Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
High Voltage 50 Pin D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Voltage Testers
Shenzhen Everbest Machinery Industry Co.,Ltd.
Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g
-
product
Voltage Testers
Non-Contact Voltage (NCV) tester quickly checks for the presence of voltage in AC powered systems. It can be safely used up to 1000 V AC. When AC voltage is detected, the testo 745 gives indication by flashing of its RED LED tip and buzzing of its internal audible buzzer. You can easily determine the hot and neutral legs of an outlet without time consuming and risky removal of the outlet from the outlet box.
-
product
Lead Acid Intelligent Battery Tester
612
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
product
Multi Function Automobile Tester
6521
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance and power providing testing.
-
product
Megohmmeter Insulation Tester
AMIC-30
The AMIC-30 insulation tester is a small portable meter designed to measure insulation resistance in electrical and telecommunications installations, cables, motors, transformers and other equipment. The test voltage can be programmed in steps from 10 V to 1000 V. The instrument can measure both insulation resistance over a wide range (0,1kΩ...100GΩ), and insulation leakage current, capacitance and other parameters. All test results can be stored in the internal memory and sent to a computer via the included wireless USB receiver. The meters are supplied with rechargeable Ni-Cd batteries.
-
product
Supercapacitor Test
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
product
Electrical Testers
When you work with electricity, you want tools that are field tested and proven to meet the highest standards. All Amprobe tools undergo rigorous examination in our state of the art testing labs, ensuring quality and full compliance with the latest IEC and CE safety regulations. They are also listed with third party certification labs worldwide. Amprobe electrical testers include circuit tracers and testers, non-contact voltage detectors, voltage meters, socket testers and more to cover all aspects of electrical testing.
-
product
High Voltage Tester For Hair Dryer & Hair Straightner
Every electrical apparatus or machine consists of two distinct sections - one which carries the electricity, and other which is isolated (insulated) from the electric currents. The former may be called the `Live' side whiles the latter `Earth’ side. A person near about the apparatus or handling it can safely touch the Earth side, but not the live side, for obvious reasons. To ensure that the isolation of the two sections is effected properly, the apparatus is tested by subjecting it to a Voltage much higher than the normal working Voltage. If the insulation is good, it stands the test without breakdown otherwise high electrical stress punctures the insulation at its weakest spot foretelling a later calamity to unwary user. Government Department- when buying electrical equipments- and all reputable manufacturers test every piece of equipment by this test called HIGH VOLTAGE TEST. It weeds out poorly insulate apparatus.
-
product
Arc/LED Lighting Testers
This system is a modern replacement for an obsolete product tester. This tester Hipots the lamp under test, checks for proper operation at the required voltage and also detects short circuit operation and the 5KV ignitor pulse signal. This tester allows for quick calibration to permit traceable/repeatable results and store the test results for product tracking.
-
product
High Accuracy Digital Puncture Tester
KT-5000Pi
This product improves the absurdity that the existing Puncture Tester has many errors between the indicated voltage on its meter and the real output voltage, and also that one cannot check how much current flows during test, and then attaches a voltage meter and a current meter. Its accuracy is high due to Digital method adopting a three point adjustment type. Also, for user's convenience and for making easy to connect with automation line, many input, output functions are added. Now, Puncture Tester also should be accurate and a high-grade product
-
product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
product
12-24V Multi-functional Auto Tester With LCD Display
6511
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 12-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
product
High Voltage EMC Surge Generator
TM510
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
product
Live-dead_Live Meter Verifier
LDL-1100
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 50 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL 1100 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
product
100-250V AC/DC Voltage Tester
7321A
Peaceful Thriving Enterprise Co Ltd
*Check voltage on 100-250V AC/DC.*Built-in neon lamp for 120V and 240V AC/DC.*Large, high visibility neon indicator positively identifies the presence of voltage.
-
product
Signature Model Surge Testers
SP
Surge / DC Hi-Pot testing capabilities. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope plus a DC Hi-Pot Tester. DC Hi-Pot testing with dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip. This dual tester combo is still capable of testing 3 phase motors with or without rotors.
-
product
USB TESTER, 3-9V, 3A, WHITE
72-13540
*USB tester inspects USB charger & portable power source*Lightweight and portable*LCD backlight*High/low output voltage warning*10 sets of data memory
-
product
HEV & EV Power Tester
EVd-40
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.
-
product
High Voltage Breakdown Tester
Model HV-100B
Laxtronics Instruments & Controls Pvt. Ltd
DC Output: 0 to 10 Kilo Volts continuously variable, AC Output: 0 to 5 Kilo Volts continuously Variable, Current Limit: 0 t
-
product
Battery Discharge and Capacity Testers
HD Power Test Equipment Co.ltd
HDFD Battery Discharge Tester can be used as the discharge load in the battery off-line state to realize the constant discharge at the set value by regulating continuously the discharge current. When discharging, the tester will automatically stop discharging when the voltage on the battery group terminal or the cell falls to the set lower limit value, or when the set discharging time is out, or when it reaches the set discharging capacity. Battery Discharge Tester can records all valuable and continuous real-time data during the discharge process.This tester system is simple, safe and accurate for monitoring voltage of cells adopting wireless connection.
-
product
HIPOTS (High Voltage Testers) / AC Hand Gloove and Boot Safety Tester
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Compact and rugged BDV testers for AC dielectric withstand / breakdown testing of Safety glooves and boots. Panel mounted controls and indicators with easy to follow legend.
-
product
Stand Alone Low Voltage Tester
Model 64×2
Internal Memory: 8 program locations without test point labels or 2 program locations with test point labels. Removable Memory: 16 program locations without test point labels, or 4 program locations with test point labels.
-
product
SNAPSHOT
PH-200
The Snapshot cable checker gives professionals and layman the ability to check cables instantly upon plug-in, with no buttons pressed or displays read. With its built-in memory, the Snapshot simply checks each cable plugged in against a correctly-configured cable pre-set by the user, and indicates the cable’s status with a sound. For pin-by-pin cable checking, the 〝standard check〞mode offers a plain LED-displayed check of the cable’s pins, checked automatically or manually. The Snapshot also generates a tone along the length of cables, making finding and following the cable with a tone probe a snap. A remote unit allows testing of already-installed cables, and a built-in line tester verifies phone line polarity and detects voltage before it threatens the safety of the test unit. A shield-test feature automatically tests cable shielding and a battery-low indicator prevents misreading results.
-
product
35b profile VDSL2 Tester
TM600P
*TM-600 VDSL tester specially designed for xDSL line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL, VDSL2 etc) and maintenance It provides xDSL test, PPPoE dial test, DMM test, Modem emulation, line voltage indication and so on.
-
product
Non-Contact Voltage Tester
NCVT-1
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
product
H.V. Proving Unit (DCV)
2713 PU
Standard Electric Works Co., Ltd
● Designed to proof: -Phasing sticks. -High voltage detectors (contact type only, not to be used with non contact proximity detectors.) -High voltage and voltage testers.● Battery operated.● Led indicates when power is “ON”.● Small and hand-held.● Quick connection with normal 4mm test leads.
-
product
CDM Tester
Hanwa Electronic Ind. Co.,Ltd.
The tester implements to test the withstand voltage which occurs when the device contact to different electric potential object.
-
product
Insulation Meters
Here you will find an insulation tester for a variety of ranges between 50 mega ohms and 2000 mega ohms. The portable manual insulation tester is used for determining insulation resistance, continuous current, alternating current and testing. With an insulation tester, measurements can be taken for different voltages, beginning with 100V up to 10,000V. Measurements meet the DIN VDE 0413 part 1 standard. The insulation tester comes with a test mechanism, clips, batteries and a carrying case. The insulation meter can be equipped for test laboratories if an optional DIN EN ISO is acquired.Measurement of insulation in cables and motor coils is vitally important for the prevention of accidents and damage to installations and is obligatory according to most codes of conduct.
-
product
Dual High Voltage Power Supply Tester
MS 1110
DHVPS Tester is used to test and service the dual high voltage power supply units. High Voltages of range from 4KV to 11KV can be tested.
