Filter Results By:
Products
Applications
Manufacturers
9V Battery
a snap-on connection type battery. AKA: 9 Volt Battery
See Also: Battery, Lead Acid Battery, AAA Battery, AA Battery, 1.5V Battery, Button Battery, C Battery, Coin Battery, D Battery, NIckel Cadmium Battery, Lithium ion Battery, SLA Battery, VRLA Battery, NICAD
- Pickering Interfaces Inc.
product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 1 kV Isolation
43-752A-113
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Differential Voltage Probes
DP150/DP200pro
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
product
LCR Meter
Basic measurement accuracy 0.1% & speed upto 10 meas / secLarge LCD display with bright white backlightUltra low power consumption, battery powered for 24hours of continuous useAutomatic identification function (Ai).Percentage display & 4 tolerance comparator : 1%, 5%, 10% & 20%9V battery & External power supplyAutomatic correction function with datahold, max. / min. / average recordingUtility function configuration & current setup recovery after power offStandard Mini-USB interface, SCPI compatibleAuto power OffConstant output impedance : 100 ohm
-
product
Multi-purpose Cable Tester and Cable Tracer
165 CB
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
product
Professional 3-Axis Digital Gaussmeter
IDR-fw4090/E
Integrity Design and Reseach Corp.
For professional results, this meter offers the ultimate in accuracy and features: extended frequency bandwidth, superb accuracy, 3-axis modes, auto-ranging from 0.1 to 1999 mG, Hand held, and completely self-contained, it is extremely fast and easy to use. Simply turn the unit on and take true RMS 3-axis readings. This is a really fine piece of equipment at a great price. Made is USA by FWBELL. Full year warranty. Accuracy traceable to NIST standards. 9V battery included.
-
product
Digital Panel Meter
ST-312V (ST-312mV)
Standard Electric Works Co., Ltd
● 3 1/2 digit liquid crystal display.● 200mV and 2V full scale input sensitivity.● Single Battery operated 9V supply or ±5V DC power supply (Dual supply).● Built-in low battery indication and automatic polarity indication.● Decimal point selectable.● Low power dissipation Typically less than 20mV.● High input impedance (> 1M ohm).● Guaranteed zero reading for 0 volts input on all scales.● True differential input or single-ended input.● Self mountable with optional mounting bezel.● Low cost high performance.● EN 50081-1 EN 50082-1 EN 55022 EN 61000-4-2 IEC 801-3
-
product
Battery Tester
6470 BT
Standard Electric Works Co., Ltd
2000 counts. DC Voltage measurement. 4-wire resistance measurement. Data hold function. Low battery indication. 9V DC power supply. Measure battery types: Li-ion, Ni-Cd, Ni-MH. Simple operation. Lead resistance and contact resistance eliminated.
-
product
DMX Tester
DXT1
The new DMX Tester from NuDelta Digital is a feature-packed test tool you won't want to leave home without. It can send any level to any DMX address with simple commands similar to those found on the world's most popular lighting consoles. It can test for valid DMX signal and show you the level at any address. It can test continuity on all five pins of a standard DMX cable and indicate which pins are not connected or cross-wired. Runs for hours on a 9 volt battery (included).
-
product
Safety Voltage Detector
305 SVD
Standard Electric Works Co., Ltd
● Bright LED visual indication● Audible indication● AC voltage detection: 100Vac ~ 69kVac ● Frequency range: 40 ~70Hz ● Easy-to-prove method● Self-test function● Power source: 9V alkaline battery ● Non-contact detection by proximity● Convenient to use● Operating temperature and humidity: 0°C~40°C / 80% RH Max.● Lightweight, robust and compact● Easy access to battery● Comply with EN 61326-1
-
product
Pocket Pro Shot Timer
The Pocket Pro measures shot time intervals for personal practice and scoring matches! A timeless design that has set the standard for shot timers. Requires one 9 volt alkaline battery for operation.
-
product
Digital Bridge
KT-8280
Large 0.78" LCD , 1999 counts, all enunciators displayVector MeasurementFour Terminals MeasurementDissipation Factor MeasurementWide range, high accuracyTest Frequency: 1 KHzPower consumption less 5 mAPower Sources:9V transistor type battery (Neda 1604)Complete with : Four Terminal Mode alligator clip leads, rubber holster, AC power adapter, carrying bag
-
product
Professional Automotive DMM
590
Another good choice for the professional automotive technician, the #590 puts the right cababilies in your hands. For example, the #590 can test the on-time of fuel injectors using the Ms pulse width test function. This DMM is completely auto-ranging, making it an easy and efficient tool to use. The #590 includes two sets of test leads, RPM pick-up, temperature probe, 9 volt battery, instructions manual and carrying case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
product
Smoke Detection Sensor – 120VAC Wire-In with Battery Backup
ENVIROMUX-SDS-120V
For warning of smoke and invisible fire particles. Ionization smoke detector. Applications from 40°F to 100°F (4°C to 38°C). Front loading battery door. 9V battery backup (included) in case of power failure. One button design for easy testing and HUSH mode activation control. LED indicates four modes of operation: standby condition, alarm condition, alarm memory and hush mode. Hush mode: silences false alarms for 8 minutes, or low battery warning for 13 hours. Voltage supply: 120VAC. Pre-stripped wiring harness with tinned strands. Audio alarm: 85dB at 10ft. Dimensions: 5" diameter x 1.75" depth. Dust cover prevents false alarms. Tamper resist feature. Links with up to 24 devices. Max distance between first and last device: 1000ft (305m). Alarm memory indicates initiating alarm in interconnected systems. Use compatible relay (ENVIROMUX-RLY-SDS120V) for connection to the ENVIROMUX system or other auxiliary warning devices such as external sirens or stairwell lighting. ENVIROMUX-RLY-SDS120V includes normally open and normally closed contacts. Contact ratings: 10A at 120VAC, 5A at 30VDC. Regulatory approvals: UL.
-
product
High Quality Cable Tracker LAN Finder
specification:*Working current:Tester:10mA Receiver:30mA*Signal transfe mode: Digital signal*Signal output level:8Vp-p*Signal transfer distance:3Km*Power:by 2 × DC 9V Battery(not included)
-
product
Battery Analyzer
KT-99/99A
Measure battery storage capacity with clamp-on sensorTest battery capacity under it’s real working conditionSelect different type of battery with discharge end voltageDisplay current and voltage during testingDisplay battery parameters and timeAuto-alarm when test finish,alternatively data savingAuto backlight on in dark areaMaximal capacity count up to 999.9Ah4-wires mode impedance measurement Up to 0.01mΩ resolutionOperating Environment: 0～40℃ ,<80% R.HStorage Environment : -20～60℃ ,<80% R.HPower supply: Heavy duty 9V Alkaline battery ( IEC-6F22)Accessories: “4 wire” test leads 1 pair “2 wire” test leads 1 pair
-
product
Cable Tracers
162 CB
Standard Electric Works Co., Ltd
Filter Probe● Works with any Tone Generator to identify wires.● Volume control for increasing sensitivity and adjustable to suit work environment.● 2 operation modes: Filter on / Filter off.● The auto-off function (5 minutes) prevents battery consumption.● Power supply is available in any 9V battery with a life of approximately 50 hours.● A phone jack is designed for headset or handset.● Flashlight function.Tone Generator● Tone Generator is a great tool for locating and identifying cable pairs or individual conductors.● 162 CB-G doesn't only provide the function of a tone generator, but also serves as a continuity and polarity tester.● A tone selector switch located inside the unit for selection of the fast tone or the slow tone.● Two bi-colored LEDs for Line1 and Line 2 indication of the polarities of the telephone lines.● The unit has alligator type terminals, a modular cable of 4 conductors with a strong connector.● The tone and continuity functions are only applied to Line1. (Modular connector)
-
product
Non-Contact H.V. Detector
380 HP
Standard Electric Works Co., Ltd
● Protection class : IP65.● 7 voltage settings : 120V, 4kV, 15kV, 25kV, 35kV, 46kV, 69kV● Bright LED visual indication● Vibration function● Frequency range: 40~70Hz● Audible indication● Easy-to-prove method● Power source : 9V rechargeable battery● Can be charged with the automotive● Non-contact detection by proximity● Compatible with most hot sticks● Lightweight, robust & compact● Special ranges are available upon request● Flashlight function● Safety standard : EN 61326-1 CISPR 11● Operating temperature and humidity : 0°C ~ 40°C / 80% R.H. Max. ● Dimensions: 262(L) × 85(W) × 56(D)mm● Weight: Approx. 330g
-
product
Digital Anemometer
AM-4826
MEASUREMENT RANGE： 0.4～30.0m/s 1.4～108.0km/h 80～5910ft/min 0.8～58.3knots. POWER SUPPLY:9V 6F22 BATTERY
-
product
50 Ohm Bridge / Freq Counter
* Generates a 3 to 30 MHz low level signal displayed on small 8 x 2 LCD * 50 ohm bridge supports tuning 50 ohm antennas * Adjust POT to find the resonate frequency of antenna * 30 turn POT allows easy smooth frequency adjustment * Bright red LED extinguishes when bridge is balanced * Function switching allows for use as frequency counter * 50 ohm termination included * measures 5.5 x 2.5 x 1.1 inches * 9 volt battery operation
-
product
Digital Multimeters
ST-3501
Standard Electric Works Co., Ltd
● Display: 3½ digit liquid crystal display (LCD) with max. reading of 1999.● Polarity: Automatic, (-) negative polarity indication.● Zero Adjustment: Automatic.● Over Range Indication: Highest digit of (1) or (-1) is displayed.● Low Battery Indication: The (BAT) is displayed when the battery voltage drops below the operating voltage.● Measurement Rate: 3 measurements per second, nominal.● Operating Temperature: 0°C to ±50°C, 0-70% RH.● Storage Temperature: -20°C to +60°C, 0-80% RH, with battery removed.● Accuracy: Accuracy specifications at 23±5°C, less than 75% RH.● Power: Single, 006P 9 volt battery● Dimensions: 128(L)×72(W)×33(D)mm.● Weight: Approx .200g
-
product
Thermometer REPLACED BY PTM-1
BA T-7001H
In applications where clinical accuracy is not mandatory and cost is a consideration , the BAT-7001H is Physitemp‘s most compact, low cost thermocouple thermometer. The Model BAT-7001H is a high performance, precision hand-held instrument for the measurement of temperature using Type T (copper-constantan) thermocouples. This versatile instrument measures temperature in both °C and °F. The internal memory of the micro-computer stores the minimum and maximum measured temperature for instant recall via the LCD display. BAT-7001H operates on a 9V battery.
-
product
Digital Multimeter
KT-820C
3 ½ digits with a maximum reading of 1999. Continuity / Diode / hFE functions. Square wave output function. Data hold for easy reading. Temperature Test. Power supply: single standard 6F22 9V battery
-
product
Surface Resistance Meter
SRMETER2
The Surface Resistance Meter is a wide range, multi-scale, auto-ranging meter. This meter is appropriate for auditing static control work surfaces.The meter is 9V battery powered and simple to use.NIST Calibrated
-
product
Digital Tesla Meter
HT208
Model HT208 digital teslameter is controlled by the SCM,which is suitable for handle operation.It can be used to measure DC or AC magnetic field and flux dencity.The device can be carried on one’sperson. It is characterized by its wide measuring range,simple operation and clear display. It is still added with the function of maintenance such as holding Measure Value/Peak Value,As mT or Gs unit of display can be change over,Measuring range of 200mT or 2000mT can be choosed,and others that as reseting zero by key and so on. The power is one piece of battery 9V. It can be used continually about 20 hours
-
product
Capacitive H.V. Detectors (Contact)
213 HVD~226 HVD
Standard Electric Works Co., Ltd
● Excellent shock resistance.● Rugged nylon moulding.● Auto on (when voltage detected).● Excellent drop resistance.● Good vibration resistance.● Loud sound alarm indication.● Built-in proving and self-test circuit.● High bright color-coded LEDS.● Works from standard 9V battery.● Interchangeable contact electrode.● Use in all whether conditions.● Compatible with all link sticks.● Lightweight, robust & compact.● Models available from 11kV to 132kV.● Suitable for indoor and outdoor use.● Self(auto on) or manual arming.● Easy access to batteries.● Customized threshold on demand.● Auto off (if no voltage detected).● Waterproof design, protection class : IP65.
-
product
Digital Engine Analyzer
KT-7183
0.5" (13mm) LCD Max. indication 1999 or - 1999. Engine TACHO & DWELL MEASUREMENT. Polarity: Bi-polar by automatic switching. "-" indicates reverse polarity. Over-input: Indication of "1" or "-1" Complete with test leads, 9V battery, and protective rubber holster
-
product
Mini Sound Level Meter
PSPL03
Max Hold FunctionSmall Shape for Easy PortabilityLevel Range: 35-100dBAccuracy: +/- 3dB (ref. 94dB @ 1kHz)Frequency Range: 31.5 Hz to 8 kHzFrequency Weighting: AOperation Temperature: 0 to 40C (32 to 104 F)Storage Temperature: -10 to 60 C (14 to 140 F)Battery Type: 9V (Included)Dimensions: 6.69' H x 2.28' W x 1.38' DWeight: 3.77 oz.Sold as : Unit
-
product
Personal Voltage Detectors
*Provides another level of safety for line crews, storm restoration workers and first responders*Alerts user to the proximity of electric fields or energized electrical equipment with a loud alarm and bright lights*Frequency of alarm increases as the user gets closer to the electrical hazard*Detects voltage above line-to-line*Typical initial warning distance is about 7 ft from a conductor*Warning distance increases with higher voltages*Field replaceable 9V battery with low battery indicator
-
product
Environmental (Radiation) Monitoring System
Hawk® EMS
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
product
Digital Multimeter
KT-7241A
3 1/2 LCD display , 1999 countsSample rate:2.5 times per secondLow battery, polarity, and over range indicatorAccessories: test leads, 9V battery, and protective rubber holster
-
product
DIGITAL MULTIMETER, TRUE RMS, 10A, 1KV
72-13570
*True RMS digital multimeter with 40000 counts display*CAT III 1000V, CAT IV 600V safety rating*Manual function select and auto ranging*Measure AC & DC at the same time (AC+DC)*Up to 9999 readings data storage and 0.1% to 99.9% duty cycle*Data hold, max/min/relative modes, analogue bar graph*Full icon display, double backlight*USB interface and Bluetooth connection*Powered by 9V (6F22) battery*12-month limited warranty *view Terms & Conditions for details
