Filter Results By:
Products
Applications
Manufacturers
RS-422
One of several standards that incorporate balanced line signals into DB connectors. A pair of wires is used to carry each signal. The data is encoded and decoded as a differential voltage between the two lines. (www.sangoma.com)
- TEAM SOLUTIONS, INC.
product
4-Port Serial Interface
APCI-7500-3
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
product
RS-485/RS-422 Fault Protected
Renesas' fault protected RS-485/RS-422 transceivers, also known as overvoltage protected transceivers (OVP), offer robust fault tolerance and high performance.
-
product
RS-485/RS-422
Renesas' half duplex and full duplex RS-485/RS-422 transceivers are available in a variety of speed grades to address any application needing reliable data transmission over twisted pair wiring.
-
product
Solid State Digital Matrix Switching Systems
DX Series
Cytec's DX Series Switching Systems are based on solid state switch fabric. All systems are non-blocking (any input to any output) and full fan-out (any input to any or all outputs)The DX/256x256 systems are designed to switch TTL, CMOS, LVTTL, IRIG, RS232 and RS422 up to 80 Mbps NRZ. Input and output buffers are used to convert to RS422 and/or RS232 signal levels as needed.The DXM/64x64 and DXM/128x128 are modular systems capable of switching data rates to 3.2 Gbps NRZ. They are intended to switch RS422, ECL, PECL, LVDS, CML and virtually any type of digital data stream. Configurations as large as 128x128 Clock and Data systems can be easily configured.The DX/64x64 is an earlier version of the DXM and offers systems up to 64x64 with SMA connectors for ECL, PECL, LVDS or RS422.
-
product
Multiprotocol Serial Card
PCIe-ICM-4SM
The PCIe-ICM Series are a new family of isolated PCI Express serial communication cards. These PCI Express cards feature a selection of 4 or 2-ports of isolated, software selectable, RS-232, RS-422, and RS-485 serial protocols.
-
product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
PMC-BiSerial
Two fully independent and highly programmable RS-485 / RS-422 IO channels are provided by the PMC-BiSerial design. The channels are supported by two independent state-machines created within the Xilinx FPGA. The transmit and receive protocol can be the same or different. Manchester encoding and decoding, standard serial [UART], control, command, instrumentation, and custom protocols can be implemented.
-
product
Camera Link Translators
CLT-303
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
product
64 Channel Digital Output and 4 Channel RS422 Module
DP-OBC-3006
DP-OBC-3006 is a 3U cPCI-based board with 64 Digital Output channels and 4 ports of RS422 serial interface. It has 64 digital output channels in open/ground configuration and operates on 32-bit, 33MHz PCI bus. Four RS422 channels are incorporated with opto-isolated inputs which supports baud rates upto 115. Kbps.
-
product
Dual-Port Isolated RS-422/485 Communications and Watchdog Card
WDG-2S
This multifunction card contains a watchdog timer, two RS422/485 serial communications ports, and an internal temperature monitor and computer voltage monitor. This is a full-length card that installs in "long" expansion slots of IBM PC/XT/AT and compatible computers. The following paragraphs describe functions provided.
-
product
Long-range Surveillance Thermal Imaging Camera
IRT303
Wuhan JOHO Technology Co., Ltd
Long-range Surveillance Thermal Imaging Camera IRT303IRT303 is extremely compact, durable uncooled day/night system, operating in 8-14 um waveband, with DDE image processing technology and high sensitivity, it is ideal for quick and accurate situational awareness in a variety of defense and security applications. It specially equipped with Dual-FOV, the wide FOV for find object in wide scope and then fast switch to narrow FOV looking at the target for details. IRT303 is the optimal device for super long observation purpose and target acquisition.ApplicationsLong distance surveillance or patrolLand border and coast surveillanceMarine navigation or rescueTechnical DataDetector Detector material Uncooled FPA Spectral range 8~14 m Pixels 320x240 Pitch 38 mx38 m NETD 50mK@25 C (f/0.7) Optics Lens 135mm/45mm FOV 5.2 3.9 /15.4 11.6 Focusing Motorized Optional lens 100mm/25mm, 120mm/40mm, 150mm/50mm, 180mm/60mm Image Presentation Video output 25Hz PAL/30Hz NTSC Electronic Zoom x2 Polarity BH/WH inverse Brightness & Contrast Auto/ Manual Gain Composition Auto/ Manual Power system Power supply 110~240VAC 9~14VDC (typical: 12VDC) Interfaces Command interface RS232 /RS485/ RS422 alternative Digital video interface(Optional ) Ethernet/LVDS/CameraLink Environmental Ambient temperature -40 C~+60 C Storage temperature -45 C~+60 C Range Performance Detection Range (2.3mx2.3m vehicle) 5500m Recognition Range (2.3mx2.3m vehiclet) 1800m Detection Range (1.8mx0.5m human) 2200m Recognition Range (1.8x0.5m human) 580m
-
product
Interface RS-485 and RS-422
The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus. Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications.
-
product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
- RS-422/485 DIN Rail Mounted Lightning/Surge Protector
Model 8022NX
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Full Duplex; Triple Stage Protection. The Model 8022NX is a DIN Rail mounted surge suppressor for 4-wire RS-422 or RS-485 circuits used to protect factory data networks, or, any network that wants to avail itself of the DIN Rail packaging concept. The Model 8022NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
product
RS-422 RS-423 RS-485
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
product
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs, for RS-422/485
540041010201
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs
-
product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
product
Sound Velocity Sensors
SVP 70
Compact and robust, the SVP 70 features a long path length whether you install it on a survey vessel, or take it down to 6,000 metres on an ROV, AUV or submarine.The SVP 70 is an all-titanium plug -n- play system with RESON SV processors, wide input voltage and RS232 and RS422 communication interfaces for long cable runs.
-
product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
product
6U Compact PCI Multiport Serial Card
CP69002
LinkedHope Intelligent Technologies Co.,Ltd.
CP69002 is designed as 6U Compact PCI Multiport Serial Card. The eight serial ports are in depended and magnetic isolated. The transform mode can be configured as RS232, RS422 and RS485 through the jumpers. The upstream interface is 32 bit 33MHz PCI bus.
-
product
4 Serial Communication Channels, Programmable RS-232/422/485, Non-Isolated
SC6
Serial Communication Module SC6 provides up to 4 high-speed, programmable RS-232/422/485, individually non-isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel non-isolated returns are available as part of the channel user interface signal set (for SE or SYS-GND reference).
-
product
USB to RS-422/RS-485 Converter
ND-6530
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
RS232 / RS485 / RS422 To Fiber Optic Converters
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
-
product
Serial Data Converters
CONV232/485 and CONV232/422
CONV232/485 and CONV232/422 convert between RS-232 communications (as used by the COM1 and COM2 ports standard on most motherboards) and balanced-mode, long distance RS-485 and RS-422 communications. CONV232/485 was designed for use with our REMOTE ACCES line when there is no RS-485 port on your PC, but may also be used in other, similar applications.
-
product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-94
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
3U Processor Board
CP39101
LinkedHope Intelligent Technologies Co.,Ltd.
CP39101 is a 3U CompactPCI 4-channel independent isolated serial communication board, designed for industrial communication applications, compliant with PICMG R3.0 2.1 specification.CP39101 adopts EXER 17D158 communication processor as the master control chip. Each of the on-board 4-channel serial port can be individually configured as RS232, RS485 or RS422, and in any mode, CP39101 can be operated properly in extended temperature ( -40℃ to +85℃ ) range.
-
product
GPIB Serial Interface
Model 4894B
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Expanded baud rate range from 50 to 115,200 baud.* 256 Kbyte RAM buffer for spooling data.* Over 600 Kbyte/second GPIB data transfer rate.*Transparent data transfer.* Programmable replacement for the NI CV interfaces.* 1 U high rack mount kit mounts one or two 4894Bs* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
product
- RS-422 to Fiber Optic Converter
Model 272A
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
product
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs, for RS-422/485
540041010101
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs
