Filter Results By:
Products
Applications
Manufacturers
- Cytec Corp.
product
Solid State Digital Matrix Switching Systems
DX Series
Cytec's DX Series Switching Systems are based on solid state switch fabric. All systems are non-blocking (any input to any output) and full fan-out (any input to any or all outputs)
-
product
Universal Test System
LS6601A
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
product
cDAQ-9188, 8‑Slot, Ethernet CompactDAQ Chassis
781424-01
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
cDAQ-9184, 4‑Slot, Ethernet CompactDAQ Chassis
782069-01
4‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9184 is a CompactDAQ Ethernet chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement. With multiple timing engines, you can run seven hardware‑timed operations simultaneously, with three independent rates for analog input.
-
product
ISC-1780, VGA, 1.58 GHz Processor, Monochrome/Color Smart Camera
785140-01
The ISC‑1780 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
ISC-1780, VGA, 1.58 GHz Processor, Monochrome/Color Smart Camera
785143-01
The ISC‑1780 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
Virtex UltraScale+ HBM FPGA Processor - SOSA Aligned 3U VPX
Model 5586
- Jade 5585 and 5586 FAQ- Co-processor for distributed FPGA processing tasks- High-Bandwidth Memory (HBM) delivers 20x more memory bandwidth than traditional DDR4 solutions- Board interfaces: 1 GigE, 10 GigE, 40 GigE, dual 100 GigE and PCIe- High-bandwidth memory, FPGA logic and DSP density make this board a single-slot 3U VPX proessing powerhouse- Features Xilinx Virtex UltraScale+ HBM FPGAs- 10 GigE Interface and 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 46, VITA 48.11, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled- Navigation Design Suite for software and custom IP development
-
product
Master-Slave Distributed Motion & I/O Master Controller
PCIe-7856
The PCIe-7856 is a PCI Express interface card providing two ports for Motionnet and HSL systems for distributed motion and I/O in machine automation applications. HSL technology allows thousands of I/O points to be scanned at the millisecond-level in real time by using a master-slave architecture.
-
product
Dynatrace Application Monitoring
Start Dynatracing your applications in minutes with easy deployment and zero-configuration.Auto-discover and map all applications and transaction-flows in your distributed environment.Leverage self-learning baselines with alerts, out-of-the-box dashboards and auto-correlated system monitoring.Find problems before your users notice them with smart, early production error detection.Configure, manage and update easily with a centralized configuration consoleeven for thousands systems.Enable easy access for everyone who needs it. Provide one system valuable to all stakeholders by de-coupling system access and performance analysis.
-
product
Gas & Flame Detection System
Syntel
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
product
Distributed Data Acquisition
Distributed Data Acquisition seamlessly networks all the components of your integrated monitoring system. The resulting synchronization decreases the quantity and lengths of communications wires between sensors and the data-acquisition system (DAQ).
-
product
Backplane & Cable Test
Backplane and cable test systems from Terotest include LINX, a fixtureless test system. Each LINX test card plugs directly into the unit under test, which removes the necessity for long test cables and fixtures. This is called distributed testing and results in dramatically lowered costs. LINX is extremely easy to use, with a self-learn function or input from CAD.
-
product
Edge Gateway
The Edge Gateway provides a solution to manage distributed wireless sensors. On the one hand, new sensors can be added to the measurement systems easily and on the other hand, the gateway is powerful enough to evaluate the measurements and detect irregularities.
-
product
ISC-1781, 1.3 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785146-01
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
DAS Antennas
In-Building Distributed Antenna System (DAS or i-DAS) antennas are low profile and designed to be mounted discreetly to a hard or tiled ceiling. Used in a series throughout large buildings, campus areas or even in below ground sections of a building the antennas can provide a distributed LTE or Wi-Fi signal to where it is required most. With a growing demand for in-building connectivity and higher data rates, larger smart or connected buildings require a series of antennas in order to distribute signal around the building or campus area.
-
product
Distributed 4-Axis Motion Control Modules (With High-Speed Trigger Function)
MNET-4XMO-(C)
The MNET-4XMO is a 4-axis motion controller module for Motionnet distributed motion systems. It can generate fast frequency pulses (9.9 MHz) to drive stepper or servomotors in the machine automation field. As a motion controller, it can provide comprehensive motion functions which include 2 axis circular interpolation, 2-4 axis linear interpolation, or continuous interpolation for continual velocity and so on. Also, changing position/speed on the fly is available with a single axis operation.
-
product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-01
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
product
Timing Signal Generator
OSA 5548C TSG
Our OSA 5548C Timing Signal Generator (TSG) is a scalable synchronization solution ranging anywhere from 20 unprotected outputs up to a thousand protected outputs by adding up to four expansion shelves to the core unit. Its ultra-compact footprint makes it ideal for telecom operators to provide scalable network synchronization in over-crowded exchanges. The OSA 5548C TSG’s distributed intelligence message passing system eliminates single points of failure and guarantees reliable uptime. Core unit and expansion shelves share the same modules, minimizing overall administrative complexity and enabling reduced homologation activity.
-
product
cRIO-9055, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 4-Slot CompactRIO Controller
787043-01
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9055 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
3U VPX Single Board Computer
VP32002
LinkedHope Intelligent Technologies Co.,Ltd.
VP32002 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32002 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32002 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, two UARTs and two USB interface.The board provides a flexible PCI-Express bus interface to the backplane. The interface can be configured as follows: 1 Port x8 PCIe, 2 Ports x4 PCIe, 4 Ports x2 PCIe. This feature makes it suitable for either distributed switching system or centralized switching system.For the user to quickly form application solutions, LinkedHope provide VP32002 a complete driver package including Windows, VxWorks, Linux and QNX.
-
product
Bridge Monitoring
Structural Health Monitoring of BridgesDewesoft data acquisition systems are used in structural health and seismic bridge monitoring projects ranging from structural mechanics to continuous monitoring of large, complex structures. The systems provide distributed, high-channel-count and remote monitoring for highway overpasses, roads, buildings, and bridges.
-
product
Master-Slave Distributed Motion & I/O Master Controller
PCIe-7853
The PCIe-7853 is a PCI Express interface card HSL systems for distributed motion and I/O in machine automation applications. HSL technology allows thousands of I/O points to be scanned at the millisecond-level in real time by using a master-slave architecture.
-
product
ISC-1783, 5 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785153-01
The ISC‑1783 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
Gunshot Detection & Localization System
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
product
Fixed Laser Source Module
Keysight offers a broad choice of fixed laser sources, which are available as single-wavelength and dual-wavelength modules as part of the Keysight Lightwave Solution Platform. The Keysight 8165xA Fabry-Perot laser sources can be used in conjunction with optical power meter modules for insertion loss, optical return loss and PDL measurement of broadband components and fiber. The Keysight 81663A Distributed Feedback Laser Sources are best suited for amplifier test and WDM system test applications. Keysight covers PON and common WDM wavelengths with its 81663A Distributed Feedback (DFB) laser source modules. The precise tunability around ITU-grid center wavelength gives you the flexibility to match test setups to the latest requirements of the DWDM-system. The fine-tuning allows to shift the center wavelength from one DWDM transmission channel to the adjacent channel in dense WDM systems. The built-in isolator ensures highest laser stability, even when reflections are present in the optical path.
-
product
EtherCAT Slave System
EPS Series
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833X Series master controllers, EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EPS slave system brings the power the flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EPS system with comprehensive and high-density I/O modules that include DI/O, pulse-chain motion modules. Leveraging ARM and FPGA technologies, the EPS slave is able to monitor and report system integrity via EtherCAT communication, while relay module lifecycle and signal integrity of analog output are monitored cyclically, and hot swappability reduces downtime significantly. Uniquely designed for full operability in conditions from -20°C to 60°C,the EPS slave system is also fully compliant with the EN 60068-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certification. Corresponding ESI files for each EPS system can be generated thru ADLINK's Windows-based EtherCAT slave utility, LinkMasterPro™.
-
product
Test Hardware
TTPSimulate PCI
TTPSimulate supports hardware-in-the-loop simulation and design of complex distributed control systems where some parts of the systems are physically available and others exist only as a simulation model. This board enables concurrent engineering and reliable integration of complex integrated systems in large programs.
-
product
cDAQ-9185, 4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785064-01
4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9185 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
product
Performance Testing
Our Load Testing and Performance Testing expertise spans many technologies, including web, mobile, distributed, cloud databases, high-volume transaction systems, and more. UpDoer Technology is dedicated to professional excellence in all that we do for our many clients across the globe.
-
product
High Voltage Cable/Harness Test System
CKT1175-50
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
product
DC/DC Power Supply
PCM-DC-AT512-P
WINSYSTEMS’ PCM-DC-AT512-P is a triple output, DC/DC power supply that can mount anywhere in a PC104 stack. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/ COTS, security, solar-powered, and telecommunications.
