Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 10A Power MUX, 5-Bank, 6-Channel
40-661-005
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
product
Load Board
cPCI 6U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Load Board
cPCI 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Electronic Loads
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
product
Load Cells and Sensors
AMETEK Sensors, Test & Calibration
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.The full bridge load cells and sensors provide high precision measurements that ensure adherence to the international standards.
-
product
Coaxial Terminations (Loads)
Keysight offers a variety of coaxial terminations (loads) solutions to terminate up to 75 Ohm coaxial systems with precise, low reflection loads for superior RF performance.
-
product
Three Phase Phantom Load Test Bench
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
-
product
C-Mic Auto Test System
BK9010B
Based on the BK3010V2 C-Mic Tester, the BK9010B is our fastest C-mic test system. Fully automatic, the BK9010B loads the mics in place and after testing, it sorts passing microphones into 8 quality classes, and failing microphones according to the reason they failed. Each mic is put into its appropriate bin. As testing progresses, you can view the data graphically in real time or save it to be viewed or analyzed later.
-
product
Instrumentation/Electronics
Junction Boxes for 4 or 8 load cells in ABS, Aluminium or Stainless Steel (optionally with ATEX approval)Intelligent Junction Box for individual monitoring of load cell performance and error checking of up to 4 load cellsSimple weighing transmitters (with analogue output for connection to a PLC) or high speed transmitters with built-in weight indication, external communications, set points and dedicated check weigher functionsPurpose designed weight indicators with external communications, ATEX approval for use in hazardous areas and IP69K protection for use in harsh, wash-down environmentsDedicated weighing controllers for batching, filling, check weighing, truck weighing and axle weighing, with communications and relay outputsInstrumentation/electronics with Weights and Measures approvals (legal-for-trade), i.e. OIML R76 and EN45501:2015 (NAWI)Remote displays for secondary weight indication at a different locationLoad cell tester with intelligent diagnosticsLoad cell simulator
-
product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-40
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～600A*Current measurements of feeder
-
product
Website Monitoring
Keep a close eye on the performance and availability of your web pages with HTTP monitoring & HTTPS monitoring. Check if the web pages on your web application are reachable or not. When they are not reachable, get alerts and notifications & remedy actions follows. The website monitoring feature looks for various critical attributes such as the page response time. Set up a URL for monitoring & then define a threshold – if the webpage load time is more than 10 seconds, you should receive SMS or an e-mail. Active notifications help IT admins in taking quick corrective action before its unavailability affects end users. It also lets you make sure that CGI scripts, web server and back-end databases are performing properly.
-
product
Load Cell Transmitter
MODEL SST-LV
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
Load Cells
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
product
Load Cell Power Supply Module
MODEL PSM-F10
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
product
LOAD BOARD
The semiconductor manufacturing process is divided into a front process (WAFER) and a post process (PACKAGE). The LOAD BOARD is an INTERFACE device for inspecting the function and performance of a package state IC, which is a post process, It is an INTERFACE key device for inspection. In particular, LOAD BOARD is widely used in non-memory semiconductor inspection equipment.
-
product
Dual Channel HV Amplifier with Phase Inverter
A400DI
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
product
1800~3000W DC Electronic Loads
JT633 series
Nanjing Jartul Electronic Co., Ltd
JT633 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT633 series load very suitable for testing power supply when produced in large quantity. Besides, JT633 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT633 series load satisfing most of R&D requirements.
-
product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
product
Load Cells & Force Transducers
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
product
Accelerated Product Life Cycle
Delserro Engineering Solutions
Under normal conditions it may take years to gather failure data on the life cycle of new products. Through accelerated life testing the overall time to failure can be reduced to weeks by increasing the frequency of the field loads and by removing insignificant stress components. In addition, life cycle testing on a product can be reduced or accelerated dramatically by increasing the stress levels to higher than normal. Putting a product through Accelerated Life Testing can reduce test time from weeks to days while still achieving satisfactory results saving both time and money.
-
product
Laser Diode Characterization Testing
The Yelo Laser Diode Characterization system performs automated characterization of a laser device. The system will allow the operator to load a single packaged Laser device into a TEC controlled fixture mount. Each test station (LIV, Spectrum, Far Field/Beam Divergence) will then automatically align with the Laser Device in a sequential order and perform the automated tests required of each station.
-
product
Single Phase AC ISSRs
Series DRS
Series DRS relays are designed for all types of loads. These relays feature our new high efficiency back-to-back thyristors for long lifetime expectancy. The relays utilize optical isolation to protect the control from load transients. These relays are Zero-Cross switching.Features Include:• AC Semiconductor Contactor with Diagnostic• Compact size and DIN rail mounting• Zero Cross switch ON in case of overvoltage• Large control range: 3-32Vdc• IP20 housing• UL conformity
-
product
LXI Scalable Matrix Chassis
65-200-001
This LXI scalable matrix chassis offers you a solution that can be easily re-configured by the insertion and removal of up to six LXI matrix plug-in modules (detail in the tables below). It is purchased as an empty chassis with a quantity of plug-in modules required for a particular matrix size. Unused chassis slots are blanked off by the supplied blanking pieces. Cooling is provided by rear fans and front air intakes ensuring no wasted space when the chassis is rack mounted. The cooling system is adaptive to its operating environment to ensure the acoustic noise is minimized when used in quiet laboratory environments and low load conditions.
-
product
Double-Roller Dynanometer
R 100/1 | VP 230002
Maschinenbau Haldenwang GmbH & Co. KG.
The double roller dynamometer R 100/1 with eddy current brake on the right side of the vehicle and pneumatic lifting beam is designed to measure the performance of cars and stands out due to its extremely robust, durable and low-maintenance construction. The R 100/1 ensures highest measuring accuracy due to the power measurement at a constant rpm, speed or tractive force, including the drag power measurement. Operating methods such as load simulation, including optional modules for the measurement of external data, are possible.
-
product
NI STS
RF Test and Measurement Solutions, LLC
RFTMS is a leader in configuring systems to meet your needs, as well as designing load board, writing SW, and integrating the final solution. We do this for wafer test, packaged parts, and modules. RFTMS can address any level of integration that your parts employ, from a single functional block, i.e., Power Amplifier (PA) to System-on-a-Chip (SOIC). We test all sorts of RFICs.
-
product
DCDC
TA Series 18 Watt
The 18-Watt TA series operates over an ultra wide input range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 77% are typical over varying load conditions of 25% to 100%.
-
product
Low Power Programmable AC Source
61600 Series
Chroma Systems Solutions, Inc.
Power:500VA (61601)1000VA (61602)1500VA (61603)2000VA (61604)4000VA (61605)Voltage range: 0-150V/0-300V/AutoFrequency: 15Hz 1000HzCompact size and weight attributable to advance PWM technologyBuilt-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage, current limitOne-key recall for 9 different voltage and frequencyLow output impedance for testing IEC 61000-3-2 ( 61605 )Comprehensive measurement capability, V, Irms, Ipk, Inrush, P, Q, S, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates ON/OFFAnalog programming interface3 units combined to 3-phase power outputEasy-use software for operation and ON/OFF testOptional GPIB and RS-232C interfaceFull protection: OP,OC,OV and OT protection
-
product
Analog Oscilloscope
FS-404
*OSCILLOSCOPE: 40 MHz Dual Trace,Dual Trigger, 1mV Sensitivity, 10ns Resolution.*FUNCTION GENERATOR: 0.5Hz~5MHz Frequence, Sine,Square,Triangle,3 waveforms, Max output:20 Vp-p(No Load),10 Vp-p(50Ω? Load)., TTL Synchronous Output
-
product
3-slot Network Attached File Server
DTS3
Curtiss-Wright Defense Solutions
The Data Transport System 3-slot (DTS3) is a rugged Network Attached Storage (NAS) file server for use in mobile vehicles, field ground stations, and aircraft. The DTS3 is easily integrated into network centric systems providing an easy-to-use, turn-key, rugged Network File Server (NFS). The system houses three Removable Memory Cartridges (RMC) that provide quick off load of data.
-
product
Structural Load Monitoring
SLM
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
