Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
43-752A-111
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Supercapacitor Test
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
product
Battery Analyzers
CA 1550 – Commercial Version
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
product
Battery Management Systems Testing
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
product
Full-Featured Life Cycle Test System
LCV
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
product
Battery Analyzer
KT-97E
● ImpedanceRange: 6mΩ / 60mΩ / 600m Ω / 6Ω (auto-range)Accuracy: ±1.5% of reading ±3digits Resolution: 0.001mΩ● CapacityRange: 0 ~ 9999Ah Accuracy: ±1.5% of reading ±3digits Resolution: 0.001Ah● DCV Range: 6V / 60V (auto-range) Accuracy: ±0.5% of reading ±3digits Resolution: 0.001V● DCARange: 6A / 60A / 200A (manual) Accuracy: ±1.5% of reading ±3digits Resolution: 0.001A / 0.01A / 0.1A● Temperature Range: -20℃~100℃Accuracy: ±1.0℃ Resolution: 0.1 ℃ ● Set discharge end voltage manually.● Auto alarm when capacity measurement finish .● Data Storage 50 records of impedance and voltage data are available to store into memory .● RS-232 ● Supplied with lithium rechargeable batteries, very easy to charge with AC power line. Application:● Measure the impedance and capability of rechargeable batteries. which voltage below 60V, ● A perfect tool for identify the batteries used in UPS devices, vehicle,emergency lighting, alarm, sprinkler systems, business security deviceselectro motion ca r etc..
-
product
Battery Fuel Gauge
Global Digital Instruments, LLC
SenDEC Battery Fuel Gauges are designed to accurately monitor the charge capacity of lead acid batteries. SenDEC fuel gauges can be used to monitor DC powered equipment such as fork lifts, golf carts, floor care equipment, and any other battery powered equipment. Three battery discharge profiles are standard, plus custom profiles, and a lockout option.
-
product
Analog Voltmeters
*Dual stick MARK series measure voltage and perform phasing operations from 0V to 75kV*No batteries or calibration required*Determines in-phase or out-of-phase*Determines underground cable faults*Discharges underground cables and other equipment that hold capacitive charges*Versatile for overhead and underground applications
-
product
Analyzers
BA500 Series
The BA500 analyzers are high performance battery analyzers with charge and discharge capabilities. The analyzers connect to your computer via USB and the BA500WIN software program is used to control the analyzer and battery under test. This system has a fast data collection system allowing you to collect and view as much data as required. Once you collect this data you can graph, analyze & save it.
-
product
Regenerative Battery Pack Test System
17040
Chroma Systems Solutions, Inc.
The 17040 Regenerative Battery Pack Test System is a high precision system specifically designed for secondary battery module and battery pack test. It has an energy regenerative function to greatly reduce power consumption during discharge, and ensure a stable power grid without generating harmonic pollution on other devices – even in dynamic charge and discharge conditions. It is capable of recycling the energy discharged by the battery pack test back to the grid reducing wasted energy that traditional equipment discharges in the form of heat.
-
product
Battery Cell Testing Equipment
Xiamen WinAck Battery Technology Co., Ltd.
The battery cycle life tester is a high-precisionsystem designed specifically for the battery cell charge and discharge testing.It is suitable for the battery cell cycle test, battery cell charge anddischarge aging test, battery cell performance test, battery cell capacitydetection test, battery cell IR test, deep-discharging test, function test ofhigh-power lithium-ion battery cells, such as EV battery module, ES batterymodule, super capacitor…
-
product
Analogue (1kV below) Insulation Tester
1832 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
product
25 Channel Potentiostat/Galvinostat
ArrayPGstat
For any selected cutoff voltage or current, early finishers are held at open circuit until all cells complete the charge or discharge period. All cells are switched at identical state-of-charge.- Multichannel potentiostat/galvanostat- Compliance voltage ±15 V- Voltage control ±10 V- Waveform signal sources (4 maximum)- ±100mA/channel (40 channels maximum)- 8 kHz bandwidth- Maximum scan rate 100 V/sec- Battery charge-discharge cycling: Time and/or voltage switching parameters.
-
product
Battery Pack Test System
*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery.
-
product
WizardOne Battery Charger-Analyzer for 4 AA / AAA
MH-C9000
It's like having four charger-analyzers for AA and AAA NiMH / NiCD batteries. Refresh & Analyze: Charges the battery, rest for one hour, discharge, rest again, then recharges it. Selectable charging and discharging rate. Break-In: Also known as IEC capacity measurement and "Battery Forming". Charges battery at 0.1C for 16 hours, rest for one hour, discharges battery at 0.2C, then recharges again at 0.1C for 16 hours.
-
product
Battery & Electrical System Testing
12-0200
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
product
Analogue (1kV below) Insulation Tester
8052 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.
-
product
Life Cycle Module Testing System
LCN
Full featured test system for quality control and R&DLife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
product
Electric Vehicle Battery Tester
The Electric Vehicle Battery Tester (EVT) is designed for testing traction batteries in electric vehicles or HEV batteries in hybrid electric vehicles. The EVT realizes the functions charge and discharge with freely programmable set values for current, voltage, power or resistance in test programs, as well as the registration of the corresponding measured data.
-
product
Battery Analyzers
CA 1550 – Military Version
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
product
Battery Charge Discharge Tester
KV Hipot Power Test Equipment Co.,Ltd
Battery Charge Discharge Tester is a multi-function comprehensive tester which is not only a battery charger and Battery discharger, but a battery activator.
-
product
Battery Charge & Discharge Test System
ITS5300
ITS5300 battery charge and discharge test system is designed for a variety of power batteries (lead acid, nickel hydrogen, lithium batteries, super capacitors, hydrogen fuel cells, etc.) for performance testing.
-
product
Regenerative Battery Pack Test System
17020
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced by the battery module ei ther back to the channel s in the sys tem performing a charging function or to the utility mains in the most energy efficient manner. This feature saves electricity, reduces the facilities thermal foot print and provides a green solution by reducing the environmental impact on our planet. Chroma's 17020 system is equipped with multiple independent channels to support dedicated charge / discharge tests, on multiple battery modules / packs, each with discrete test characteristics. The channels can easily be paralleled to support higher current requirements. This feature provides the ultimate flexibility between high channel count and high current testing.
-
product
Temperature Humidity Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Battery high low temperature test chamber is designed to test all types of batteries, including lithium-ion batteries. The battery test chamber has many safety functions built into the test chamber, which can handle battery tests and prevent safety accidents. Charge/discharge cycle testing, which determines the number of times a battery can be used by evaluating it until it deteriorates after repeated cycles of charging and discharging. In the laboratories involved in battery testing, tests based on charge and discharge cycles are a key activity. The instruments used for this type of test usually perform harsh and lengthy test protocols on the battery and can usually be connected to various instruments.
-
product
HDDH-3932 Single Cell Battery Activator
HD Power Test Equipment Co.ltd
HDDH-3932 Cell Activator is used to discharge and charge and activate for disable single cell battery, which is simple, safe and accurate test device.The instrument is with perfect protection function, sound and light alarm and clear interface tips.
-
product
Battery Discharge and Charge Tester
HD Power Test Equipment Co.ltd
Battery Discharge Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It can proceed the discharge and charge for the batteries to extend the lift-time.
-
product
Battery Charge and Discharge Tester
HTCFD / 790
Wuhan Huatian Electric Power Automation Co., Ltd.
The voltage monitoring information of single battery is simple, safe and accurate with wireless relay access.
-
product
Analogue (1kV below) Insulation Tester
1132 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
product
Discharge Test System
The automated testing equipment automatically performs charge and discharge of energy devices such as the rechargeable batteries(cells, modules, packs) that are installed in PHV/ EV and mobile devices, while measuring the voltage, current, temperature, and impedance.
-
product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
product
All in one system 32KWH LiFePO4 Lithium Battery with AC Charger and 15KW Inverter for mobile vehicle application
SPVLI-32KWH-INV15KW
Zhejiang Sandi Electric Co., Ltd
Our All in one system 32KWH LiFePO4 Lithium Battery with AC Charger and 12-15KW 120/240V Inverter for mobile vehicle application ESS including LiFePO4 Lithium Battery with BMS, off grid pure sine wave inverter, AC/DC charger.All-in-one design, high integration and space saving installation；Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years； Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability；Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage；BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range；CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability；System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell；Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable;Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as neededModel SPVLI-30KWH-INV12KWIsolation mode Low Frequency TransformerInverter PartBattery Input Rated Voltage (Vdc) 307VDC Voltage range (Vdc) 278-400VAC Output Rated output power 12KW Output waveform Pure Sine Wave Rated Voltage 120/240VAC Phases Split phase + N + PE Rated current (A) 50A(Phase Current) Frequency 60Hz Power Factor (PF) >0.95 Inverter Efficiency >92% Display LCD Overload Ability 150%, 35 secondsAC-DC Charger PartAC Input Voltage range(Vac) 180-240VacDC Output Rated voltage(Vdc) 330Vdc Rated current(A) 20ALithium Battery PartCell/Number 105AH/96PCSRated voltage 307VMax charge current 20AMax discharge current 100ACharge temperature range 0℃ ~ 50℃Discharge temperature range -20℃ ~ 50℃Cell charge end voltage 3.6VCell discharge end voltage 2.7VProtection Function Protection Input reverse polarity, under voltage, over voltage, output over-current, short circuit, overheating etc. Cooling method Fan-cooledDegree of protection IP20(indoor)Mechanical Dimension Depth* Width * Height 645x891x767mm Weight (Kg) 378Kg
