- Tilting capabilities in terms of the end-effector frame- Compensation for deflection of the end effector, the manipulated object and geometric in accuracies of the arm Scanning and Aligning Features- Wafer mapping based on through-beam or reflective sensors- Automatic detection of the planarity and the center of wafers and FPD- Non contact FPD aligning. Misalignment compensation on the fly Safety- Programmable travel limits- Position tracking error detection- Amplifier overload protection- Emergency stop
-
product
Tracking Generator
TG44A
The Signal Hound USB-TG44A is a 10 Hz to 4.4 GHz tracking generator which works with your USB-SA44(B) to measure filters, attenuators, amplifiers and more! It is compact, simple to use, and an effective troubleshooting tool for general lab use, engineering students, ham radio enthusiasts, and electronics hobbyists.
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.448-08
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
RF Training Kit And Lab Sheets
Y1800A
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
product
RFFE Protocol Analyzer and Exerciser
PGY-RFFE-EX-PD
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.445-04
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Amplifier/Filter Module
SCS-818
The SCS-818 and SCS-819 amplifier/filter module provides eight 4-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-818) and 0.5Hz to 70kHz(SCS-819). Each of the SCS-818/SCS-819's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
