Filter Results By:
Products
Applications
Manufacturers
Voltage
The tension of an electromotive force.
- Pickering Interfaces Inc.
product
PXI 128x2 Matrix Module, 1-Pole, 2A, 60W
40-584-001
Our model 40-584, along with the following models40-584, 40-585, 40-586A and 40-587Aare high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays. The PXI matrix modules are designed for switching medium voltage and power signals. The user signal connection is via a robust 78, 50 or 37 pin D-Type or 160 pin DIN 41612 connector that is fully supported by the wide range of our cable and connector accessories.
-
product
Voltage References
Renesas' wide selection of voltage reference (Vref) circuits offer accurate and stable reference voltages unaffected by external influences such as variation in temperature, input voltage and time.
-
product
DC Voltage Sensors
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
product
PXI/PXIe High Voltage Power Relay Module, 7xSPST With Hardware Interlock
40-323-900-HI
The 40-323-900 (PXI) and 42-323-900 (PXIe) are 7xSPST relay modules suitable for applications requiring high voltage power switching with high density. They have current handling up to 0.25 A, cold switching up to 9 kVDC/9 kVAC peak and hot switching up to 7.5 kVDC/7.5 kVAC peak.
-
product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
780173-01
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
-
product
VOLTAGE TRANSFORMERS
Designing & manufacturing a range of high quality, voltage transformers in three different frame sizes for both measuring and protection duties. Transformers which are designed to comply with the requirements of IEC 61869-3 or other international standards as required can be supplied to satisfy most Low Voltage applications.
-
product
Combined High Voltage Test Set
is extensively used to measure AC and DC voltage of different electrical devices.
-
product
High Voltage 9-Pin D-Type Connector & Cable Accessories
The High Voltage 9-Pin D-Type connector is used on high voltage PXI and LXI switching products to provide a high voltageconnector solution. Connection solutions for modules with Standard Voltage Rating D-Type connectors are also available.
-
product
Pulsed Withstand Voltage Safety Test
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
product
200 A HIGH-CURRENT MICRO-OHMMETER
MPK-203x
The MPK-203x high-current micro-ohmmeter is a portable, microprocessor-controlled instrument. Has optimized filters and protections for measurements in electrical substations. Can be used to accurately measure very low contact resistances of high voltage circuit-breakers and switches, busbars, etc., with test currents up to 200A. It employs the 4 terminals-method (U/I measuring principle) to avoid errors caused by test leads and their contact resistances.
-
product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
WAVEFORM GENERATOR
WFG 600
The multichannel, high voltage, computer controlled Waveform Generator WFG600 is an exceptional instrument designed primarily for experiments on addressing liquid crystal devices and is most suitable for all applications where synchronized trains of pulses with variable width and amplitude are required.
-
product
Dielectric Withstand Tester
Weshine Electric Manufacturing Co., Ltd
The induction withstand voltage test of transformers and transformers is an important test to ensure that the quality of transformers conforms to national standards. The longitudinal insulation induction withstand voltage test of the inter-turn, inter-layer, inter-section and inter-phase insulation of the transformer winding is an important item in the transformer insulation test.
-
product
Dual Mobile Comm DC Source w/ Battery Emulation, DVM
66319D
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.
-
product
AC Current Sensor
RCTi and RCTi 3ph
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
product
Proving Unit & Voltage Tester Kit
DLPK1
Touch electrode for Quick testing of fused leads Optical and acoustic continuity Indication Low battery indication A portable, battery powered Proving Unit for testing Two Pole Voltage Testers up to 690V Continuity Tester for testing: Fuses, Fused test leads etc
-
product
DC Hipot Test Set
KVZG
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
product
MIL-STD-1553 Test & Simulation Interface for PCI
PCI-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - PCI & PCIx Compatible, 3.3V and 5V OperationApplication interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Flow Sensors
Accuracy±0.75% of full scale Measuring pipe size range DN 15 to DN 600(0.5 to 24 inch) Measuring flow rate range 0.15 to 8 M/s(0.5 to 26 Ft/s) Field-rangable supply voltage from DC 5 to 24 VS Field-rangable operting temperature from -20 to 90°C(-4 to 194°F) Protection class NEMA4(IP65) or NEMA6,6P(IP68) CE EMC certification
-
product
Dual Channel High Voltage Linear Amplifier
A800D
This unit contains two independent A800 amplifiers that share common ground reference and power supply.
-
product
Modbus Controllers
Datexel has a range of Modbus RTU Masters, Slaves, Controllers, Data Loggers and Modbus remote displays. The DAT9000 is a Modbus RTU Master with RS485, RS232 and Ethernet Interfaces. The DAT9000IO is similar to the DAT9000 but it has digital input and outputs. The DAT9000DL has an additional Data Logging facility and the DAT9000DLIO has both Data Logging and digital IO. The DAT9011 is a Modbus Master with 2 analog inputs which can chose from Thermocouple's, RTD's, Potentiometers, mA and mV's. It also has 2 outputs which can be mA or voltage. The DAT9011 can also accept digital inputs and provide 2 SPDT relay outputs. The DAT9011DL also has a Data Logging facility which can store up to 8gb of readings on a thumb drive.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
DRO/VCO Modules
The Analog Devices portfolio of dielectric resonant oscillators (DROs) and voltage controlled oscillators (VCOs) offer excellent output power and phase noise performance over temperature and cover a range of applications and uses to meet the needs of industrial, medical, aerospace and defense, EW, ECM, and communications markets. Our DRO modules are a natural choice for applications in fixed tuned or narrowband tunable configuration, while our selection of VCOs play a key role in providing reliable frequency generation for RF and microwave communication and test systems.
-
product
Digital Insulation and Continuity Tester
Metra Insu 20
Metra Insu 20 digital insulation and continuity tester is suitable for folloving.• Measurement of the insulation resistance on electrically dead equioment and systems with test voltages up to 1000 V. • For testing motors, transformers, generators, switchgears. • for testing of house hold appliances. • Measurement of the insulation resistance of cables. • Very useful for on-site maintenance and service departments.
-
product
POWER PROBE III WITH CLAM SHELL - GREEN
PP3CSGRN
*Power Probe 3 is a digital multimeter that provides diagnostic power with the flip of a switch*Determine if motors, lights, fans, relays and circuits are operational on and off the vehicle by applying battery power or ground through the tool*Easy-to-read dual polarity indicators feature a red (+) symbol to indicate positive voltage and a green (-) symbol to indicate ground
-
product
PXI-4072, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter
778270-01
6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter - The PXI‑4072 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXI‑4072 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, frequency, period, and basic L and C measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXI‑4072 can acquire waveforms at sample rates up to 1.8
-
product
Transformer Polarity Tester
PMT20030
Power Measurement Technologies Inc.
A hand held instrument for polarity identification of current, voltage and power transformers with an operable ratio range from 1:1 to greater than 5000:1.
-
product
Power Quality Analyser
PM1000
The PowerMaster 1000 Single Phase Logger is a 3-channel data logging system built into an easy to carry housing. It is ideal for responding to residential voltage complaints and power consumption problems. It is particularly useful for troubleshooting.
-
product
PCI-5922, 24-Bit, Flexible Resolution PCI Oscilloscope Device
779659-02
24-Bit, Flexible Resolution PCI Oscilloscope Device - The PCI‑5922 high resolution oscilloscope device features a flexible measurement resolution range up to 24 bits and up to 15 MS/s rates. This oscilloscope device has flexible settings for coupling, and voltage range, as well as a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. The PCI‑5922 is capable of taking extremely resolute and accurate analog measurements. It is ideal for audio signals, spectrum analysis, and any other small, accurate signal measurements.
-
product
Conductivity / TDS Monitor / Controllers
750 Series II Conductivity Monitor & Controllers
The unique circuitry of the 750 Series II Conductivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
product
Clamp type AC Current Sensor／with DC Voltage Output
ACT-5H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 0.1A～5A*DC 5V full scale output
