Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Signal Patchcord, RCV, SIM VTAC, 72", DVI-D Male Single Link, 4 Position
7-142706735
Signal Patchcord, RCV, SIM VTAC, 72", DVI-D Male Single Link, 4 Position
-
product
PCIe-1433, Base-, Medium-, Full-Configuration Camera Link, PoCL Compatible Frame Grabber Device
781169-01
The PCIe‑1433 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PCIe‑1433 includes an onboard … FIFO for higher bandwidth use cases, and it works with any base‑, medium‑, and full‑configuration Camera Link camera. The PCIe‑1433 is ideal for many industrial, life science, and biomedical imaging applications. The PCIe‑1433 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables.
-
product
Accessories & Cables
Active Silicon offer a range of accessories for our hardware products, including CoaXPress and Camera Link cables and FireBird IO adapters for use with our frame grabbers. The products listed on our website are in stock and readily available. Other cable lengths or adapter types, are available on request, especially for higher order volumes.
-
product
FireBird Camera Link Frame Grabber (1xCLD-2PE8)
AS-FBD-1XCLD-2PE8
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
-
product
FireBird Camera Link Frame Grabber
AS-FBD-1XCLD-2PE4L
FireBird Camera Link Deca Low Profile is a member of Active Silicon's state-of-the-art FireBird frame grabber family. The low profile design allows the FireBird Low Profile board to be used in small embedded PC enclosures and rackmount cases where full height PC cards are not suitable. A full height bracket option of this product is available for use in standard PC form factor enclosures. FireBird is designed for ultimate performance providing the very fastest image acquisition without any CPU intervention using the latest FPGA families, DDR3 memory, and a fast Gen2 PCI Express interface.
-
product
Area Scan Camera
Area Scan Cameras provide high-performance and high-resolution options that offer excellent image quality and many sensor options. They can connect over a variety of interface standards such as USB3 Vision, GigE Vision, and Camera Link. Models offer high frame rates and rolling or global shutters. Area Scan Cameras are well suited for a variety of applications, such as automated inspection, smart machine control, and factory automation.
-
product
Camera Link Translators
CLT-303
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
product
Digital VIS-SWIR Camera
OWL 1280
Using a 1280 x 1024 InGaAs sensor from SCD, the OwL 1280 offers visible extension from 0.6µm to 1.7µm to enable high sensitivity imaging. The 10µm x 10µm pixel pitch enables the highest resolution imaging. It will offer less than 28 electrons readout noise (rms) and with a high intra-scene dynamic range of 51dB, this enables simultaneous capture of bright & dark portions of a scene. Available with a 12 bit medium Camera Link digital output, the Owl 1280 will run from 10 to 60Hz. The camera features an on-board Automated Gain Control (AGC) which enables the best contrast image from low to bright light. The camera also has an on-board intelligent 3 point Non Uniform Correction (NUC) providing the highest quality images. As with all Raptor cameras, the Owl 1280 is ultra compact and rugged. The camera sensor temperature is stabilised to 15°C and the camera does not have a fan.
-
product
Grablink DualBase
For two Camera Link Base or Lite configuration camerasDirectly compatible with hundreds of Camera Link cameras available on the marketSupports PoCL, Power over Camera LinkECCO: Extended Camera Link cable lengthPCIe x4 bus: 850 MB/s sustained delivery bandwidthFeature-rich set of 20 digital IO linesMemento Event Logging Tool
-
product
Cable, Power over Camera Link (PoCL), MDR to MDR, 5M
199744-05
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
product
Electro-Optical Test Software
INFRATEST
INFRATEST is a powerful software for testing IR cameras, visible and NIR cameras, ICCDs, goggles and laser rangefi nders. Based on video acquisition modules compatible with a wide range of communication protocols, including LVDS, Camera Link, GigE Vision and all types of analog formats – CCIR, PAL, RS170, NTSC, INFRATEST acquires, displays and analyzes the video signal from all types of electro-optical devices.
-
product
FastCamera
FC1700
The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
FastCamera
FC200
The FastCamera 200 is a high-speed 2 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
Framegrabber
FastX1703
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
-
product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
product
Grablink Base
For one Camera Link Base or Lite configuration cameraDirectly compatible with hundreds of Camera Link cameras available on the marketSupports PoCL, Power over Camera LinkECCO: Extended Camera Link cable lengthPCIe x1 bus: 200 MB/s sustained delivery bandwidthFeature-rich set of 10 digital IO linesMemento Event Logging Tool
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
product
PCIe-1477, 80-Bit Camera Link, PoCL-Compatible Frame Grabber Reconfigurable Device
786502-01
The PCIe-1477 works well for deployment systems and features a user-programmable FPGA for onboard image processing. Placed directly in the image path, FPGAs can acquire and process images with closed-loop control without CPU intervention. This technology is also suitable for high-throughput system architectures to preprocess image data on the FPGA and then send the data to the CPU for further processing and decision-making. The PCIe-1477 also supports Power over Camera Link (PoCL), which you can use to power cameras through PoCL-enabled cables.
-
product
Frame Grabbers
* Supporting most performance-demanding Machine Vision protocols, such as CoaXPress, Camera Link HS, 10 GigE, Fiber etc.* Ideally suited for industrial, defense and aerospace Machine Vision Systems.* These products are complimented by sophisticated application software package and SDK, for Windows and Linux OS’s.
-
product
Virtex-5 XMC/PMC
XMC-FPGA05D
Curtiss-Wright Defense Solutions
The XMC-FPGA05D high density I/O module controlled by a user programmable Xilinx Virtex-5 FPGA and supported by a range of front panel I/O modules including analog I/O, RS-485/422, LVDS and Camera Link.
-
product
acA2000-340kc, Color Camera Link, 2 MP, 340 FPS Area Scan Camera
782143-01
The acA2000-340kc is a Color Basler Ace Camera Link Camera with a 2 MP resolution and a maximum image acquisition speed of 340 frames per second. The acA2000-340kc uses a CMV2000 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
product
Digital Camera Hop Transmitter
DCHT
The DCHT portable digital stereo transmitter is designed for use in film and TV production as both a wireless audio link from a bag or cart system to cameras and as a portable IFB transmitter paired with the Duet digital wireless M2R receiver packs. The DCHT accepts two channels of mic or line level analog signals or an AES digital signal from a mixer and transmits to the receiver or receivers in a purely digital format. The digital architecture of the new DCHT is a third-generation design with specially developed, high-efficiency circuitry for extended operating time on two AA batteries.
-
product
Camera Link Frame grabber
Cyton-CXP
CoaXPress (CXP) is a simple, yet powerful, standard for moving high speed serial data from a camera to a frame grabber. Video is captured at speeds of up to 6.25 Gigabits/Second (Gb/S). Simultaneously, control commands and triggers can be sent to the camera 20 Mb/S (with a trigger accuracy of +/- 2 nanoseconds). Up to 13 W of power can also supplied to the camera.
-
product
FireBird Camera Link Frame Grabber (2xCLD-2PE8)
AS-FBD-2XCLD-2PE8
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Grablink Full XR
For one Camera Link 80-bit, 72-bit, Full, Medium or Base configuration cameraDirectly compatible with hundreds of Camera Link cameras available on the marketSupports PoCL, Power over Camera LinkECCO+: Double Camera Link maximum cable lengthPoCL SafePower compliantPCIe x4 bus: 850 MB/s sustained delivery bandwidthFeature-rich set of 10 digital IO linesMemento Event Logging Tool
-
product
Framegrabber
FastX-APU
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
product
Miniature 12G/3G/HD-SDI Fiber Transport
SilverBULLET Series
Sometimes you just need that “silver bullet” - a simple solution that solves problems. Maybe it’s a quick connection to support temporary video and audio feeds, or perhaps just a rock-solid fiber-optic connection for single-link transport to and from a camera. MultiDyne’s SilverBullet Series offers an economical solution for broadcast-quality signal transmission on single-mode fiber. At just three inches, the SilverBullet offers a compact, interlocking architecture to ensure robust links that can fit just about anywhere. SilverBullets come in a compact carrying case that includes the DC power supplies. Ideal for a wide variety of broadcast and professional AV applications including field production, remote camera links, courtesy feeds, cross-campus production and pre-fibered venues.
-
product
Phoenix Camera Link Frame Grabber (D48-PE4H)
AS-PHX-D48CL-PE4H
Phoenix-D48CL x4is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
PXIe-1435, Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module
781699-01
Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module—The PXIe‑1435 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PXIe‑1435 works with any base‑, medium‑, and full‑configuration Camera Link camera, and it is ideal for many industrial, life science, and biomedical imaging applications. The PXIe‑1435 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables. The onboard digital I/O includes four TTL, two optoisolated inputs, and one quadrature encoder.
-
product
Camera Link Simulator
CLS-221
The CLS-221 Camera Link Simulator is an affordable, high-performance video test pattern generator that supports all video formats including those introduced in the new version 2.1 specification. Fully programmable video timing enables the CLS-221 to mimic the characteristics of almost any camera. New features include enhanced timing performance, bayer color support, and additional video patterns. Control is via an RS-232 port, USB, or frame grabber COM port. The CLS-221 also incorporates the AIA validation test pattern.
