Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A
C104DFX-2SB-1A
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied without backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
product
AOI & SPI Test Systems
Xceed AOI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The Xceed enables true 3D measurement and provides the most accurate and repeatable inspection results with the minimum false calls. It’s designed with Advanced Signal Processing which gives results in noise-less, clear, and accurate 3D images.
-
product
Grypper G35 / G40
*Package-size PCB footprint: Since the PCB footprint of Grypper is identical to the package, only one PCB design is required, enabling a seamless transition from test and validation through production and reducing overall cost of test*Low insertion force: Unique contact design reduces the insertion force required to insert and retain higher-ball-count packages safely and securely within the test socket*Oxide cutting wipe action: The contact design wipes the side of the solder ball during insertion, breaking through solder oxides ensuring a good electrical connection between contact and solder ball*Signal integrity: A short signal path achieves low inductance and low insertion loss, providing a nearly invisible electrical connection*Test socket has solder balls attached: The G40 contacts have solder balls reflowed onto the contacts to ensure reliable solder volume at the PCB to test socket solder interface.
-
product
Bonding Tester
PTR1102
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
-
product
Silver Ball Matrix Sockets
SM Contact is a unique contact that has precise silver balls held together by a proprietary conductive formulation. These conductive columns (diameter optimized for 50 ohm impedance) are suspended in a non-conductive flexible elastomer substrate with a patented solid core for enhanced durability and reliable performance over time, temperature and cycles. This flexible substrate is very compliant and resilient and enables the conductive columns to revert back to original shape when the force is removed. Solutions are available for 0.25mm to 1.27mm LGA, BGA, QFN, CSP, POP, WLP and other packages. The silver ball matrix contact technology is also available with a protective plunger matrix (a gold plated copper cylinder) that sits on top of the conductive columns. This plunger matrix protects the conductive column from contamination from various solder ball interfaces. A quickly replaceable plunger matrix enables minimal downtime during final production test. The product family code for this line of sockets is SMP.
-
product
BGA SMT Adapters
Giga-snaP™
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, is plugged into the female socket on the board thus interconnecting the chip and the system is ready to go. The SMT adapters have the same solder ball types as the chips they are emulating. These adapters have less than half of the insertion force of competitive adapters, shorter electrical path for highest speed, and can be solder reflowed numerous times. A complete description and drawings of Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapters can be found at the tables shown below.
-
product
AOI & SPI, Test Systems
SigmaX SPI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The SigmaXs inspection technology is unaffected by varying materials, surface conditions, or colors. The system profiles the board to generate accurate 3D shapes far superior to other brands and technologies.
-
product
Grypper "Y"
Ironwood Electronics Grypper Y contact is design to work with BGA devices with solder balls/bumps with no equator or small exposure where the standard Grypper cannot reliably hold on to the solder ball. The Y shape, working with the sliding lid, allows reliable contact and ensures device retention in high vibration application. Lower forces, <25 grams, makes insertion easier too and the less aggressive contacting allows 40+ insertions of the same device. The Sliding Lid can be configured to include heat sinking. The Y contact designs cover BGA devices from 0.35mm pitch and larger and the short electrical length has superior electrical performance.
-
product
Copper Pillar Bump
Like in conventional fabrication, integrated circuits are created on the wafer but near the end of the manufacturing process, the attachment pads are metalized on the surface of the chips to make them more receptive to solder. Then solder dots are deposited on each of the pads, and chips are cut, flipped, and positioned so that the solder balls are facing the connectors on the external circuitry.
-
product
Socket Accessories (SMT Options)
The SMT adapter consists of standard high temperature FR4 with plugged via technology, eutectic SN63PB37 solder balls or SAC lead free solder balls and threaded inserts for mounting the socket. The top side of adapter has SMT pads to receive socket interconnect and the bottom side has appropriate solder balls for corresponding pitch. This FR4 adapter with balls can be soldered to the SMT pads in the target board. Then socket can be mounted to the threaded insert on the FR4 adapter.
-
product
Solder Paste Analysis
SPA1000
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
product
25-Pin D-Type Female Solder Bucket
92-960-025-F
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
product
37-Pin D-Type Female Solder Bucket
92-960-037-F
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Ball Pressure Apparatus
BP-20
Is designed to perform tests specified in many standards where resistance of insulating materials to elevated operating temperatures is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaires, motors, connectors, etc. The test ensures that external parts of insulating material, the deterioration of which might cause the appliance to fail to comply with the relevant standards, are sufficiently resistant to heat.
-
product
1040g Steel Impact Ball Drop Impact Test Ball
CX-B104
Shenzhen Chuangxin Instruments Co., Ltd.
1040g Steel impact ball drop impact test ball
-
product
3D Solder Paste Inspection (SPI)
TR7007 SII
Offering inspection speeds of up to 200 cm2/sec, the TR7007 SII is the fastest solder paste inspection system in the industry. This highly accurate inline shadow-free solder paste inspection solution offers full 3D inspection at resolutions of 15 µm or 10 µm. Built on a high precision linear motor platform, the system's hallmark features include closed loop function, enhanced 2D imaging, auto-warp compensation and fringe pattern technology. Increase capacity without sacrificing additional space with an available dual-lane configuration.
-
product
High-speed 3D Solder Inspection Machine
YSi-SP
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
product
50-Pin D-Type Male Solder without Backshell
92-960-050-M
This connector is designed to allow users to directly terminate cables with soldered connections. 50-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module.
-
product
Ball Pressure Test
Premier Electrosystems' Ball Pressure Test is used to determine dimensional stability under stress at elevated temperatures. It analyses the relationship between the degree of deformation and the temperature when the test specimen is subjected to a constant load.
-
product
Solder Paste Inspection
3D SPI
Checking all the relevant points in the production process is essential, especially in terms of analyzing the causes of defects, fixing them, and – most importantly – preventing them in the future. That’s why solder paste printing is of fundamental importance for manufacturing complex assemblies: If paste printing isn’t performed correctly, the defect can impact the subsequent assembly and the soldering process, resulting in a tilted component or a poor or missing solder joint.
-
product
Ball Pressure Test Apparatus
The Ball Pressure Apparatus is designed to perform test specified in IS Standard where resistance of insulating material to elevated operating temperature is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaries, motors, connectors, etc. It is a precision engineered test instrument for use by safety and compliance testing laboratories.
-
product
Reflow / Wave Solder Process Dashboard
Vantage
Real-time dashboard for all reflow ovens in the factory. Accessible from all authorized PCs and mobile devices anywhere. KIC Vantage is a factory level Industry 4.0 smart factory system for reflow and cure data management and analytics. It truly does give you the best vantage, gaining insight into your reflow and cure processes throughout the factory.
-
product
Ball Pressure Tester
4710
The ball pressure tester is used to test the thermal properties of insulating materials. The test sample is placed in an oven and a steel ball is pressed against the surface. The impression of the steel ball is measured to see if it meets the requirements.
-
product
9-Pin D-type Female, Solder Bucket, HV
92-960-009-F-HV
9-Pin Female D-type Connector, High Voltage, Solder Bucket - Without Backshell
-
product
IEC60950 50mm Impact Test Balls
CX-15
Shenzhen Chuangxin Instruments Co., Ltd.
The Impact Test Ball is a specially machined ball to test impact resistance according to IEC, CSA and UL Standards. It is made of chrome-plated-steel for durability, and is fitted with an eyelet to facilitate testing for pendulum applications. Eyelet is threaded to the ball to allow attachment of a handle or force gauge. Weights are closely controlled.
-
product
160-Pin DIN41612 Connector, Solder Pin, Male
92-960-160-M
Suitable for users to create their own cable assemblies, this product can be supplied with or without the backshell. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the connector can be fitted with an optional screwlock assembly.
-
product
25-Pin D-Type Male Solder Bucket
92-960-025-M
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
product
Solder Joint Inspection System
DMC developed the software to inspect the solder joints of automotive power door lock switches.
-
product
Solder Paste Inspection System
LaserVision SP3D Mini
The LaserVision SP3D Mini offers the same level of overall measurement capabilities as the VisionPro SP3D. Utilizing a lower cost microscope platform and the ability for customers to supply their own PC if needed, the SP3D Mini sets the "affordable" boundary on reliable, low cost SPI solutions.
-
product
Tool, Solder Kit, Mini Coax with Solder Sleeve
910121144
Used to solder Mini Coax Solder Sleeve contacts.
